You gave THE best cutting tip ever thought up by anyone. Pull the blade out and do a test run. Thank you! Now if I could just figure out to use this stupid thing. 🤣
Good video, with the width limited to the feeder size obviously rolls are 28", does the software limit the length direction seeing it can draw rolls in? I'm looking to do mainly vehicle lettering and logos and some could be up to around 50" x 20" (1275 x 500mm). So much conflicting info on-line, will the software and machine handle that size?
Hey, why not use "area test" to see if the piece of vinyl is big enough? It's faster as "cut now" without blade. With "area test" it rolls the material and slides the blade as much as to what to cut. No need to take the blade holder out, too.
@@1bigimpact area test was new for me, too. Before the Vevor cutter and signmaster I had a Roland cx24 cutter and flexisign software. The signmaster software has some very handy options.
This was very helpful. How about how to fix the paper holder pressure. Mine are creating the crosshatch pattern on my vinyl and not sure which way to go.
Thank very much!I appreciate it.one more question,okay I created a image on the singmaster,I printed it out on printable vinyl and send it to cut but it cut it so bad,it missed the whole picture so how can I cut images with offset too.thank you for taking your time to do a video on my question ☺️
What tips do you have with cutting imported images? I have tested the cut so many times and have not seemed to master the cut right on. I've even done a contour cut and I still can't seem to get the cut right on.
I THINK I JUST CRACKED THE CODE TO THIS! It's amazing that I asked this question and figured it out right after. Knowing where to place the blade is what gets me everytime but I believe I've got it now. I just have to test it out with my sheet of 1" labels to know for sure. :) I'm excited now haha.
ok so i have set up my machine but my cutting settings are 460 for speed & 80 force & the blade keeps going straight thru the paper ive tried 90 100 it still keeps tearing up the paper...
What do you use for pressure? I've adjusted pressure and the blade so many times but it either cuts through, or doesn't cut fully through for a clean cut
so in my opnion the settings are not what dictates that although i thought the same thing at first i found out the real issue was how far the blade sticks out from the holder from the side angle it needs to be barely visible but i will say if you are changing vinyls alll the time it may need to be set differently each time i hope that helps
Hey there great question and thanks for the sub!!!! So as far as that goes you need to make sure its an image that you downloaded to your computer already and once that is done you can right click on your mouse and click import. also in the top task bar there will be an option to import as well. Side note; if its not a vector image file you will need to convert it before cutting that image to make it look nice! heres the one i use ! www.vectorization.org/ i am not affiliated with this company in any way.
Hi! I just got this for work and the software it comes with won't let me do anything unless I pay for a subscription.... I didn't see this noted anywhere when buying it, is this true for you as well? Did you have to purchase to have access to the software or were you able to download it and then just use it? Also, did it come with a jump drive in addition to the CD? Something about it feels very odd.
I do believe it did and I don't remember what it was for exactly but or exactly but just insert the CD or the jump drive and the product code should be inside the cd case on a yellow piece of sticky
Hi, I have the Vevor but I cant open the signmaster files on my macbook pro. I submitted my PSN number on the signmaster site, they gave me the file to download but can't download the exe file. Any suggestions? BTW, love your video.
@@1bigimpact one more question , do you have an anti static mat under your machine ? Mine is in a wooden floor so I don’t know if it makes a difference or not
IN ALL HONESTY I CHANGE THE SPPED AND FORCE MANY TIME AND IN THE END IT HAD NOTHING TO DO WITH ANYTHING I FOUND THE DEPTH OF THE NEEDLE IS FAR MORE IMPORTNT
Why are you cutting it like that, flip it over so your not cutting through the backing and mirror the image, you are doing that 1000% ass backwards and making it harder on yourself
You gave THE best cutting tip ever thought up by anyone. Pull the blade out and do a test run. Thank you! Now if I could just figure out to use this stupid thing. 🤣
I think the area test function in Sign Master traces a rectangle over the cut area.
Good video, with the width limited to the feeder size obviously rolls are 28", does the software limit the length direction seeing it can draw rolls in? I'm looking to do mainly vehicle lettering and logos and some could be up to around 50" x 20" (1275 x 500mm). So much conflicting info on-line, will the software and machine handle that size?
Yes I did a big logo for the back of my truck window you can do pretty big logos
Great tip pulling the blade out , thanks
Thank you so much for responding to that I appreciate the kindness I hope you make amazing things
Hey, why not use "area test" to see if the piece of vinyl is big enough? It's faster as "cut now" without blade. With "area test" it rolls the material and slides the blade as much as to what to cut. No need to take the blade holder out, too.
Awesome you just taught me something new I'll check it out thanks for the tip I appreciate you
@@1bigimpact area test was new for me, too. Before the Vevor cutter and signmaster I had a Roland cx24 cutter and flexisign software.
The signmaster software has some very handy options.
This was very helpful. How about how to fix the paper holder pressure. Mine are creating the crosshatch pattern on my vinyl and not sure which way to go.
I will definitely make a video on that thank you so much for the kindness I appreciate you please subscribe
The force is how much pressure
thanks soo much for this.. please do one on setting blade and depth 😩
i will 100% make a video very soon for this!!!!
thats been my issue as well,,, im waisting paper
My vevor 375 doesn't move when switched on. The red reset button is on but not movement . Any idea?
Maybe Check the fuse
Do you know how to calibrated the precision of the machine like to make sure the distance are good ? (alignement)
Thanks for making these videos. How we’re you able to lower the rollers, mine aren’t going down by themselves.
That's a great question I will make a video very soon about this please subscribe
Hello ,thank you for your video, i have a question , i have a vevor 135cm but it can't cut the 135 cm it gos only till 72 cm., i dont know why?
