Видео

This video help me a lot, thank you 🙏

Hello, I have a Mazda 2 1.3Lt FROM 2009 and every day when I start the engine it gets cold, the engine shakes enormously for the first 15 minutes then the engine runs normally, later the engine actually runs at low speed. I have already replaced the spark plugs, replaced the throttle body, cleaned the air mass sensor, changed the valve oil control sensor, air filter, cleaned and checked the injector nozzles. The car has 181,457km on it, I also cleaned the oxygen sensor and nothing. I don't know if they will be PCV or EGR valves. I don't know what any help would be helpful. Thanks

hello sir, I need help please, I have a car like Mazda 2 from 2009 1.3L and every morning when I start it the engine shakes for the first 10 minutes, after the temperature becomes normal and for the rest of the day the Even if the car is turned off and restarted, nothing else happens. The next day, when I start the engine again for the first few minutes, it shakes a lot. Do you know what the error is?

Some people just should not post videos telling others how to fix anything, and you are one of those people. Every step has to be followed. They are all necessary in completeing the job properly. You obviously don't have a clue about working on cars and probably had overheating issues with this car afterwards. You don't sound confident with yourself and the work you are doing to this car. NO WAY IN HELL WOULD I FOLLOW YOUR ADVICE FOR FIXING ANYTHING. Stop misleading people with hack-job videos.

Is there any place where I can get these pictures?

Jel je iko menjao knock senzor na Mazda 2 1.3 benzinac? Znam da na vecinom Japanaca traze da budu original senzori pa kad stavis aftermarket ne odgovara. Pa pitam jel moze na taj auto aftermarket ili ipak mora original knock senzor? Hvala

Thankyou

Terrible design by mazda. There's no room on the left side to do anything.

Where is the PVC valve on these. I think it is behind the Intake manifold. Requires the whole intake manifold to be removed?

Pvc valve?

god bless u

Greetings, thank you. I've found your videos very useful. I have a question, I have a Mazda 2 DY, with the 1.5L ZY-VE motor. I am wanting to be able to clean the MAP sensor but it seems to be positioned on the intake manifold in such a way that makes it impossible to remove the sensor easily. How can it be removed to be able to be cleaned ? Any help would be much appreciated. Thank you so much

Thanks for the video. Stumbled on it randomly after looking for knock sensor problems, but it turns out, I changed the coolant the day before following the mazda procedure. The blind cap was a very hard to remove, used some pry tool and both fingers to push it from under. Would have been easier by removing the air filter case. So mazda did not tell us to put temp to max, but do a engine revving at 2500RPM for like forever. Only did one cycle and coolant never moved. Driven the car to work and back, 30km. After the video, I went to check the coolant reserve and it was almost empty! Filled it back to full and I guess I'm close to 5.1L for the MTX. Will check again after another ride to work. No overheating ever happened.

Is it hard to remove the inlet to get to the knock sensor ??

Terrible videoing

Pcv valve location?

I need to know how to replace ks on mx5 2007

Where is the fuel filter on this car I have Mazda 1.5 dynamic 2007 model can't find it .

mine is saying snow all the time on a 2.0 turbo, doing the same your doing good vid

Hi nice description on the PCV valve. I think my mazda 2 has blow by. When i open the oil cap during idle there is a lot of air pushing out but if i remove the dip stick theres no air pushing out there. There is also no smoke. Could this be my PCV valve? Or is this just normal?

Seems Mazda or Ford is keeping some information hidden.

Very useful video 👍🏻👍🏻👍🏻👍🏻

Where is the power steering fluid tank?

sometimes i watch this video to relax

where is the PCV valve?

Please help me. Are you saying my mazda does not use an 02 sensor?

any idea where the TCM is?

What a terrible system Mazda has for replacing bulbs. Thank you for this video. By the way, be careful not to touch the bulb with your hands. The oil from your hands will make the bulb burn out prematurely.

I looking for autodoor lock censor at ceratain speed..mine is not working.

hello! I have the code p0327 when measuring voltage between the plug that comes from PCM it only gives me 1.3V

Where is the ignition distributor? could you give time stamp aswell please

I just changed the bulbs on my GFs mazda 2. This vid was helpful. Thanks for posting. I had no luck getting the plug off the back initially. What I ended up doing, was just pulling the rubber boot back enough to reach in, undo the spring clip and pull the entire connected plug/boot/bulb assembly out. Then I had plenty of leverage on the plug and disconnect.

Hello , does the same measurements apply to mazda 3 bk ? I HAVE A KNOCK SENSOR PROBLEM BUT ON MAZDA 3

Pozdrav Zvone.. Gdje da nadjem switch za rikverc svijetlo na mazda 2 2005 automatic? Hvala ti na odgovoru

Thank you. Did everything like you said except that i dont have a monitoring tool, and just a simple funnel, the problem is, that tha radiator fan didnt turn on even after the thermostat opened and only 4 liters of coolant went in... after the thermostat opened, had to turn off the engine cause the coolant started to spill out from the radiator. Now i am unsure that the bleeding went ok

are you sure thats the knock sensor connector? ive seen another vid where the guy says its the starter connector

Have you got any tips on replacing the Parker globes?

Nice video. Thank you🙏

Hello my car is burning oil and I run 10w40 could it be the pcv valve theres no smoke and it isnt burning it fast like every 1.5 Months i have to fill it back up

Thanks for the help. We were struggling to get the bulb clipped back in and the owner manual wasnt very clear. Its better to see someone do it!

Your videos about Mazda 2 fixes are amazing! Keep it up! I don’t have scan tool. Am I risking overheating the engine without one? Are they cheap online? Can I know without the scan tool that measures coolant temperature that the coolant is circulating in the radiator core?

Where is speed sensor?

Hi there, I have a mazda 2 and when the engine is running it has a constant ticking noise, you can not hear it in the car but when you lift the bonnet. Can you tell me if this is normal for mazda 2 cars please.

where is starter motor located?

Hi, im getting 4.66 v to my knock sensor and my resistance to the sensor is all over. Is 4.66 v okay as you said 5v

thanks

I just fought with my wife's Mazda...nightmare. But after like 15 minutes I figured that it's much easier to remove the 'connector' by pulling the whole rubber cover. This way you remove both: the rubber and connector.

Hi, how to acces the pcv valve? Is needed to remove the intake manifold? Thx

Hi, Where is the PCV valve?

10 minutes..thats all I could take