Finally got the tools, is torque wrench required? I'm not confident about tightening. Also do i have to open axle nut to remove strut(spring compressor not available, will be taking strut outside to disassemble). Is fitting axle back going to be problematic for first timer
Sir no need of removing axle , and sir Torque wrench is not needed , you can do it just by feel . And on a scale of 1-10 , changing a strut is like 4 . But spring compressor is necessary , without it you will not be able to assemble it back , as springs will expand
It's better to use a plier to remove the Wire Holding Clip. Personal experience 😅 and did you not have to counterhold the Stabiliser Rod nut? And what exactly is an indicator of a failing Top Mount that we should be watchful about?
Anti roll bar nut was easy for me as the inner section did not moved , and the sign is lack of sure footedness on higher speeds like 100+ , you can feel the car bouncing a little , as my atruts are not yet completly shot , they still have resistance. Maybe that was the reason i was not ready with the part
Hi. Was this the factory fitted Shocker which you replaced? There are two options available for shockers: One is 6RF 413 031 G which is Made in India and costing around 1950 while the other is 6R0 413 031 AJ, which is Made in Germany and costs around 4000. The build quality is significantly better in the latter. Which one to go?
Sir i order all my parts from a offline supplier, he deals in Volkswagen, skoda and audi spares . He is in it from 20+ years, and i never got a wrong part
Hey! I intend to experiment with installing Ciaz or Brezza's Suspension Coil Springs in my Vento TDi just to experience a softer ride. Your thoughts on this?
Sir coils installed as per the weight and weight distribution on front and rear axles , if brezza or ciaz is heavier than vento , then you are going to experience more stiffness , and if lighter than more softness .
@@yourDIYneeds I want the ride to be as softer as possible. As a fact, Ciaz and Brezza weigh lower than Vento & their Spring Rating is also low (Softer). Considering this would you recommend experimenting? And will the Coil Spring of Ciaz accommodate on Vento's struts. (I guess it should)
Sir that totally depends upon the diameter current and new springs , If brezza and ciaz is lighter that ideally ride should be softer , but we also have to keep in mind that weight distribution also pays an important role , you can go for it , if if turns out to be good , let me know too .
Really informative........What can be stimated cost for replacement of front and rear suspensions of vento petrol 2010 model......including both lower arm.....Thanks in advance
Can GABRIEL suspension mount be used instead of the OEM? OR any other aftermarket brand which is on par with the OEM? And also does little wearing-out of the mount cause One-sided shoulder tire wear?
Sir lemforder are good , you can use those instead of OEM if you want . Mount wear doesn't result in shoulder wear , thats most of the time improper alignment .
@@yourDIYneeds Thanks much on your perspective. What is the recommended Kms threshold to change the Suspension mounts (if any) OR to be changed only on the symptom of wear-out?
Sir basically it depends upon the running condition , environment in which you drive , condition of the roads . Needs a check or atleast need to lookout for symptoms before replacing anything , but yes a rough estimate is close to 80-90k kms is like the time to change suspension components
No advantages of using ceramic in our vehicles , because its not designed for ceramic , system is designed for semi metallic brake pads and only those will perform best , ceramic needs to warm up before they can provide full braking power , and also have a tendency to make high pitch noise .
Thanks bro .. one doubt..In my rapid there was a tik tik noise generated while turning steering wheel and steering was quite heavy . we dismantled the strut , cleaned , lubricated the strut bearing , changed the top rubber mount and cap. For few months , it was fine . Again it came. Now the steering is super tight and noise also. Technician says the strut bearing may be damaged as the steering system seems ok.. .Whether above steering issues happens due to strut bearing? Car is Rapid 1.5 TDI , diesel, 2015 ... Thanks for your time and effort..
Sir usually bearing just needs new lubrication after few years , but if the bearing has developed grooves then you have to change the bearing , its not that expensive
@@yourDIYneeds bro i search front shock absover for my skoda laura in boodmo they are show me price of each one is sachs is 14k monroe is 5200 VAG is 9k bilstein is 10k and meyle cost is 5500
Sir sachs are OEM suppliers for European market , thats why they are the most expensive , in india mostly its Gabriel which is providing the shocks , and all others are aftermarket , but these brands also have different models and varients for shocks , which will also effect the price , bilstein can be a nice option , they have good name for aftermarket but can't say much about oem parts
Sir firstly iam happy for having videos on Vw and front shock part 6RF 413 031 C as given by you can I use 6RF413031 F part also? In 1.2 petrol 2013 model
I changed the front shocks thats ending with F and the car doesn't feel okay...seems like front heavy and bottoms out with even single person in the vehicle at low speeds...is it because of the suspension part?
