Aksman I agree, tons of videos on RUclips but nothing that breaks it down like yours... how could i connect a batter tender and add a plug outlet to the box?
You could install a tender plug but it would be easier (and less expensive) to charge the battery outside the box. I don't like to charge batteries when they are still connected to circuits as a safety precaution.
@@Aksmaniyak Huh? It is called a circuit design. Those of you watching this and using it to build anything related would be better advantaged to watch MANY others and compare.
I am continually amazed how many of these DIY videos either leave out the box name and size, or the battery name and size (not to mention other important parts). I only wish that all the countless batteries out there had a good fit with these varying size boxes; but I'll go ahead and order the battery after searching for a while and spend $$ and then hope it fits...
Hi. I'm not sure if you are writing about my video because I do list the parts in the narrative section. Once you know that, you can measure the interior of the box to determine what battery size will work for you. I don't usually list a specific battery because there are so many options for somebody to choose. I hope it works well for you. I do have another battery box video version that may work for you.
When you talk about connecting the negative and positive of the switches together, what's the purpose? The red and black wires are connected (between the two switches on the diagram) please clarify- I appreciate your help... I'm trying to figure out how to make my own...this is great info
Enjoyed your video! I know very little about electricty! I am studing videos like yours to try to learn. I am wondering , how do you keep an eye on the drainage of power when using the usb port?
Thank you Isaac. The USB port draws very little power so it is not really a concern. The important thing to watch is the voltage drop to make sure it does not go too low. Good luck on your studies!
@@Aksmaniyak That doesn't answer the question. If someone is trying to copy your design because they think it is the best thing since Edison's light bulb, you need to answer their specific questions. The box has specific dimensions given. We all know those are relative to the opening, the base, side bulge, etc. What size battery did you use specifically? That was the question asked. STEP UP DUDE, answer the questions of your viewers.
It is because he has no clue... You always cut the positive side, whether it is a switch or a fuse, look at current flow, positive to ground (negative). If you have a failure that results in a short, by having the switch/fuse on the positive side, you end all current flowing into the circuit. No current flow, no circuit.
The left switch powers on the 12V cigarette lighter and the right switch turns on the voltmeter and USB port. This helps save power if you only want to use one of the power ports.
You could hook up a charging plug to the box but you would need to use a battery charger to recharge the voltage. A set up like this would not charge directly from a car lighter plug.
Yes. There are 2 "jacks" in the 5V USB port. One is 2.1A and the other is 1A. I put the USB and voltmeter on one circuit because of the small amp draw. I put the power port on its own circuit because it can handle higher amp loads.
I actually made some extras to bring the cost down when buying parts. I was thinking about listing one on the FB page Kayak Buy/Sell/Trade to see if it would sell. What do you think?
Nice choice of box! I would have put both switches on one side, and used the empty side to store an emergency cellphone... Even without a SIM card in it, any working phone can call *911 -- Do you know where your old phone is? ;-)
Nice to see someone putting up a decent circuit diagram
Thanks Jim.
Aksman I agree, tons of videos on RUclips but nothing that breaks it down like yours... how could i connect a batter tender and add a plug outlet to the box?
You could install a tender plug but it would be easier (and less expensive) to charge the battery outside the box. I don't like to charge batteries when they are still connected to circuits as a safety precaution.
@@Aksmaniyak Huh? It is called a circuit design. Those of you watching this and using it to build anything related would be better advantaged to watch MANY others and compare.
This Paul dude is a trip. For some reason hating towards the poster in every other reply. Serious issues you have brother..........
I am continually amazed how many of these DIY videos either leave out the box name and size, or the battery name and size (not to mention other important parts). I only wish that all the countless batteries out there had a good fit with these varying size boxes; but I'll go ahead and order the battery after searching for a while and spend $$ and then hope it fits...
Hi. I'm not sure if you are writing about my video because I do list the parts in the narrative section. Once you know that, you can measure the interior of the box to determine what battery size will work for you. I don't usually list a specific battery because there are so many options for somebody to choose. I hope it works well for you. I do have another battery box video version that may work for you.
Thank you for the visual helpful
You are welcome Christopher.
Great project! Can I use 12v 20a switches? or they need to be 12v 30a ? Thanks in advance.
Thanks Adrian. The amp rating for your switches depends on what you want to run on your box. So you can use other switches.
Awesome video mate. Have you got the link to order that box? I’m in Australia
Thanks! It is listed in the narrative but here is the Walmart link: www.walmart.com/ip/Attwood-Boater-s-Dry-Box/16203650
When you talk about connecting the negative and positive of the switches together, what's the purpose? The red and black wires are connected (between the two switches on the diagram) please clarify- I appreciate your help... I'm trying to figure out how to make my own...this is great info
If you look where the black wire makes a hump that means it's a separate circuit not a connection point
Please the name of the box where can I get this orange box txs
The box is listed in the narrative. You can get it from Amazon or Walmart.
