Видео

<3

My boiler pump is not working also

Hero! My problem exactly as you described as was the fix! Two minutes is all it took. Wife thinks I'm a hero. Thanks so much

Did all that and it’s still stuck!

Thank you so much, it may be a temporary fix but this has just saved us a very cold night. Worked a treat.

All ways leave your valves on the high number during the summer when not in use.

What a video! Thank you brother

Thanks for the remind how to do them

THanks I'll give it a go

Just wathced and very good info, just wonder how to adjust speed on this pump ? I have ecotech plus. Thanks

Fantastic video saved me a phone call. Really easy to follow and now I’m not sitting in an igloo. Thanks for putting these videos out.

If in doubt, give it a clout

Several great tips here thank you. If you're using a non-twist tightening connector, do you have to "tug" the pipe after you've inserted it, it is it the same process?

Thank you so much for this video! I’ve had no heating in my bedroom which causes my illnesses to worsen. The heating company can take over 4 hrs to answer calls & this has saved any long waits. Thanks again💛

Thx. This worked wonders. It was jammed and the fix took about 2 minutes

Thank you very much !!!!🙏

Some thoughts. I have a stuck valve problem, and although the pin comes out alright (by the action of its own spring) the plunger doesn't follow and remains in the closed position. I was thinking, with the water in the system cold to heat externally the valve, hoping that the difference in expansion would unstuck the plunger. By the way, my radiator is not equipped with an output ON -OFF valve, because in that case I could close that valve and open the vent, hoping that the difference in pressure could unstuck the plunger. Unfortunately, the advice to leave the valves open during the off season came too late in my case. Any other idea?

My pin is on the ‘up’ position yet the radiator still won’t heat up. Any suggestions?

Thank you i had that same problem with the Utica 150 boiler and i had that 110 error message and this video helped me fix my problem thank you again

You're such a life saver! Worked for me 💃🏿

Thank you 😊that’s amazing, fixed my valve , added some WD40 as well before I did this. Spent 2 hours thinking it was an airlock, turning radiators on and off. Never worked, was ready to drain the system, refill but tried this first. Thanks

This video is great! For anyone that gets to the end and your hot water still just will not flow into the radiator.... check the return valve is open too - that was my issue in the end 😅

If the pin is totally stuck and doesnt move when pressed, nor does it release when hitting the side of the valve - I've managed to release it on two occasions now by hitting the top of the pin with a hammer a bunch of times till it springs up!

screw is stuck, any tips on how to loosen screw?

this video came in handy, says a man with a stuck radiator valve 👍

Can the water stay tuned on ?

how to fix water leaking from this kind of valve? as soon as I open it, water starts coming out...so I am not sure....how to stop that water. or its just little water which will come out.

Thank you very much this helped me alot ❤🎉

Mine is stuck on. I'm in the blistering heat in a top floor flat. How do I stop it???

thank you. My bathroom tap is dripping just a little and I know it needs fixing. I'll be able to do it now having watched your video. 😊

Just about to call a plumber but thought I’d watch your vid first. Didn’t realise the pin was in a semi up position so didn’t think the video was relevant to my problem but pressed it down anyway with a flat knife & way-hay the whole thing popped up. Can’t thank you enough, you saved me the hassle and 💰

Bad advice, NEVER bang a pump or anything, do NOT remove👎 the VENTING screw while full of water, that's dangerous water damage PCB.

Did the job for me, thanks!

Nice clear tutorial. Sorted my stuck valve out in less than a minute. Thank you so much!

Thank you. Fixed my valves.

Thanks, boss.

Did this worked for me. Quick question. Some say used wd40 or similar yo help stop it worming. Good idea or mistake?

Was quoted £700 quid off British Gas as they said I need to flush the system, I decided to look on RUclips and seen this thankyou so much it took me10 minutes to do now my radiator is toasty warm

ALL NEW PUMPS LOOK HARDER TO CHECK , HOW DO I CHECK IF THE TURBINE FROZEN

Fantastic, brilliant fixed in 2 mins. Thank you so much ...I'm subscribed :-)

There is electronic device on the pump (wilo) i dont know how to remove it

Thank you! That worked a treat!

Hi. Amateur here. I fitted TRVs to all but the bypass in the bathroom. They used to jam all the time. So free them up like this guy did. Then, when they get hot, get a normal candle and place it on top of the pin, the wax will melt and runs down the pin and lubricates it. Not had one stick in 30 years and I think there are 15 of them. Do it once a year. One 10p candle lasts 30 years.

You sir, are a legend, simple 10 minute job saved us £££. Thank you so much.

it woked! thanks man

Adamsın broooo xd sorted after your video, appreciated 👊🏽

You want to make sure the pump is isolated before you take that screw out .

My plunger pin wasn’t stuck so what now?

Why is control stiff to turn when plunger appears free

Thank you, this saved me from taking a shower in a completely cold bathroom :)