Sir you can go for "gabriel" shocks they are a combo or handling and comfort , for shock top mounts , go for "lemforder" Half the price but same quality. And for steering tie rods and their ends , you can go for "stark" good quality and durability. Hope it helps 👍
I haven't removed the sensor bro , check , And not just for abs sensor We should ideally remove the -ve of battery before any work , to protect it from shorting out
I have a polo tdi 1.5 and having a problem with my front coil springs or shockers , it is making a SQUEAKING SOUND while turning the car while driving or while parking my car . Just replaced my front wheel bearing but the sound seems to increase day by day. Please suggest ???
@@yourDIYneeds there is a whole confusion about front struts for polo… i checked at service center also and they said its normal for piston to not to come up ..they had 2 front strut and one of them was returning back upwards and other one was not …i have heard from others as well that its normal for shock absorbers for polo to not to come up.
Sir polo and vento comes with low pressure struts , which means they have pressure but not as compared to some other shocks . Pressure is there just to prevent the foaming of strut oil . When new they usually return at a very slow speed but as they age strut starts to wear , and something it comes back but sometimes it doesn't Just make sure they both should behave the same
URGENT Bhaiya maine front shokar order kiye the (6RF413031G) lekin woh bhaut smooth hai mujhe laga kharab hai toh maine replace Kara ke dusre manga liye lekin woh bhi wase hi hai koi leak nahi hai . Kya yeh smooth hote hai Ab mein kya karu monore ke shokar kaise hai please suggest
Hi Sir I have Vw ameo petrol 1.2 L font suspension make noise when i drive on potholes in high speed. Can you please tell me what would be the problem.
I tighten it with wrench pretty well , i don't have a torque wrench at this point, and bolt is designed that it has a warcel thick layer of thread lock , when you ll open it , you can feel it
My wolkswagen polo 1.2 petrol car water pump belt noise is coming when im putting sama powder noise be stop again morning come noise. Please tell me what to do sir
Not considered a problem , untill unless its doing any changes in the way , how car drives , but yes will make some grinding noise , which may or may not be audible due to body on chassis construction
Hi Sir,can you make a video about draining/changing assy.sedimenter placed left side of fuel tank.Lots of viewers even don't know that Tata Safari/other cars have something called as pre filter/sedimenter.It wil help lots of people Sir.
Hi sir, mera Polo 1.5tdi car hai, 38k running hai, showroom me alignment, wheel balance karwayata test drive pe right pulling and steering me vibration aa rahi hai showroom wale bol rahe hai tyre wear out hua hai isle vibration ho raha hai, kucch solution batayiye, pls suggest best tyres for polo 1.5tdi
Check Steering Angle Sensor and you might need to callibrate it. Check tyre pressures and if nothing helps, then checking suspension will be needed. Has steering been changed or opened anytime? While removing sometimes there can be a spline mismatch.
Sir scorpio s10 model hai only 47000km total running hui hai..uska piche ka ek shocker leak ho gya hai ..toh sir mujhe yeh confusion ho raha hai ki mujhe dono shocker hi change karne chaiye ya sirf jo leak hua hai vo hi change karu... ??
@@yourDIYneeds sir gabrial ka shocker acha rahega ya mahindra geniue.....scorpio ke liye gaddi ki running kaam hai lakin photholes or kharab rashto pe hi chalti hai...??
Sir suspension is the complete set of things like shock absorber , lower control arms , ball joints , tie rods and their ends , all together we call them suspension , but shock absorber is just a part of suspension
I’m looking to replace my front shocks on my vento to gas ones.. how is Sachs and Steinerhoff? Koi hai jissne use kia ho.. sachs mil nahi raha hai market main
Sir, sachs ache hai but as such koi major improvement nahi hai OEM se , baki I can't say anything about steinerhoff as nor me or neither anyone i know used them before
@@yourDIYneeds thanks. i bought Borsehung make front shocks finally. Need to install and will see how much difference is there, can u share your number?
