Thank you! I have a blown unit from China that is similar, but the chips had the numbers sanded off. Mine works great, with Tesla pan cake coils, and can run large Dc motors. Adding capacitors and schottky diodes bridge gets over 378 volts DC output. Good fun! ( a copper foil output coil was a bad idea) Cheers Warren
@@Didi1.275 yup. and they also cant explain how the number of turns affects the power that will be delivered to the workpiece as its just a transformer reflecting impedances at the square of the turns ratio... im running one off of 150V, and i can actually get a genuine 2kw.... no clickbait required. the really interesting part about this? first... a g40n60 is an IGBT. and ZVS oscillators dont work with IGBTs... then theres those diodes. 1n4007? really? at 250khz? a plain old standard 1n4007? i suspect someones doing a bit of cheating regards their little demonstrations versus what they actually "made". there is a reason most of my time on YT is now spent simply reporting all these clickbait scam channels with DIY "instructional" BS videos.
Este circuito se ve mucho en internet, es un oscilador que a la vez es driver ZVS y realmente funciona muy bien. Es obvio que ni de broma obtienes 2kW a 12V pero con el mismo tipo de circuito, otros componentes y mas tensión, nada que no se pueda hacer :P
12 V supply, 2 kilowatts will demand over 160 (!) amps. No way the clip leads can carry that much current. Nice idea, but don't believe the 2 kW. For comparison, a car starter motor draws under 100 A at 12 V.
Да конечно чушь... На вход сколько подают? 12 v. при 100% кпд надо 167 А а так 170-180 А. это сварочный ток, который для 10 мм электродов... Там провода 50 мм кв. А тут 1.76 мм кв... ну раз в 10 меньше!
induction cooker €22 + made of square iron pipes 20*20 mm, welded a square loop 20*20 cm, let water through it, added thermal switches, thermovalves, pressure safety valves, a pump for central heating and with 1000 W I heat an apartment of 100 m2. Added more converter 12-220, 1000W, solar collectors 1500W, battery 12 v 200 A and works
Need to pull this to bits a little. The 'G40N60 IGBT's are rated at 625 Watts each but not your circuit. The 10K resistors are colour coded for 100K. The green choke is intended for noise supression not as a power inductor (totally different permubility). You can use any size of coil and alter the capacitors so that the resonant frequency is within the range of the IGBT's.
The 10k resistors are colour-coded correctly. The common mode choke he's using as a saturable centre-tapped inductor is demonstrably suitable - it has a high permeability core. It determines the switching frequency to a large extent.
@@ajatsingle1703 well, believe me or not but if you put an AC signal into a resonance circuit with the exact frequency, the voltage and current across a resonance circuit will rises to infinity if there no resistance This circuit works like an pendulum and 2 mosfet act like 2 hand pushing it every oscillating cycle
Good clear video, al though the coil in the middle being cut in the middle and resoldered a little confusing. 2000W and that blade should go white and melt. A 12v car battery will blow a hacksaw blade in two quite quickly, (as I found out)
Bu devre kullanılabilecek bir devredir. Evet DC gerilimden dolayı 2kW olması imkansız, ancak bu devreye olduğu gibi 110-220 VDC uygulanır ve bobin de su ile soğutulursa 2 kW rahat verir. 1N4007 olmaz diyenlerede şunu söyleyeceğim diodun hızından dolayı MOSFET ler rahat çalışabiliyor. Aksi taktirde miller bölgesine girer girmez mosfet kapanacak ve bir kaç MHz de çalışmaya çalışıp patlayacaktır. Sevgiler saygılar.
Zafer bey ellerinize sağlık video larınızı izleyerek yaptığım indüksiyon ısıtıcı ile Erzincan da 2765 watt ile kömüre veda ettik sizi severek takip etmeye DEVAM ediyoruz
@@muhammetakgoz2996 yaptığımız sistem ile 2750watt saat elektrik ile günde ortalama 8 saat yâni kombi gibi ısıyı yakalayınca sistem kapanıyor sistemdeki su 10 derece soğuyunca tekrar çalışıyor bu şekilde kömürün her türlü derdinden kurtulduk
Rüzgar gülünden elektirik alırsan bedavaya ısınırsın ama sessiz yap malum vergi kaçırdın diyip içeri almasınlar :) Bu diğer videolarda ki gibi demir boruyu indiksiyon bobinin içinden geçiriyorlar o şekilde ısıtıyor değilmi?
i can not see how much amperes it takes, i have ebay 12v/120w inductive heater and it works ok but it is to weak for my need, if it would be double power it would be nice
Übrigens , Leistung ist Spannung * Strom. Wenn die Spannung grösser wird verringert sich der Strom ohne das mehr Leistung aus der Batterie oder ähnlich kommt.
