Видео

@@benshion8989 honestly not sure never used them

@@elidobbs5876 not sure what your asking. There isn't a specific 3s plug you just need to make sure your plug matches one of the plug types on the charger!

@@jdrcchanneltexas5497 I just bought brand new 3s batteries like the ones shown in video but the 10-1 charger doesn’t allow the plug to fit into the charging hole

Like they just butt up to each other. plastic ends only touch.doesn’t allow the female and male to connect.

@@coolspawngod it was the exo cage made by t bone racing but unfortunately they no longer make them.

Indeed on the stress

@@kraziezombie yeah unfortunately with the new lipo batteries they put out more power so they are a little more difficult to charge. Once you understand how they work and how to charge them it's a piece of cake. These types of RCs and batteries are not really for beginner's that don't have any experience with them. Some of my RCs do 100mph

Plug and forget it is when you're using basic NiMH where you can discharge it as much as you want or charge it to its full unbalanced cell capacity. With lipo batteries you're basically stacking phone batteries which is why it's slightly hurt more advanced to recharge it. Just like a phone. This is just like any 4 button charger and if you only have the same batteries you don't even need to change any settings. Just set it up once and leave it be.

@@austinprickett7443 no I had to remove one of the other connections with thick wiring that I wasn't going to use and solder on an ec5 connector myself.

@jdrcchanneltexas5497 okay thanks I was confused for a minute. I just ordered an EC3 TO EC5 adapter

You just need an adapter from your molex connector to the deans on the charger so would be I believe a male molex to female deans adapter. You might have to double check that though.

Thanks man!! ​@@jdrcchanneltexas5497

😂😂

Not very fast. It's more for off road dirt rock mud crawling.

I bought it, the steering motor is so weak that it can't work properly in off road. It is slipping centrifugal clutch type cheap steering motor that slips easily because this motor is not meant for this much heavy and big tyre type rock crawler.

Yes I know. I wanted mine differently then everyone else. I wasn't going for original style.

2S is 7.4 yes.

Mine did not come with an ec5 either I had to solder it on myself Also yes you always have to connect the 2345 or 6 pen connector as that monitors each cell in your LiPo battery it is for balance charging or charging in general so it can make sure that your cells are even

@@jdrcchanneltexas5497 👍

Yes it's normal for it to charge above 7.4 while charging. It will stop on its own when it's fully charged.

Yes it should be higher the battery is 7.4v but it has to use higher V to charge the battery faster. Mine typically runs between 7.5-8.0v while charging when it's done it should sit around 7.4v maybe a little higher or a little lower but should be by much. Same as when your alternator in your car in running to charge your battery it will run at around 14v but your car battery is only 12-12.5v it has to put out more cureent than the battery holds to charge it. You should be fine. Both Your cells should be right about 4.2 when charged so make sure your balance charging every time you charge so your cells match up or within 10 thousands of each other. Mine usually sit at 4190 and 4200mv on the lipo cells.

These are the 17mm

Before starting the charge you press the arrow up or down to change from 11.1 to 7.4 or whatever size your battery is

How it won’t let me

It’s on 3s

It’s the same exact one as yours

It only lets me change the volts on every other one besides balance chagre

Yes

good drift, locked front and rear?

@@jdrcchanneltexas5497 Front and rear?

It will beep and automatically stop and say END on the screen

@@jdrcchanneltexas5497 ok thank you

Are you referring to a liHv battery? If so I'm not sure as I don't run those. I'm not sure if there is 4.35v lipo battery's as I've always ran the standard lipo in all my rc's. You might have to look up the manual and see if it has the settings for that function. Sorry I couldn't help.

@@jdrcchanneltexas5497 I ended learning that you just need to put the charger on the LIHV mode instead of LIPO

Yes if you have set it to the correct battery amp and cell it will stop when it reaches that amp. So a 4s lipo that is 6000mah will be set to 6.0amp and will stop when it's fully charged.

Yes if your battery is 450mah.. .5 should be fine.

Cutoff is so the battery doesn't drain below it's threshold if it goes below 3.4v the lipo will be trash! The safety time should be how long the charger will run before it auto shuts off.

Those are ec5 connectors I soldered on so it would charge. You can buy an adapter so you don't have to do any modification. You could get a (female deans) to (male whatever you have) example.. If I have a battery with a ec5.. I would get a female deans to male ec5 adapter. So one end plugs into the deans on the charger and the other end plugs into your female plug on your battery type.

No those are for running it to your car battery to power the charger

@@jdrcchanneltexas5497 so they give u all those connectors but not a EC5 one

If your talking about a completely dead lipo battery most of the time you cant bring them back. They are trash at that point. Never let them get too low or they will be useless. You can somtimes set the charger to nimh and charge it for about 10 minutes to bring it back up high enough that the charger will recognize it's a lipo again and then you can start the lipo balance charge selection again. But be careful!! (I don't advise doing this if your not familiar with lipo batteries)

So when you charge your 2s lipo make sure 2S which should show 7.4v is selected then make sure you A is set to 5.2A which is 5200mah for every 1000mah it's equivalent to 1A.

Yes you can keep it at storage charge which is about 40% charged. Just be sure to check it every now and then while using it so that you don't drain it below it's charging threshold which I belive is 3.2v i never personally let mine get below 3.4 ever. They will last on the shelf not being used at storage charge for about 2 months before you need to re check the storage charge levels.

Super easy to do...press the + button until you see Nimh press play button. It will say charge on the screen. when you see the. A on the screen with a number in front flashing, press the + or - button again until you have that set to 5.0A that's your mah. Then press play again and then hold play button down to start charging. I will try to do a video and post it later today also. So keep an eye out for it!! Please follow me if you haven't so you'll see the video when I post it. Thanks!

Heres the video you requested hope it helps! ruclips.net/video/dT-vEMEFQF4/видео.html

Thanks! Hey girls can drive rc's too sometimes better than guys 😂😂

I don't use an adapter I cut off the xt60 and soldered an ec5 on!! But they do make adapters your just have to find one from deans or xt60 to ec5

@@jdrcchanneltexas5497 thank you!!