Sir no. Is provided by office so i am really not able to share , but you can contact me anytime on my mail everydaydiyhelp@gmail.com Hope your understand 🙂
My car makes a tap tap noise even on smooth roads from left side early in the morning. Once I have driven 10-15kms the noise completely goes away. My area mechanics have changed the whole suspension assembly(suspemsion, lower arm bushes, strut mounts, link rods). No one are able to find out the exact problem what do you think it might be??
Bro mai nay brand new front suspension le k aya hu company se but ek suspension down ja raha hai company mai pucha tho wo bol rahe hai esa he rehta hai kya karu replacement k liye bolu ?
@@yourDIYneeds yes but Volkswagen group now selling 2 types parts one which have low gas & oil which comes under Rs 1875 & second one which comes with fully gas oil fill under Rs 3960 so it's all depends on customer wether they want low maintenance parts OES or original Volkswagen parts OEM
This is the 2nd time I ordered front shock-absorber struts from boodmo for my vento 2012 . But the case is same as of your struts.. going down and not retaining its position. What should I do?
Same was the case with the struts I fitted a couple of months ago and my car's nose dips while braking, bouncy ride ,steering vibrations and sways while turns.
Sir have you changed the rear shocks as well . And nose dive while braking can be a fault of brakes itself . All 4 wheels should brake acc. To the grip a available , but when your front brakes become more catchy than the rear , then you experience nose dive , and shocks just amplify that dive
Sir aap seekh lo ,. Bina shocker khole kaise daloge ? Jab uske upar bolt hai ? Agar vw Ka OEM mount hai to khol ke hi dalega lekin agar Renault wale use kar rahe ho to wo nahi rukenge bolt ke baad bhi 😅😅 , agar aap kaho to worship manual me se illustration ki photo bheju ? And sir I m not even a mechanic 😅
subtitles / closed captions available
Really impressed with ur calmness in the diy👍🙏
Nice video sir. Very detailed information.
Finally got the tools, is torque wrench required? I'm not confident about tightening. Also do i have to open axle nut to remove strut(spring compressor not available, will be taking strut outside to disassemble).
Is fitting axle back going to be problematic for first timer
Sir no need of removing axle , and sir Torque wrench is not needed , you can do it just by feel . And on a scale of 1-10 , changing a strut is like 4 . But spring compressor is necessary , without it you will not be able to assemble it back , as springs will expand
@@yourDIYneeds thanks, I'll get strut assembled from nearby garage, I just have to remove and refit .
It's better to use a plier to remove the Wire Holding Clip. Personal experience 😅 and did you not have to counterhold the Stabiliser Rod nut? And what exactly is an indicator of a failing Top Mount that we should be watchful about?
Anti roll bar nut was easy for me as the inner section did not moved , and the sign is lack of sure footedness on higher speeds like 100+ , you can feel the car bouncing a little , as my atruts are not yet completly shot , they still have resistance. Maybe that was the reason i was not ready with the part
Hi. Was this the factory fitted Shocker which you replaced? There are two options available for shockers: One is 6RF 413 031 G which is Made in India and costing around 1950 while the other is 6R0 413 031 AJ, which is Made in Germany and costs around 4000. The build quality is significantly better in the latter. Which one to go?
Sir that totally depends upon your choice , you can go for any of it as per your budget
Hello Brother, you video is great, need a help, where can we order all the 5 doors rubbers and buffer for bonnet to stop noise.
Sir i order all my parts from a offline supplier, he deals in Volkswagen, skoda and audi spares .
He is in it from 20+ years, and i never got a wrong part
Hey!
I intend to experiment with installing Ciaz or Brezza's Suspension Coil Springs in my Vento TDi just to experience a softer ride. Your thoughts on this?
Sir coils installed as per the weight and weight distribution on front and rear axles , if brezza or ciaz is heavier than vento , then you are going to experience more stiffness , and if lighter than more softness .
@@yourDIYneeds I want the ride to be as softer as possible. As a fact, Ciaz and Brezza weigh lower than Vento & their Spring Rating is also low (Softer). Considering this would you recommend experimenting? And will the Coil Spring of Ciaz accommodate on Vento's struts. (I guess it should)
Sir that totally depends upon the diameter current and new springs ,
If brezza and ciaz is lighter that ideally ride should be softer , but we also have to keep in mind that weight distribution also pays an important role , you can go for it , if if turns out to be good , let me know too .