Мощность на выходе всегда, ВСЕГДА ниже потребляемой. Мощность в 2000 вт означает что при напряжении питания в 12 вольт ток питания около 160 ампер. Провода, которыми подключили схему сгорели бы в три секунды! Они выдерживают 10 ампер и то кратковременно. Значит мощность не более 100 вт. Кто сомневается проверьте максимальныцъй ток транзисторов.
Hola buenas tardes, tenía una pequeña consulta, los cables de color azul y los que saca del centro del Mosfet, que numero de cable son? Se los agradecería muchísimo 🙏
2 кВт на 12 вольтах - примерно 200 Ампер. Забавно посмотреть на бедолагу, у которого все эти сопли расползутся в руках после нескольких минут работы 🤣 UPD - Я понял! Этот тип прочел в даташите рабочие параметры транзисторов и решил, что его подпихуйка разовьет именно эту мощность! Куплю на лето шины от Порша. У меня бибика и так шустрая, а с такими ваще полетит!
can you explain to me where you got this 2 kilowatts from ? heat heats but 2KW from 12v power supply is about 160 A and that's without losses , those wires what you show is half a second and they will evaporate .
Eline sağlık Zafer hocam. Yabancıların yorumu bizlerden fazla üzülüyorum doğrusu. Bir sorum olacaktı bu devre için kaç watt güç kaynağı öneriyorsunuz kaç amper çekiyor?
Ну вот сразу видно минус... надо было 2 радиатора, а не 1... Тогда не пришлось бы подкладывать изолятор существенно уменьшая теплопередачу. И охлаждение было бы намного лучше!
@@ajatsingle1703 Why don’t you cut the criticism and move along to a subject you are able to understand. You sure know how to throw a wet towel on a great project. Move along little boy…..
Falta información... Un tiempo considerable para una "gran película" pero no es útil. Cuánta energía requiere??? Todo está superficial -mente soldado, cuánto duran los soldaduras en puntos críticos en fallar???? Yo soy Gabriel humano en Medellín Colombia. Venga pronto tú Reino celestial señor JSS!!!!
merhaba, ni-cd 3 6v 60mah pili 15v ac zil trafo ile şarj edilir mi? akabinde 15v elektrik kesilince bahsi geçen pil çalışma V 12-15~ çalışma Akımı 1,9A Frekansı 50-60hz olan bobini tetikleme yapar mı? Yapmazsa böyle bir istek için devre yapılır mı? Bu devreyi siz yapar mısınız?
Kolsy gelsin ustam eline saglik internette bi kac sey gordum bu projr ile ilgili arasindan boru grcirip su isitip isitma sistemi yapiyorlar sence bu dogrumu bunu hakkinda video paylasirmisin❤❤
ZAFER YILDZ направи едно видео което да ти вярвам! Всичките ти видеа съм изгледал и нито едно не можах да повярвам. Може да лъжеш приятелите си, но не се излагай с тия видеа. Казвам ти го като професионалин дипломиран инженер.
![BLACK BAG - Official Trailer [HD] - Only in Theaters March 14](http://i.ytimg.com/vi/Du0Xp8WX_7I/mqdefault.jpg)
Thank you! I have a blown unit from China that is similar, but the chips had the numbers sanded off. Mine works great, with Tesla pan cake coils, and can run large Dc motors. Adding capacitors and schottky diodes bridge gets over 378 volts DC output.
Good fun!
( a copper foil output coil was a bad idea)
Cheers Warren
Beautiful job with the vid! I have a hard time believing it can output 2kw though.
You're right. 2000 Watts by 12 Volts are 166 Ampere. The connection with crocodile clips does not even manage 50 amps
@@Didi1.275
yup. and they also cant explain how the number of turns affects the power that will be delivered to the workpiece as its just a transformer reflecting impedances at the square of the turns ratio...
im running one off of 150V, and i can actually get a genuine 2kw.... no clickbait required.
the really interesting part about this?
first...
a g40n60 is an IGBT. and ZVS oscillators dont work with IGBTs...
then theres those diodes. 1n4007? really? at 250khz? a plain old standard 1n4007?
i suspect someones doing a bit of cheating regards their little demonstrations versus what they actually "made".
there is a reason most of my time on YT is now spent simply reporting all these clickbait scam channels with DIY "instructional" BS videos.
