Видео

I didn’t think they made them that small. Plus, I am just really cheap! Haha

Haha. Answer… it was in my left pocket😆

Thanks! Glad you enjoyed it!

@@PerrynBecky Thanks! Let me know how the project goes!

@@undaware that’s a great idea!

@@qconard thanks! It makes me happy every time I get to sit down and spin on it! Haha

I will take it. I am not a welder, so that is expected. 👍

Well thanks for watching the video anyways👍

Depends how the weld joint is set up. If welding will deform the plates down on the dynamic jaw, then it doesn’t matter if you can burn the paper away - it will still be essentially an interference fit.

But if you weld on the top side or reduce how much welding is done, the. If will probably work well👍

And a milling machine💸💰

Thanks I will go read that portion. I did try my welding helmet but that was way too dark. So I used sunglasses.

@@RossieLasdeso_ytshort thanks! It turned out great

@@mooseworks nice

Put the Crack pipe down. This thing is 100% badass!

@@goodasnewrepairs thanks! It was a fun little project.

Dissolve in hot water. Then drop in the hole with the tap. The part has to be aluminum though. 👍

من نمی فهمم

@@jeanvaljohn3921 that is what it’s for. Thanks!

I just measured. Looks like approximately 3.2 inches of travel. 👍

@@mooseworks okay thanks

In hindsight I definitely should have done that! I would like to add a hole pattern now, but those holes will need to be fixed👍 Great idea!

Thanks!

Thanks! It was a fun project 👍

@@AXNJXN1 I have looked at them in the past. I just never thought the cost was worth the single use case tool. However, the amount of wasted time may reason it after this project! Good suggestion! Do you have one? Are they good?

@@mooseworks Greetings! I do. I as WELL considered the SAME argument with myself... I decided to go the Harbor Freight route and this machine was absolutely, without a doubt worth $100.00. The time saved, combining working flat surfaces and the round stock you worked with your sander really, and I mean REALLY makes up for it in time based on the composite, fibrous rotary pads that come on them. It's a powerful tool and makes easy work! I actually clamp mine upside down to a table and run my round or square bar OVER it lengthwise and there's no other machine or process (angle grinder included) that's remotely faster. My Harbor Freight SCT has been outside in the Tucson Sun for 3 years and has yet to fail. It's a workhorse. For that reason, it's simplistic effort and effective cleaning time is certainly well worth it. The only thing is it's loud due to the gearing in it having such incredible torque. But that's nothing, just wear proper PPE, right? Love your build, but cleaning off the table top would literally take 1-2 minutes with an SCT. Best of luck and congratulations on your build!

@@AXNJXN1 this might be one of the single most valuable comments I have seen. I am seriously considering it now! Clamping to the table…. genius idea!!!! I am looking it up right now👍👍👍

I am 32 and I started welding at age 8. I grew up on a ranch and had the luxury of always having access to a welder. I have not gone thru welders myself - just had access to quite a few. Same with the regulator. I have seen some broken but mostly heard of the common issue 2nd hand. I am not a welder. I only weld as a hobby for project I need or fun. 👍

​@@mooseworks🧢

Send a email to the address in the video description and I will send them over for free! I hope they come in handy. Let me know if you end up building it and how it goes!

@@mooseworks I sent an email. Thanks very much.

@@bt5526 I will get to the email in a day or two. Not a problem!

I wanted the location to be symmetric to the other ones. I intend for this vise to last for years and wanted it to be right👍

I appreciate that! I will go read it and hit you up soon. Thanks!

Thanks a great idea! All I had at the time was a stick welder. So I don’t think I could only weld on the tap.

@@mooseworks Split a piece of copper pipe , drill a hole the size of the tap or a bit smaller and put it over the broken tap or bolt

@@davideden6413 that is freakin genius!

Not a bad plan, but where do I get liquid nitrogen?

Make a shallow cut on the bottom of the branch directly below the location you cut from the top.

@@mooseworks thank you

I do not have the tools to do a casting. Although that would be really cool!

Can you email the email address in the video description asking for the drawings? I will send them as .pdf drawings.

Thanks!

End mill on a drill press? Are you just suggesting vertical travel? If not, I would need a cross table and risk breaking the drill press!

Chambers on wrong side?

That’s what I thought! Haha

Thanks! I had never made a piece of jewelry like this before. I figured I should keep it simple!

Thanks! Hopefully mine lasts as long as yours. I appreciate you leaving this comment. Have a great day!

Seems to be the case. Mine is very stiff too!

Needs to be stiff otherwise it would move while running!!! Its spring loaded pulley would slow it down!!!

Hope they are helpful!

For sure! Just send an email to the one in the description.

@@mooseworkshi , can you send me it too?

@@НазарВолинець-ф6ш email me the request and I will send them over!

@@mooseworkshi , i sent an email

That he is! Thanks!

Yep. You are correct. I should have had my respirator on.

Thanks! It was a fun project and definitely different. Runout is one of the most important functions of a drill press and most cheap ones are not great. But they work nonetheless.

Thanks man! Maybe a DIY chipper?! Haha

Great tip! I do this with my chainsaw, not sure why I didn’t think to do it with this!

Thanks! It is pretty useful though! I am glad I got it.

You have no clue how much that means to me! I have really been trying produce videos that provide value but seem to be struggling... Thanks!

For sure man! It makes a world of difference. The welding table build took me a century to Finish. Square would have taken 1/8 the time!