Видео

very interesting !

short the C11 and remove from that place and you will have more current and that C11 put in the top of the schematic

high voltage electric candle 😂

Come back. We need you.

Hi, is there a way to connect two transducers to one point, and code it? Im having issues with the coding portion.

I am soooooo jealous of your corona discharge,,,its so hard getting the right volumetric discharge without sparking

You can use this discharge to produce nitric oxide then use that to make nitric acid. It works very well. Use a glass tube around it with foil as the feedback capacitor and pump dry air through it. Have the gasses collect cooled and bubbled through distilled water. Collect the gas left over and cycle it through a condensor and cold trap dryer. ❤

We shall send each other some volts now😅 haha

very clear. thank you!

so the corona discharge only happens at the positive terminal. that is good to know. as with my field propulsion experiment I can use negative high voltage to prevent corona discharge. correct?

art

I see you like to test different corona discharges. So I can suggest you an experiment: a magnetohydrodynamic drive that propels an aircraft, that’s a corona discharge which interacts with magnetic field. So the concept is as following. Install two corona emitter electrodes in front and on the back of your craft; supply the electrodes with co-linear field coils (or permanent magnets) in order to stretch two coronas as far as possible in the opposite directions so this way you’ll have wider semi rings of air current sideways. On the left and right sides of the craft you should have electromagnetic coils or permanent magnets to push down both semi rings of air current; if the front electrode is positive and back is negative then the left side must be a north magnetic pole whereas the right side is south magnetic pole. According to Flemings’s left hand rule the air will be propelled downwards thus pushing the craft up. This concept seems more advantageous than so called “ionocraft” because the latter consumes a lion share of its potential payload with a big array of corona electrodes whereas the concept that I just offered uses vast air flux cross section without need to stretch any grand electrode arrays; it basically makes a “virtual ventilator” of much bigger size than the craft itself. I have subscribed to your channel. It would be great pleasure to see my idea tested. Thanks in advance.

The saw looked a bit like miniature stage lights :)

The saw is soo awesome!

2 Forces Pushed JLQY Pulled jrQñ 2 mosfet can be on at the same time Paralel now zvs zeries returded...

The "K2" in the Paschen curves is not potassium ("in gaseous form"), it might be a badly printed "H2," i.e. hydrogen (or maybe misread and misspelled by the type setter, as there is some similarity in shape between a a capital H and a K?). The "A" (or maybe it's a Cyrillic "D"?) might be Helium??? Or maybe Ar?

All this high voltage ⚡️ what are you going to do with it 🤔

Fascinating. Great job!

Can i pot a crt flyback tranformer in wax? Im using a zvs driver circuit to drive it and i see a lot of corona discharges around the core and the secondary part of the transformer. Will potting it in wax help?

Bada-da-dada-da-da Flare Corona!

nice

Balancing payloads on jabbed fools. They can bc they are not he or she and people don’t have rights only men and women do. They just ran along to be queer. We are electric so this was very easy. It’s the after shock that takes them also all Those earth quakes have an natural cause

That’s the name Of the program where you can hack the idiot’s. Down To their bank accounts, if they are asleep or awake dream stage and on and on it’s sick

Awesome! Thanks for the tutorial! I'm working on a voltage multiplier myself. I'm still trying to make a 400kohm resistor in series for it so that i don't damage the diodes. Is there any way to make a high voltage resistor?

Как будто русский акцент. Не?

You could reach much higher voltages with less current using large metal speres instead of pointy needles

Can we connect multiple transducers on the same outputs? Like I want to make the same project but with multiple transducers directing towards one point and all. Please help

my multiplayers and transformer died on 38 cm spark gap =(

The exploding wires like this can be used to directly detonate some kinds of explosives. These are called exploding bridgewire detonators and were used in early nuclear weapons.

What circuit did you use for this? Is it a simple high voltage generator with and without a spark gap or is it something else?

Здорово!

Really appreciate this information.

That was excellent

Wow it seems like thees sparks are extremly loud

Roman 😎🤙

Me habria encantado hacer algo como esto,lastimosamente no me queda mucho tiempo pero almenos puedo disfrutar de estos videos gracias!!

Great info thanks

st. elmos fire

Great

Surprisingly I’m not from styropyro, but I do love watching his videos

Great job! What is that HV transformer, where did you get it? and What is that capasitors?

Здравствуйте , подскажите пожалуйста, как вы думаете, течёт ли в триоде ионный анодный ток даже тогда , когда лампа заперта сеткой, отрицательным напряжением? В лампах серий гми, гу и т. п.

Excellent video! Thx!

I saw a lot of people covering their hv multipliers in wax, yea, this is definitely a good way, but I covered my hv multiplier in silicone under vacuum, silicone is also pretty soft and multiplier also could be easily repaired.

I love this explaination about the Mazilli ZVS driver, by far the best I've seen on RUclips so far about this circuit, thanks!

If I put one of these inside that one office door that shocks everybody with static, will it turn the knob into some kind of russian roulette death knob?

Thomson's ring discharge was a demonstration in my intro E&M course! Neat stuff.

What types of diodes are you using?

Jeez... that thing looks like an electron beam irradiator.... 😳

5x 70Mohm + 50kOhm + 5,7kOhm + 10kOhm ???