Den siste idioten är inte född än...
Hey man, is there a video you can recommend that teaches a bit about the theory and actual construction of this? @@paradiselost9946
Паяльничек бюджетный! 👍
Este circuito se ve mucho en internet, es un oscilador que a la vez es driver ZVS y realmente funciona muy bien. Es obvio que ni de broma obtienes 2kW a 12V pero con el mismo tipo de circuito, otros componentes y mas tensión, nada que no se pueda hacer :P
12 V supply, 2 kilowatts will demand over 160 (!) amps.
No way the clip leads can carry that much current.
Nice idea, but don't believe the 2 kW. For comparison, a car starter motor draws under 100 A at 12 V.
Да конечно чушь... На вход сколько подают? 12 v. при 100% кпд надо 167 А а так 170-180 А. это сварочный ток, который для 10 мм электродов... Там провода 50 мм кв. А тут 1.76 мм кв... ну раз в 10 меньше!
Я измерял ток при заводке машины у меня показал 166 ампер, а не меньше 100 как вы говорите
Bravo! C'est super, car vous donnez les informations ❤👍😄
induction cooker €22 + made of square iron pipes 20*20 mm, welded a square loop 20*20 cm, let water through it, added thermal switches, thermovalves, pressure safety valves, a pump for central heating and with 1000 W I heat an apartment of 100 m2. Added more converter 12-220, 1000W, solar collectors 1500W, battery 12 v 200 A and works
BRAVO! You made a perpetuum mobile!
Need to pull this to bits a little. The 'G40N60 IGBT's are rated at 625 Watts each but not your circuit. The 10K resistors are colour coded for 100K. The green choke is intended for noise supression not as a power inductor (totally different permubility). You can use any size of coil and alter the capacitors so that the resonant frequency is within the range of the IGBT's.
बकवास कर रहा है । गलत प्रचार कर रहा है । कैसे आएंगे 166 एम्पियर करेंट ।
पूरा का पूरा बकवास कर रहा है ।
उम्मिद नहीं थी इससे, ऐसा गलत दिखायेगा
False. Totally false.
How and from where you are drawing 166 Amp current ?
Have you any reply.
So stop showing such false sense.
The 10k resistors are colour-coded correctly. The common mode choke he's using as a saturable centre-tapped inductor is demonstrably suitable - it has a high permeability core. It determines the switching frequency to a large extent.
Wrong.
Brown Black Orange for 10k, he is using 100k Brown Black Yellow. Learn your magnetics. @@malectric
Sérieusement j'ai cherché fatiguer 😅mais tu m'a éclairé merci beaucoup 🎉❤❤❤🙏🙏🙏🙏
It's very nice to look at your work. Thanks for the wiring diagram.
बकवास कर रहा है । गलत प्रचार कर रहा है । कैसे आएंगे 166 एम्पियर करेंट ।
पूरा का पूरा बकवास कर रहा है ।
उम्मिद नहीं थी इससे, ऐसा गलत दिखायेगा
2,000 watts at 12VDC equals 166 amps !!! And you use cheap thin clip leads. LOL to the max.
No, this circuit can output more than 60V and 200A across the coil when running it at full power due to resonance
बकवास कर रहा है । गलत प्रचार कर रहा है । कैसे आएंगे 166 एम्पियर करेंट ।
पूरा का पूरा बकवास कर रहा है ।
उम्मिद नहीं थी इससे, ऐसा गलत दिखायेगा ।
False. Totally false.
How and from where you are drawing 166 Amp current ?
Have you any reply.
So stop showing such false sense.
@@ajatsingle1703 well, believe me or not but if you put an AC signal into a resonance circuit with the exact frequency, the voltage and current across a resonance circuit will rises to infinity if there no resistance
This circuit works like an pendulum and 2 mosfet act like 2 hand pushing it every oscillating cycle
لا
درود..واقعازیباست کارت دوست خوبم.من تازه افتخارآشنایی باشمانسیبم شده.ممنونم🎉🎉🎉
şunların üzerine malzemelerin adınıda yazsanız ne güzel olacak o koyduğunuz sarı şey bantmı mesela ?