@@yourDIYneeds Yes! Diameter is the criterian here for the springs to fit & lock at the notch on the Vento's Struts.
Yes sir
excellent content. keep posting.
Really informative........What can be stimated cost for replacement of front and rear suspensions of vento petrol 2010 model......including both lower arm.....Thanks in advance
Sir around 30k including all the OEM parts
i have polo 1.2 tdi,
my car having a issue of both front tyres inner side tyre wear.
what is the problem with them.
First check alignment , if its ok
Then you have problem regarding suspension (specifically lower control arm bushes )
@@yourDIYneeds can you please provide me alignment data photo and lower arms bush.
8901005229 it's my what's app no. i m waiting for your message.
Can GABRIEL suspension mount be used instead of the OEM? OR any other aftermarket brand which is on par with the OEM?
And also does little wearing-out of the mount cause One-sided shoulder tire wear?
Sir lemforder are good , you can use those instead of OEM if you want . Mount wear doesn't result in shoulder wear , thats most of the time improper alignment .
@@yourDIYneeds Thanks much on your perspective.
What is the recommended Kms threshold to change the Suspension mounts (if any) OR to be changed only on the symptom of wear-out?
Sir basically it depends upon the running condition , environment in which you drive , condition of the roads . Needs a check or atleast need to lookout for symptoms before replacing anything , but yes a rough estimate is close to 80-90k kms is like the time to change suspension components
Which front brake pads are you using?
Any suggestions in ceramic pads for vento ?
No advantages of using ceramic in our vehicles , because its not designed for ceramic , system is designed for semi metallic brake pads and only those will perform best , ceramic needs to warm up before they can provide full braking power , and also have a tendency to make high pitch noise .
@@yourDIYneeds okay , then i will go with the oem brake pads only..
Thanks bro .. one doubt..In my rapid there was a tik tik noise generated while turning steering wheel and steering was quite heavy . we dismantled the strut , cleaned , lubricated the strut bearing , changed the top rubber mount and cap. For few months , it was fine . Again it came. Now the steering is super tight and noise also. Technician says the strut bearing may be damaged as the steering system seems ok.. .Whether above steering issues happens due to strut bearing? Car is Rapid 1.5 TDI , diesel, 2015 ...
Thanks for your time and effort..
Sir usually bearing just needs new lubrication after few years , but if the bearing has developed grooves then you have to change the bearing , its not that expensive
Im having same issue i had change with technix brand 😢
Hello 👋 bro I need advice about shocks>
What is best vw alternative aftermarket shock absover brands ????
Sachs or Monroe
@@yourDIYneeds what about MEYLE Brand bro ???
Sir mayle is nice but i guess they are on expensive side
@@yourDIYneeds bro i search front shock absover for my skoda laura in boodmo they are show me price of each one is sachs is 14k monroe is 5200 VAG is 9k bilstein is 10k and meyle cost is 5500
Sir sachs are OEM suppliers for European market , thats why they are the most expensive , in india mostly its Gabriel which is providing the shocks , and all others are aftermarket , but these brands also have different models and varients for shocks , which will also effect the price , bilstein can be a nice option , they have good name for aftermarket but can't say much about oem parts
Sir firstly iam happy for having videos on Vw and front shock part
6RF 413 031 C as given by you can I use 6RF413031 F part also? In 1.2 petrol 2013 model
Yes sir , they are same parts "F" is a newer revision than "C"
Which is the one for diesel polo 2017 is it f or g or c?
I changed the front shocks thats ending with F and the car doesn't feel okay...seems like front heavy and bottoms out with even single person in the vehicle at low speeds...is it because of the suspension part?
Could u pls suggest best mechanic for polo petrol cng in delhi Or noida?
Sir to be true , no recommendation
sir im using a 2017 model polo tdi.my suspension is damaged can you suggest an aftermarket suspension with better comfort and handling balance
Sir you can go for "gabriel" shocks they are a combo or handling and comfort , for shock top mounts , go for "lemforder"
Half the price but same quality.
And for steering tie rods and their ends , you can go for "stark" good quality and durability.
Hope it helps 👍
Thanks a ton!i asked the showroom guys they told me that the whole front suspension system would cost me around 40k is it true ?