Awesome! Thanks for this video!
Glad you liked it! please subscribe!!!!!
Thank very much!I appreciate it.one more question,okay I created a image on the singmaster,I printed it out on printable vinyl and send it to cut but it cut it so bad,it missed the whole picture so how can I cut images with offset too.thank you for taking your time to do a video on my question ☺️
No problem are you dealing with a vector file or did you just take some random image off the Internet
@@1bigimpact picture from the internet..it's a big sunflower like 13"x15 image.and also for the sublimation image too is a 13"&19" size.
did you cut the picture?
Can you do a tutorial on reversing the image? For some reason no matter what I do I keep messing mine up.
I absolutely will in about 30 minutes
What tips do you have with cutting imported images? I have tested the cut so many times and have not seemed to master the cut right on. I've even done a contour cut and I still can't seem to get the cut right on.
I THINK I JUST CRACKED THE CODE TO THIS! It's amazing that I asked this question and figured it out right after. Knowing where to place the blade is what gets me everytime but I believe I've got it now. I just have to test it out with my sheet of 1" labels to know for sure. :) I'm excited now haha.
lol if you just keeep pushing you will figure it out i have other videos explaining this too!!!! thank you for the support you rock
ok so i have set up my machine but my cutting settings are 460 for speed & 80 force & the blade keeps going straight thru the paper ive tried 90 100 it still keeps tearing up the paper...
Lower the force. I run mine at 30.
Hey, appreciate video. How do you remove weed box??
here you go! please subscribe
Great video. I am getting tread marks on my vinyl sheet. What is causing this and can I prevent this from occurring again?
you may try loosining the clamps that hold the material
@@1bigimpact thank you I'll give it a go👌🏽
how do you vetorize images
Just type in online vectorize Imager
What do you use for pressure? I've adjusted pressure and the blade so many times but it either cuts through, or doesn't cut fully through for a clean cut
so in my opnion the settings are not what dictates that although i thought the same thing at first i found out the real issue was how far the blade sticks out from the holder from the side angle it needs to be barely visible but i will say if you are changing vinyls alll the time it may need to be set differently each time i hope that helps
I just received my cutter and heat press roughly a week ago. How do you bring the image onto the software and then transfer it to the cutter?
Hey there great question and thanks for the sub!!!!
So as far as that goes you need to make sure its an image that you downloaded to your computer already and once that is done you can right click on your mouse and click import. also in the top task bar there will be an option to import as well.
Side note; if its not a vector image file you will need to convert it before cutting that image to make it look nice!
heres the one i use !
www.vectorization.org/
i am not affiliated with this company in any way.
Hi! I just got this for work and the software it comes with won't let me do anything unless I pay for a subscription.... I didn't see this noted anywhere when buying it, is this true for you as well? Did you have to purchase to have access to the software or were you able to download it and then just use it? Also, did it come with a jump drive in addition to the CD? Something about it feels very odd.
I do believe it did and I don't remember what it was for exactly but or exactly but just insert the CD or the jump drive and the product code should be inside the cd case on a yellow piece of sticky
Hi, I have the Vevor but I cant open the signmaster files on my macbook pro. I submitted my PSN number on the signmaster site, they gave me the file to download but can't download the exe file. Any suggestions? BTW, love your video.
signmaster only works on windows computers
Ciao ,avrei biaogno di aiuto ,il mio plotter manda il vinile tutto fuori sensa fermarsi
Hi, when I get ready to cut it doesn't show the actual size in preview. How can I make sure it will cut the correct size
hey there, do whats callled a dry run take the needle out and load the vinyl and let it run the cut to make sure it will be ok
Where do you buy vinyl that’s wide, say around 30 inches? Dies anybody know ??
amzn.to/3zt0iX3
How do you import designs? Everytime I import a design of mine it doesn’t show when I’m about to cut it
do view wirefram mode
How do I put the needle in
ruclips.net/video/hgaKDwa4yu0/видео.html
I lost my code to start up the machine..how do I get the code?
You should be able to email the company
Which vinyl are you using for the t shirts ??
Great question give me just 1 second and I'll post a link for you
amzn.to/3JYRUn3
@@1bigimpact one more question , do you have an anti static mat under your machine ? Mine is in a wooden floor so I don’t know if it makes a difference or not
What speed and force do you use? Also what is +6vale and baud 9600 mean?
IN ALL HONESTY I CHANGE THE SPPED AND FORCE MANY TIME AND IN THE END IT HAD NOTHING TO DO WITH ANYTHING I FOUND THE DEPTH OF THE NEEDLE IS FAR MORE IMPORTNT
Hi have the same plotter but Vevor sent me the wrong drivers with the Signmaster software. Can you please help me? I need the KH-720 ones
hi there i would just google the free driver and im sure you will find the one you need!!!! thanks for the comment
@@1bigimpact I’m searching them since last december. Found nothing…Neither assistance. If you can help me it will save me
Can anyone explain how to change the language settings from Chinese to English on the vevor cutter?
there should be an options button!!!!
Why are you putting the vinyl in face down?
because the shiny part is called the carrier (clear plastic) and you dont cut that part
mine keeps saying nothing to cut :(
when you go to print preview are you seeing the image you want to print
@@1bigimpact yes but just found out i have to upgrade to pro to be able to use the vinyl cutter
:(
@@1bigimpact can it cut tints
@@amandaturner60 what software are you using? I have the basic signmaster cut software and it works with the vevor cutter.
Why are you cutting it like that, flip it over so your not cutting through the backing and mirror the image, you are doing that 1000% ass backwards and making it harder on yourself