Good clear video, al though the coil in the middle being cut in the middle and resoldered a little confusing. 2000W and that blade should go white and melt. A 12v car battery will blow a hacksaw blade in two quite quickly, (as I found out)
Bu devre kullanılabilecek bir devredir. Evet DC gerilimden dolayı 2kW olması imkansız, ancak bu devreye olduğu gibi 110-220 VDC uygulanır ve bobin de su ile soğutulursa 2 kW rahat verir. 1N4007 olmaz diyenlerede şunu söyleyeceğim diodun hızından dolayı MOSFET ler rahat çalışabiliyor. Aksi taktirde miller bölgesine girer girmez mosfet kapanacak ve bir kaç MHz de çalışmaya çalışıp patlayacaktır. Sevgiler saygılar.
درود بر شما . بسیار عالی بود❤❤❤
Hi, where did you get 2kw number? If it runs with 12v, current should be almost 170 Amps!!!
Daha güçlü olması için ne yapabiliriz daha fazla isitsin istiyorum ve uzun süreli kullanım yapicam ne tavsiye edersiniz
Nice vedio,However seems incomplete without providing the information regarding the input current / voltage supply.
Zafer bey ellerinize sağlık video larınızı izleyerek yaptığım indüksiyon ısıtıcı ile Erzincan da 2765 watt ile kömüre veda ettik sizi severek takip etmeye DEVAM ediyoruz
Kömüre veda ettik derken ne anlamda usta ne yaptığınızı anlatırmısınız rica etsem?
@@muhammetakgoz2996 yaptığımız sistem ile 2750watt saat elektrik ile günde ortalama 8 saat yâni kombi gibi ısıyı yakalayınca sistem kapanıyor sistemdeki su 10 derece soğuyunca tekrar çalışıyor bu şekilde kömürün her türlü derdinden kurtulduk
Rüzgar gülünden elektirik alırsan bedavaya ısınırsın ama sessiz yap malum vergi kaçırdın diyip içeri almasınlar :) Bu diğer videolarda ki gibi demir boruyu indiksiyon bobinin içinden geçiriyorlar o şekilde ısıtıyor değilmi?
Kaç amp. Çekiyor
i can not see how much amperes it takes, i have ebay 12v/120w inductive heater and it works ok but it is to weak for my need, if it would be double power it would be nice
سلام بسیار ،ممنون❤❤❤
Can i use Z44n instead 40n60?
Übrigens , Leistung ist Spannung * Strom. Wenn die Spannung grösser wird verringert sich der Strom ohne das mehr Leistung aus der Batterie oder ähnlich kommt.
Güç kaynağı yapımı gelsinnn❤
👌
Nice video
Jazakallah for information
Abi herhangi mosfeten yapılıyormu🤔
Boa noite ,só serve para materiais ferrosos ou conseguiria montar um pra p.v.c por exemplo
Thank you!
Is it possible to wind an induction coil with a diameter of 10 - 15 centimeters to boil water?
Beautiful video ...
Whats the least resistance that you can use like i know you can use 190 ohm to 240 ohm resistors but whats the least and max for the 20 ohm resistor
Мощность на выходе всегда, ВСЕГДА ниже потребляемой. Мощность в 2000 вт означает что при напряжении питания в 12 вольт ток питания около 160 ампер. Провода, которыми подключили схему сгорели бы в три секунды! Они выдерживают 10 ампер и то кратковременно. Значит мощность не более 100 вт. Кто сомневается проверьте максимальныцъй ток транзисторов.
Люблю на заграничных видео читать русские комментарии. Русские парни как всегда правы
да это такой же балабол как и индийцы. только этот по изделиям не балаболит :D реально собирает рабочие схемы.
Zafer Bey
İndiksiyon cihazından
Poşet Ağzı yapıştırma cihazı yapılırmı
i am your regular viewer
Thank you for your comment and support.
@@ZAFERYILDIZ52 ❤
Отличная работа друг!
Did you connected the inductor in series or parallel ?
Good
IExcellent job done
Super Video Sir Amazing ❤️
👉❤👈👌
Hola buenas tardes, tenía una pequeña consulta, los cables de color azul y los que saca del centro del Mosfet, que numero de cable son? Se los agradecería muchísimo 🙏
Make video of variables frequency drive for solar to run 3 phase motor
12 volts, how many amps?
kindly provide the green choke details or where can i find one
How may find that smoothing coil😢
سلام.دوست عزیز برای بخاری کامیون درزمان خواب شب بابرق24ولتDCمیشود چنین بخاری ساخت؟
2 кВт на 12 вольтах - примерно 200 Ампер. Забавно посмотреть на бедолагу, у которого все эти сопли расползутся в руках после нескольких минут работы 🤣
UPD - Я понял! Этот тип прочел в даташите рабочие параметры транзисторов и решил, что его подпихуйка разовьет именно эту мощность!