😅 at service centre , yes close to that , but i guess they didn't included taxes while giving you quotation. 👍👍
Whatever I’ll try the get the brands that you suggested! Thanks a lot
brother before removing ABS sensor for any job like brake or suspension first pls disconnect -ve terminal. it is safe for sensors.
I haven't removed the sensor bro , check ,
And not just for abs sensor
We should ideally remove the -ve of battery before any work , to protect it from shorting out
yourDIYneeds yupp. Yes, i have mentioned it in last line of my comment ✌️.
Bro for vento 1.6 tdi VW ASC gave an Estimate of Rs 45k for suspension overhaul is it worth or its better to do in FNG
You can get all those things done outside and with the genuine parts , and you will cost you close to 25k for parts
Bhai coupling rod ki cost kya h vw Polo..is there any aftermarket brand available?
Sir , stark , delphi ,trw ,bhot sare brands hai
I have a polo tdi 1.5 and having a problem with my front coil springs or shockers , it is making a SQUEAKING SOUND while turning the car while driving or while parking my car . Just replaced my front wheel bearing but the sound seems to increase day by day. Please suggest ???
Sir its the strut thrust bearing
@yourDIYneeds - thank you sir for the answer and the prompt reply👍. Pray that you prosper in RUclips!
Thanks alot sir 🙂
Did you feel any difference in stability/handling after replacing struts ?
Not after struts but definitely after control arms
@@yourDIYneeds control arms were worn out too ? Or that has to be replaced with strut as well ?
Sir i replaced everything , they were not that worn out but when i was doing everything then it was not a good idea to leave a component
@@yourDIYneeds there is a whole confusion about front struts for polo… i checked at service center also and they said its normal for piston to not to come up ..they had 2 front strut and one of them was returning back upwards and other one was not …i have heard from others as well that its normal for shock absorbers for polo to not to come up.
Sir polo and vento comes with low pressure struts , which means they have pressure but not as compared to some other shocks .
Pressure is there just to prevent the foaming of strut oil .
When new they usually return at a very slow speed but as they age strut starts to wear , and something it comes back but sometimes it doesn't
Just make sure they both should behave the same
URGENT Bhaiya maine front shokar order kiye the (6RF413031G) lekin woh bhaut smooth hai mujhe laga kharab hai toh maine replace Kara ke dusre manga liye lekin woh bhi wase hi hai koi leak nahi hai . Kya yeh smooth hote hai Ab mein kya karu monore ke shokar kaise hai please suggest
Sir OEM smooth hi hai , Monroe bhi ache hai but thode se stiff honge
@@yourDIYneeds bhaiya aap kya suggest karenge I am confused
@@yourDIYneeds bhaiya ball joint RANE company ke theek hai
Oem sir
@@yourDIYneeds bhiya ball joint ka aur bata dete 😊🙏
HI SIR,CAN YOU PLEASE TELL ME THE SIZE OF T WRENCH OR SPANNER USED TO REMOVE TATA SAFARI OIL DRAIN PLUG
24mm
@@yourDIYneeds Thankyou Sir
What is the socket for opening top nut? Thought shallow ring spanner will work, but its not fitting.
Sir its 21mm , ideally there is a speciality tool called strut nut opener in VW which allows the use of a hex key along the 21 mm
@@yourDIYneeds specific name of that type of socket? Searched online but couldn't find, Amazon link will be helpful
www.ubuy.co.in/search/index/view/product/B07JWVWLH1?inf=26c0a195973b46ba52a013c89dd82315&
Sir here it is
@@yourDIYneeds hello sir, what's was the tool(socket type) you used in video. Also need nuts and bolts for rear suspension. Couldn't find them online
amzn.to/3P5qeip
amzn.to/3L8l3ex
These are the link to the tools needed for pendulum mount
Sir which bolts do you need for rear suspension
Hi Sir I have Vw ameo petrol 1.2 L font suspension make noise when i drive on potholes in high speed. Can you please tell me what would be the problem.
Sir its strut top mounts or steering rack ,
I have video on both the topics
Thank you so much for your response sir.
Yeh shocks kahan se milega and how is the quality....are these OEM...?
Yes sir , they are OEM part
You told the nuts and bolts of shockers were thread locked... after reinstalling how much torque u used and did u use a thread locker sir.