Enjoyed your video! I know very little about electricty! I am studing videos like yours to try to learn. I am wondering , how do you keep an eye on the drainage of power when using the usb port?
Thank you Isaac. The USB port draws very little power so it is not really a concern. The important thing to watch is the voltage drop to make sure it does not go too low. Good luck on your studies!
Where did you get that voltmeter/power combo?
Amazon and Ebay sell them.
What battery size did you use or what size fix in? A lawn and garden battery or a power sport battery?
It depends on the battery. I included the inside dimensions of the box. So you just need the battery you like and measure to see if it will fit.
@@Aksmaniyak That doesn't answer the question. If someone is trying to copy your design because they think it is the best thing since Edison's light bulb, you need to answer their specific questions. The box has specific dimensions given. We all know those are relative to the opening, the base, side bulge, etc. What size battery did you use specifically? That was the question asked. STEP UP DUDE, answer the questions of your viewers.
@@appa561 z
I thought a power switch was always put on the positive side. If not can you tell me why its on the negative side?
I don't understand your question. Each switch has pos/neg connections for the separate circuits.
It is because he has no clue... You always cut the positive side, whether it is a switch or a fuse, look at current flow, positive to ground (negative). If you have a failure that results in a short, by having the switch/fuse on the positive side, you end all current flowing into the circuit. No current flow, no circuit.
Can you explain what the switches are for?
The left switch powers on the 12V cigarette lighter and the right switch turns on the voltmeter and USB port. This helps save power if you only want to use one of the power ports.
Aksman thanks for the info! What kind of wire do you recommend?
You are welcome Charles. I used 16 gauge marine rated wire.
@@charlesaquino4277 Ask him for the formula that determined 16 guage. You have no idea if he guessed correctly.
no provision for charging the battery while in the box?
Not with this design.
Might be an interesting mod!!! Would love to see that. @@Aksmaniyak
Hi James. I did make another battery box version with that feature. Just check out my other video for the design.
@@Aksmaniyak I'll check your other videos
@@Aksmaniyak Why not actually post the link to your video for the design in question?
What gauge wire would work best with 2 12v battery's paralleled?
I would use at least 14 gauge.
How much current draw? Gauge of the wire is determined by current draw, not voltage.
Ok, one question. could you simply connect a 12volt plug from this to a 12volt cigar socket in my vehicle to charge this up during the jouney to camp?
You could hook up a charging plug to the box but you would need to use a battery charger to recharge the voltage. A set up like this would not charge directly from a car lighter plug.
So to plug anything in that lid needs to be opened?
Yes. But if you don't want to do that, you can remove the top lid from the hinges and leave the faces of the gauges/switches exposed.
@@Aksmaniyak Therefore removing the feature you bought the box for... I don't get that logic... That's just me.
Where I can buy that kind of box
I bought it at Walmart. It was in the fishing/boating section.
Where can I get that box from?? Got a link?
I bought it from Walmart. It is in the boating/fishing section.
was this battery box made to power your trolling motor?
No, it was made to power smaller electronics.
Nice switch and power supply unit. What is the 12V USB port for a fish finder?
Thanks Wayn. No that port is for a cell phone, tablet, and other small chargers.
This USB port has the voltage regulator built in like a automotive power port plug USB adapter to convert the 12VDC to 5VDC for charging the phone?
Yes. There are 2 "jacks" in the 5V USB port. One is 2.1A and the other is 1A. I put the USB and voltmeter on one circuit because of the small amp draw. I put the power port on its own circuit because it can handle higher amp loads.
I may have to get one of those myself.
I actually made some extras to bring the cost down when buying parts. I was thinking about listing one on the FB page Kayak Buy/Sell/Trade to see if it would sell. What do you think?
how do you recharge the battery?
By removing the battery and charging it.
i guess I should have asked what specific charger you used
I bought a Schumaker charger from Walmart.
roger that sir- thanks for the info great project btw-
Personally. I would have put the fuse between the switches and the battery. But otherwise, nice build.
Thanks.
Nice choice of box!
I would have put both switches on one side, and used the empty side to store an emergency cellphone...
Even without a SIM card in it, any working phone can call *911 -- Do you know where your old phone is? ;-)
Thanks Robert.
Once again you show no battery, no battery specifications or model numbers in this video.... ☹️
Because there are several options.
How do you recharge the battery.?
On that design you use a standard battery charger. On the later version their is an external connector that is used.
@@Aksmaniyak you mean do I have to take the battery out of the box?
For that older version yes. The new version you do not have to remove the battery. ruclips.net/video/tWRIpTLNIbg/видео.html