Куплю на лето шины от Порша. У меня бибика и так шустрая, а с такими ваще полетит!
capacitor has 0,33uH ??????
Teşekkürler Zafer bey
Ben Teşekkür Ederim Ziya Bey
greta sharing
Уто-нибуть подскажите: он использует диоды или стабилитроны?
в энергосберегайку загляни, найдёшь на входе детальки, схемку только не собирай, там мощи 20 киловатт, весь подъезд сожжешь)))
can you explain to me where you got this 2 kilowatts from ?
heat heats but 2KW from 12v power supply is about 160 A and that's without losses , those wires what you show is half a second and they will evaporate .
40N60, IGBT N-CH 600V 40A
Its pulsed 2kW. Not continuous.
Eline sağlık Zafer hocam. Yabancıların yorumu bizlerden fazla üzülüyorum doğrusu. Bir sorum olacaktı bu devre için kaç watt güç kaynağı öneriyorsunuz kaç amper çekiyor?
12 volt icin 10 amper yeterli olacaktır ancak daha yüksek voltajlara da dayanacaktir
bu değer de kondansatör bulamıyorum da alternatif önere bilir misiniz hocam? @@ZAFERYILDIZ52
2000 watt ???
12voltta bu akıma dayanacak parça yok şemada
RV compressor free absorption refrigeration heat source ?
Prespá csillám lemez helyett
Tôi vẫn chưa hiểu cái mạch này lại diode ở tần số thấp mà không phải là diode ở tần số cao nhỉ
Diod fast
عمل رائع وجميل هل يمكن ايضاً استخدامها كطباخ تحريضي باستبدالها بملف سخان تحريضي. وشكراً لك
نعم يمكنك استخدامها
12 v how much amp power supply we need
8 amps and above are sufficient
@@ZAFERYILDIZ52 Thats only 96 Watts. So its being pulsed 2kW. Not continuous. Theoretically you could also make pulsed 100kW. misleading title.
बकवास कर रहा है । गलत प्रचार कर रहा है । कैसे आएंगे 166 एम्पियर करेंट ।
पूरा का पूरा बकवास कर रहा है ।
उम्मिद नहीं थी इससे, ऐसा गलत दिखायेगा
Sargi icine demir su borusu koyduk mu su kaynaticimiz hazir ❤
kesinlikle kardeşim
مرسی
Ну вот сразу видно минус... надо было 2 радиатора, а не 1... Тогда не пришлось бы подкладывать изолятор существенно уменьшая теплопередачу. И охлаждение было бы намного лучше!
А блок питания 2kW для него почему не показал?
At 2kw this circuit will draw 170 amps. The device would have to be powered by a car battery. Wires and connections are nowhere big enough.
Çokgüzel bir devre eline sağlık👍👍
güzel yorumun ve desteğin için ben teşekkür ederim
Sağol abi😊
@@ZAFERYILDIZ52 je réponds ou trouve t ont le papier jaune que l'ont peut voir dans votre vidéo en vous remerciant !
Can you touch this copper coil, does it have current, is it dangerous?
Completely safe
Reacts only to metal
Что произойдет на практике, если вместо двух конденсаторов будет пять?
merhaba kondansatör sayısını arttırmanın faydası olur mu
Evet
Классная штука.. А какими биполярными советскими транзисторами можно заменить оригинал?
Он тебе не поможет, он из Турции. Аналоги ищи по даташитам.
Нужны полевые транзюки, биполярные увы, не в теме. И да, ищи по даташитам.
Что-то непонятно чем он запитал эту схему
КТ315, естественно.
@@EmmetPhD мп37 но лучше на мп42 они мощнее но на них надо 2 кроны .
Hi Thanks , Can we use this as a water heater coil ?? if so describe how it can be done plz 🤔
बकवास कर रहा है । गलत प्रचार कर रहा है । कैसे आएंगे 166 एम्पियर करेंट ।
पूरा का पूरा बकवास कर रहा है ।
उम्मिद नहीं थी इससे, ऐसा गलत दिखायेगा
False. Totally false.