I tighten it with wrench pretty well , i don't have a torque wrench at this point, and bolt is designed that it has a warcel thick layer of thread lock , when you ll open it , you can feel it
Ok now I got it
Sir nd piche ki shocks ki boot rubber replacement video kb tk aaegi
My wolkswagen polo 1.2 petrol car water pump belt noise is coming when im putting sama powder noise be stop again morning come noise. Please tell me what to do sir
Sir just replace the belts with tentioner, it will be a long term solution
Hey, can you tell me what tool is required to remove abs sensor.?
Sir as far as i remember its a hex drive h7 .🤔
Sir in Scorpio rear axle outplay and inplay is normal or it has some problem
A bit of wear in half-shaft c-clip or it can also be bearings or diff-gear wearout due to lack of lubrication
Is it on both sides or just one side?
It is ok
Sir please tell this is problem in car or not
It is on both sides but right has littlebit more
Not considered a problem , untill unless its doing any changes in the way , how car drives , but yes will make some grinding noise , which may or may not be audible due to body on chassis construction
Hi Sir,can you make a video about draining/changing assy.sedimenter placed left side of fuel tank.Lots of viewers even don't know that Tata Safari/other cars have something called as pre filter/sedimenter.It wil help lots of people Sir.
Sure sir 👍, it is a good video idea , i get ideas from supporters like you .
Keep that coming !👍👍👍👍👍👍👍
@@yourDIYneeds Welcome Sir.Sorry for the late response.
Hi sir, mera Polo 1.5tdi car hai, 38k running hai, showroom me alignment, wheel balance karwayata test drive pe right pulling and steering me vibration aa rahi hai showroom wale bol rahe hai tyre wear out hua hai isle vibration ho raha hai, kucch solution batayiye, pls suggest best tyres for polo 1.5tdi
Check Steering Angle Sensor and you might need to callibrate it. Check tyre pressures and if nothing helps, then checking suspension will be needed. Has steering been changed or opened anytime? While removing sometimes there can be a spline mismatch.
Sir scorpio s10 model hai only 47000km total running hui hai..uska piche ka ek shocker leak ho gya hai ..toh sir mujhe yeh confusion ho raha hai ki mujhe dono shocker hi change karne chaiye ya sirf jo leak hua hai vo hi change karu... ??
Sir suspension ka koi bi part akela change nahi karte , best practice yehi hai ki ek sath change kiye jae
@@yourDIYneeds sir gabrial ka shocker acha rahega ya mahindra geniue.....scorpio ke liye gaddi ki running kaam hai lakin photholes or kharab rashto pe hi chalti hai...??
Sir gabrial hi shock absorber banata hai most of companies ke lie india me , so jo apko sahi lage wo le lijiye
bro what is the differents between shock absorber and suspension? I m confused shock absorber n suspension looks similar to me.
Sir suspension is the complete set of things like shock absorber , lower control arms , ball joints , tie rods and their ends , all together we call them suspension , but shock absorber is just a part of suspension
@@yourDIYneeds so if I buy suspension than everything will be include like what u mention?
Sir we have to buy everything separate , no kits exist in case of suspension
hi how can i connect with you, need help a lot if you are from Delhi
Yes sir i am from delhi
You can contact me on my Mai everydaydiyhelp@gmail.com
@@yourDIYneeds i post a mail to you please reply as possible
Both Front Shocker mount change karne me kitana time lagata he?
2 hrs
Sir which brand after market shocks r this?
Sir these are OEM
@@yourDIYneeds after market suggestions?
Sir , monrow are good once
I’m looking to replace my front shocks on my vento to gas ones.. how is Sachs and Steinerhoff? Koi hai jissne use kia ho.. sachs mil nahi raha hai market main
Sir, sachs ache hai but as such koi major improvement nahi hai OEM se , baki I can't say anything about steinerhoff as nor me or neither anyone i know used them before
@@yourDIYneeds thanks. i bought Borsehung make front shocks finally. Need to install and will see how much difference is there, can u share your number?
Sir no. Is provided by office so i am really not able to share , but you can contact me anytime on my mail everydaydiyhelp@gmail.com
Hope your understand 🙂
My car makes a tap tap noise even on smooth roads from left side early in the morning. Once I have driven 10-15kms the noise completely goes away. My area mechanics have changed the whole suspension assembly(suspemsion, lower arm bushes, strut mounts, link rods). No one are able to find out the exact problem what do you think it might be??
