Видео

Is there a reason for torx? I would just replace them with hex bolts

Carter , i have a oem rubber mat on top of my rear coil spings on my chevy trax. Do i have to remove it?

I've owned three Dana Design packs. One like this, a smaller pack and a bangtail pack. Superb, comfortable, durable.

hello Would anyone have the repair manual for this engine that could sell it to me? thank you

My mechanic showed me how the quick connect works to remove the from the top of the heater. the two lines that go through the body of the car.

I like ur videos. But dude, just like your dpf vid where you didint show how you took the 2 bracket bolts off I'm stuck and can't get to the bottom egr bolt bc you don't atleast say how you got it or what you used.

exactly what i was looking for. Thanks!!

What did you use to get those 2 other nuts off on that bracket so you could get the DPF out? Sat here for 2 hours trying to figure it out and couldn’t at all. Any info is appreciated thank you

By chance, do you know what size hose you used? I have a leak in the same area, and I'm assuming it's this.

2014 Chevy Cruze diesel no power from the turbo

Quick question that easy to do work

Is the process the same for the 2018 Equinox diesel? I've found a kit in Canada but not sure how legit it is.

Such a bullshit with diesel emissions.

Did you run into any alignment issues? I did this on a 2015 Volt. Wondering if I should have done 20mm instead of 30mm, the sway bar seems to be making contact (or nearly) with the control arms.

I removed the inlet hose (13251460) and when I did, I broke off the clamp that goes into the engine side. It is a Norma-RSS NW 16-15, but I cannot find it anywhere. The inlet hose comes with the connector to the firewall side, but does not come with the clamp that goes to the engine side. Do you have a part number for this connector or a source? I've been searching for the connector for Holden engines (Australia) and the Vauxhall engines (Europe), but have not been successful. Thanks in advance.

What do you do with the sensor that hooked to the EGR tube? Just leave it?

How to drain the gas on a 2017 Chevy Cruz

Where can I get the kit?

I really appreciate this video. Do you know the name and/or part number for the inlet tube that connects to the trottle body? When I removed the clip (the same way you show in this video), a piece of the plastic tube broke off and stuck to the clip. Now I have a boost leak because the tube will not completely seal against the trottle body face. Thanks in advance.

How does the ECU handle this though? My cruze limits top speed if the pump isn't working.

That is just cheating... it's obvious that the piece was stuck on with soot and you just skipped tnat part... it's the whole reason i'm looking up these videos!

For everyone asking about where to get it, etc. start looking for canadian companies

How did you get that bracket out of there?

Only for off road use,,lol

Ive got a 2015 Diesel Cruze that will crank over forever but doesnt even attempt to start. Other than the possible fuse box positive being loose, the turbo having issues, or this EGR valve being stuck.... What other things should I look at? Multiple good batteries were tried.

Is the car on a diet or still heavy up front? Mines stock trying to figure a way out to get rid of my clogged muffler. Stock ecu also

I know this video is four years old now, but everyone should know that the torx bits to remove the EGR valve are, indeed, T-30. There's another video on RUclips showing the same thing, but the guy says they're T-27. DO. NOT. USE. A. T-27. BIT If you do, there's a good chance you'll strip the torx, and you'll be in a world of hurt if you do. Ask me how I know. 😂😂😭

Hi Carter, do email to PM you direct please?

So your vehicle is limited to 64mph now?

Hi I brought the same lift kit and I tried 225 60 17 but it did not work its touching the struts . any advice can you suggest me .is it going work if I use a spacer . will you please replay . thank you

How do you know what all the sensors are? got a reference material?

Came across your video for i want to do the same on my car to remove the annoying sensors. How often do you clean the pipes to prevent the soot buildup?

Where is the egr value on chevy cruise gas engine

How many miles are on your Cruze? And how many did it have when you did the delete??

You Sir rock ! Thank you.

What size hose would best fit to drain it?

ATS505 carbon cleaner cleans out the carbon without having to remove EGR

Good shyt my man

That doesn't sound good lol

i have a 2014 diesel cruze - removing these are easy enough but what (if any) needs to be done to the computer? to avoid def countdown, and speed countdowns? mine keeps going into countdown permanent fault codes and want to get rid of that junk...

AMIGO LA EGR NO SE LAVA CON EL CONECTOR ASIA AVAJO, YA QUE EL SOLVENTE CAE O SE METE AL INTERIOR ASIA EL SENSOR Y LO DAÑAS , LA EGR SE LAVA CON EL CONECTOR ASIA ASIA ARRIBA PARA QUE EL LÍQUIDO CAIGA ,NO SE META !

Steps look great! Real vision and bringing it to life. Nice red lantern

I just did the delete and do you think it’s okay to leave on the muffler after I deleted the car I just I don’t want it to be to loud

so when are you re-doing the basement stairs? 😛

Why did you chose this insted of the aluminum lift kit online, how is the ride?

I just replaced my turbo charger I have 172,000 miles on the vehicle. Also my coolant lines this is the second time the first time I put a coolant hose on the fittings and the second time the fittings all cracked at one time at the same time so I ordered from Amazon, you coolant fittings and line and put a rubber hose on them

Hey, I got a 2014 Chevy Cruz diesel and I would like to do the same. Where did you get the lift from? And do you have like a video after like for photo shots of the vehicle. How was your drive? How is the shift points and all that with that left her and bigger tires?

How do you remove the EGR? It's very tough, it won't budge.

You failed to show how you routed out the space for the logs. Your video glossed over some things and spent too much time on others. Maybe that's why 1600 people saw it but only 28 gave it a thumbs up. I wanted to love it, but sent this message instead. Learn from this and improve! You have the skill :)

what size tires did you end up using on the car front and back?