How and from where you are drawing 166 Amp current ?
Have you any reply.
So stop showing such false sense.
False. Totally false.
How and from where you are drawing 166 Amp current ?
Have you any reply.
So stop showing such false sense.
@@ajatsingle1703
Why don’t you cut the criticism and move along to a subject you are able to understand. You sure know how to throw a wet towel on a great project. Move along little boy…..
Zafer bey hazır boyle sıstem satıyormusunuz
Сечение обмотки нагревательного элемента значительно влияет на вашу схему!!!???
Як завжди - дуже ПОТУЖНО! Головне наочно і зрозуміло 👍. Маєш руки обценьки 😮, як не опік пальці, тримаючи розжарене, до червоного, лезо? 😂
Залишила поки не прогрілося :)
bobinden geçen akım nedir acaba
Проблема не в том, как сделать двухкиловаттный индукционник, а в том, как сделать к нему блок питания.
Ну как вариант переделать старый сварочный полуавтомат.
Спасибо
24 v ac akim trafosu indiksiyon isiticiyi calistirimi
Brother ,pls make a speed counter motion sensor🥺🤔
yeah i need this
@@New-From-Innovation-Invention you'er right😅
IRF BE30 MOSFET ANY PROJECT PLEASE SIR
Ben bu devreyi irf3205 ile yaptım calismadi neden olabilir
irf ile yapmışsın işte
Он делает это так медленно, и под музыку для эротических фильмов, я думал, сейчас выйдут девочки и будут раздеваться. 😂😂
Ну сколько он выдаст? Ватт 100-150 вряд ли больше...
Thanks
Wire guage of 100 uh👍
Питание от чего?
Yes there are all three kilowatts.
Preciso um com potência pra espiral de 25cm de diâmetro
если нагреватель мощностью 2 кВт питается от 12 В - тогда ток должен быть 167 А - и этот ток протекает через "крокодильчики" ?
ха-ха - 3 раза...
Falta información... Un tiempo considerable para una "gran película" pero no es útil. Cuánta energía requiere??? Todo está superficial -mente soldado, cuánto duran los soldaduras en puntos críticos en fallar???? Yo soy Gabriel humano en Medellín Colombia.
Venga pronto tú Reino celestial señor JSS!!!!
2 KW ? this is funny...not real.
KW?????????? 😂😂😂😂😂 kHz!!!!!!!!!!!!!
2kv 100mA😊
2kv 100mA😊
Это китайские 2 квт!
Nice
2kw means two kiwi's? In electronics, I prefer bananas
merhaba,
ni-cd 3 6v 60mah pili 15v ac zil trafo ile şarj edilir mi?
akabinde 15v elektrik kesilince bahsi geçen pil çalışma V 12-15~ çalışma Akımı 1,9A Frekansı 50-60hz olan bobini tetikleme yapar mı?
Yapmazsa böyle bir istek için devre yapılır mı?
Bu devreyi siz yapar mısınız?
frekans çok yüksek. daha fazla kapasitör ekleyerek frekansı 50khz yapabilirsiniz. benzer bi çalışmayı 20 adet kapasitörle yaptım 48khz de çalışıyor.
evet daha çok minimum maaliyet üzeriden devreyi tamamlamayı düşündüm daha çok geliştirmek mümkün minimum parça maks performans
trabalho com tubos de p.v.c e tenho que aquece-los tem alguma sugestão ? corto o cano em chapas
Kolsy gelsin ustam eline saglik internette bi kac sey gordum bu projr ile ilgili arasindan boru grcirip su isitip isitma sistemi yapiyorlar sence bu dogrumu bunu hakkinda video paylasirmisin❤❤
yapılır ancak iyi ayarlanmalı ısıtmanın ve ortama aktarılan ısının iyi ayarlanması gerekiyor
@@ZAFERYILDIZ52 him bunula ilgili video bekliyorum ustam eğer işin yok ise
2kw?
ZAFER YILDZ направи едно видео което да ти вярвам! Всичките ти видеа съм изгледал и нито едно не можах да повярвам. Може да лъжеш приятелите си, но не се излагай с тия видеа. Казвам ти го като професионалин дипломиран инженер.
harika . 2kw neyi ifade ediyor. cektigi akim farkli ise
40N60, IGBT N-CH 600V 40A
100-200W are real, think about that tiny heatsink with a 2kW source LOOL
ทำขายไหมครับพี่อันละเท่าไหร่