Sir check , maybe your link rod is touching the inner fender liner , on bumps , happened with me as well on cold morning and i found out after 2 yrs
Bro mai nay brand new front suspension le k aya hu company se but ek suspension down ja raha hai company mai pucha tho wo bol rahe hai esa he rehta hai kya karu replacement k liye bolu ?
Ek down hai ?
@@yourDIYneeds ha ek Jada down ho raha hai up kam a raha h company vale bol rahe h ese he ata hai
Aur doosra wala return up aa raha hai ?
Sir ideally dono equal hone chaiye
@@yourDIYneeds yes but Volkswagen group now selling 2 types parts one which have low gas & oil which comes under Rs 1875 & second one which comes with fully gas oil fill under Rs 3960 so it's all depends on customer wether they want low maintenance parts OES or original Volkswagen parts OEM
How much will it cost to replace both front suspension kits bruh? Mine are gone💀
Bhai please help me meri vento m all 4 wheel Tyre wear ho rha hai please help me...
Get the bushings check
Bro vw polo both front suspension replacement cost ????
Sir front shocks- 1750/pc
Shock mounts - 1300/pc
Sway bar bushes - 600/set of 2
End links - 2600/set
Guide ball joint - 768/pc
Control arm- 1920/pc
Retainer cap and bearing?
Sir safari dicor me idle rpm unstable rehta hai up down hota rehta hai .. koi solution?
Sir sabse pehle MAF sensor clean hoga
Agar uske baad bhi nahi hui normal then hume scan karke cam and crank sensor ko dekhna padega
yourDIYneeds maf sensor clean krwaya tha
Then sir cam and crank sensor check , and also look for vaccume leaks , they can also effect the idle
This is the 2nd time I ordered front shock-absorber struts from boodmo for my vento 2012 . But the case is same as of your struts.. going down and not retaining its position. What should I do?
Sir after a time it happens , normal ageing
Same was the case with the struts I fitted a couple of months ago and my car's nose dips while braking, bouncy ride ,steering vibrations and sways while turns.
So is it okay to not return these ?
Sir have you changed the rear shocks as well .
And nose dive while braking can be a fault of brakes itself .
All 4 wheels should brake acc. To the grip a available , but when your front brakes become more catchy than the rear , then you experience nose dive , and shocks just amplify that dive
And if it sways then have a look at the sway bar links and bushes and top mount as well
Kitna cost huwa, sab milaake ?
Sir around 7-8 ke aas paas tha
Bro kitne km chali hai car .
Car to new lag rahi hai phir itni jaldi suspension khrab ho geya
67000 kms and 5.5 yrs old
sir pls send me address for bangalore change vento suspension
Rear shock kese open krna hi sir wha jagah kam hi
Sir kal raat ko hi change kie hai , video edit karke post kar dunga 2-3 din tak
Hii
From Gujarat
Hello sir
@@yourDIYneeds I wnat to talk with you sir.
Uno minda ke shocker kaise hai?
Sir for polo ?
@@yourDIYneeds no i have honda city but i want to know minda shocker quality?
Sir best is to go for munjal shova for honda ( if available ) if not , then you can go for monroe or gabrial
@@yourDIYneeds any place or website where munjal showa suspension available?
Sir you have to find it offline , i guess online will be a little difficult
Its OK because the behaviour of shock absorber without gas filled type acts like this ... when u r pulling their be resistances.
Sir they are low pressure struts , they are supposed to be equal on both ends , but they were not at that point in time
And part number for shockers?
6RF 413 031 C
@@yourDIYneeds ok thanks
Tough to hai sir thoda.. experience rhna chye
Machnics ji ye mount bina shocker khole bhe pad jata h kyon pagal pan ke video bana rahe ho phale achhe se seek lo
Sir aap seekh lo ,. Bina shocker khole kaise daloge ? Jab uske upar bolt hai ?
Agar vw Ka OEM mount hai to khol ke hi dalega lekin agar Renault wale use kar rahe ho to wo nahi rukenge bolt ke baad bhi 😅😅 , agar aap kaho to worship manual me se illustration ki photo bheju ?
And sir I m not even a mechanic 😅