Видео

"entry-level professional" there's no such thing ...

What range will the new glasses have?

I hate when they say case. And there isn't one!!!

Please would you make a video showing uart connection and setup in betaflight or inav. Great product, I have GM1 but not sure for to connect it to flight controller board. I would like to control the pitch angle with a rotary switch on my transmitter. I have TX4 and RX4 free.

Great edit!

Exactly what I was looking for to put on my nitro slash just have to figure out how to mount it inside the car instead of outside because any flip with a fast vehicle an say good by to that camera an gimbal

So you did headtracking on Goggles L before goggle X? Thats dumb af....you guys dont know what your doing anymore....

How to reduce jello and Flicker?

Why so many Flicker hahahaha

could you share the settings you use on the gofilm20 to film this?

Goodjob CaddxFPV. Im also enjoy my #GoFilm20. It's awesome cinematic quad.

This video shows a cable (3.5mm) coming from the Goggles L, attached to the controller? Is that what is needed to have head tracking? Or is head tracking gyro through goggles to gimbal.

can work with Caddx Walksnail Avatar GT VTX Kit fully?

is it possible to record without vtx?

❤

Calling your self a colorist by adding a shit filter is wild

How do I install the newest Gimbal Firmware (there was no upgrade cable) in the GM3 included ? Is there somewhere a guide or manual ?

Where is the promised head-tracking for the Googles X??

Why will it not work on my goggles X

So the total height would be 8.3mm + 10.5mm = 18.8mm?

I got mine all up & running but cannot get it to turn with the goggles, moonlight & goggles L both updated. it does work moving the model but wont turn with head movements - all movements are backwards -any idea? in PTZ mode, tried the 3 following modes & sensitivity 0-5-10. have not tried going negative in those settings. Cable is plugged into the white dot port below sd card. powered by 3s shared power with vtx, has a fan. video feed is fine, im new to this hobby just purchased it all for my fixed wing. said standby mode at the bottom i turned that off but still no joy.

I’ve updated the goggles, updated the moonlight kit, got the plugs in as shown, tilts as should when vtx unit is moved but won’t move from goggles even on ptz. Done the calibration too but still nothing. I can see a blue light flashing inside it. So close but don’t know what to do now. Tried everything.

🔥 can't wait to get my fpv gear again CaDDx for the win 💪

how come you have such nice shots from moonlight in the dark

Hello caddx team 👋 I have one simple question.... When is the new module for the Google x coming out? Should i buy google x now or wait for the improvement? Wait or buy now. Something coming ?

Moonlight Vtx doesn't pair with fatshark dominator latest firmware. The signal gets too low, and a red box flashes and disconnects. Plz fix this.

Second and while the transition effect could probably do to be tinkered with to make it a bit less "off" - It's got fairly smooth, "slow wave" sort of shapes but the transition happens quick like a flash. Imo it should either be smooth or sharp, not a compromise between the two - the actual colouring work and the piloting are both pretty cool and I like the stylised golden hour vibes and the actual flying looks good for the fairly relaxed vibe I think you're probably going for with the whole thing Not a professional at any of the above, this is just a layman's opinion. Do what you enjoy and looks good to your eye. Tastes are subjective, they just often overlap

First and that looks so edited it’s bad

Hello, I just bought this model of camera and it is getting extremely hot. It gets up to 90 degrees when it's on the table and shuts down. Does your camera get hot? How can I cool the camera?

Can the gimbal be setup for head tracking with the Skyzone 04x pro goggles as I have the google mount Walksnail Vrx?

Good news, DJI & Caddx :)

Love Mr Steel style landing on a car tyre trick. Caddx stuff is great and well priced. (I only wish the box goggles had diopters available. )

I have 6 DJI drones, DJI FPV Drone, Avata 2, Mini 3 Pro, Mini 4 Pro, AIR 2S, & AIR 3. All Fly More Combos. I have 3 sets of DJI goggles. Goggles V2, Goggles Integra Motion 2 Combo, & Goggles 3. Even though I don't know how to fly Acro yet, Im wanting to get into traditional FPV Drones. I have a Eachine Novice 4 rtf FPV package, & a Whoopfly16 rtf FPV package to learn on. The Novice 4 drone, came with a Radiomaster TX12 transmitter, & the Eachine EV800DM goggles. From what I have heard the Walksnail air units are a lot cheaper & smaller than DJI AIR Units. Im thinking about buying these goggles, or should I stay with DJI only.

When will goggles X board to support head tracking be available?

Very nice gimbal! Are there plans to make a DJI O3 compatible version? My money is ready.

This is only half of what you need. Do they have a camera and transmitter to go with it? And if so why not sell it in a package 🤷🏻‍♂️

My goggles L show as being "delivered" but never were....

The goggles L come with a built-in head tracker?

How dif you guys get the information on the view of the fpv? Referring to the altitude, attitude and voltage?

Can it used with goggle x?

Where can I purchase JUST THE SCREEN?

This is sooo sick 😍🔥🔥🔥

What about head-tracker support for goggle x?

The black-and-white effect in the video is designed for artistic purposes. The DVR and footage captured by Goggles L are in color and high definition.

So no av out ? No av in ? No hdmi out? Or external antenna elongators..or built in recievers ? Etc.so what on earth is the big deal with these

will other vtx work with headtracking or will it be moonlight only?