Видео

Hey Tom I have an 81 interstate. I have the same red wire on the accessory terminal. It’s spliced off the smaller red wire from the ignition switch.i do not have the green wire like yours. What’s the story with these wires , cause I’ve seen other interstates without them. I also have the cycle sound radio

Thank you . The video will be very helpful

Mine was full of gelatin but luckily the piston was still moving. I just cleaned out the reservoir and flushed the lines but now my front brakes are dragging and have destroyed one of my rotors. Guess it's time to pull it all apart and fix it right. Thanks for the video.

This was only a 170 cca battery?

Tom do you know if you can replace the lines inside the tank.

Thank you so much for this video, this is exactly what I needed.

Fantastic job congratulations thanks mate for your support goldwing, I have been trying my for last 2 years but no time and England not easy for parts 😢

Thanks for your videos, you make it all look so easy and your explanations are great. I’m starting the carburetor rebuild on my ‘76 Goldwing today, Howdy from South Texas!

Thank You!

Hi thanks so much for your video. I got a 81 gl 1100 about a year ago and just rebuilt the carbs watching your video it helped me so much. The bike was sitting for a long time before I got it after I put the carbs back on it fired right up but after about 5 minutes it started to smoke anyway I think it is my valve stem seals but it could be the rings I'm no mechanic just watching RUclips video's the one thing I'm confused about is when I put my camera scope into one of the cylinders there was a lot of gas pooling on top of the piston and the intake valve when I had checked it the next day. I don't know who to ask about this situation just thought you may have an idea. Hope you are still doing well.

Thank you so much, man. I have been watching a lot of your videos. I am 100% new to motorcycles and it is helping so much because I have the exact same bike so I really appreciate all these videos.

Where did you find the gas sending unit? Is there anyway you can give us a link to purchase it?

Hi Tom. I wanted to followup on the issue I mentioned below. I solved it. One of the compression springs on the opposite bank of the #3 carb was in incorrectly and prevented it from closing. A quick change and it was fixed so I did the pre-synch and all's good. I really appreciate this series that you did and probably would have put the carbs back on the bike and not found the issue until I went to start it up. Your pre-synch step got me to look at everything and catch the issue beforehand!! Much appreciated.... Good riding.....

Hi Tom. I watched quite a few videos before tackling this on my '97 Valkyrie 1500C, yours were the best for me. I re-did the carbs because I was always having trouble syncing all the carbs with Carb 3. I have a digital carb sync device. Your pre-synchronize test with the light showed me that the butterfly valve was not closed (bottomed out) on carb 3. I can't understand why it would even be open but it is, a lot. I obviously have to fix it although I would have put it back on the bike had you not shown me that test, so thanks for that. My question is how do I get the master carb (3) to close so I can adjust everything to it? I am guessing it has something to do with the bolt on the side of that carburetor. Any help/suggestions would be appreciated.

great vid

I thought I was in over my head but this video saved my GL1100 project bike. Thank you

Your content is amazing, so thankful for your videos

If i have any issuewith video it would to not use brown scratch pad. That is very rough. Maybe green but for sure follow up using blue to really polish cylinder. Other wise great video

i gotta find that can of schmutz 😂

why do repair guys always play music , I cant hear what hes saying

The strps of the rubber pieces at 8:20 is what i need tobsee in detail

Doing my GL1000 carbs tomorrow. Have only ever replaced throttle cables, so this is very interesting. Thanks for the excellent video.

where do you buy the oem fuel sender unit? can’t find it anywhere

Where did you buy your rebuild kits at

Thank you!!!!!!!!!!!!!

Do I need to replace bearings?

Very clear instructions

Great videos

Thanks for this...I was able to use the concepts here to unfreeze the piston in my master cylinder on my 2003 GW. It's as good as new.

Guess you gave up

I saw no mention of the feeler gauge adjustment?

Thanks great video

I will be removing mine today great video.

詳細又清晰的拍攝

I am a new owner of a 1985 GoldWing. Boy oh boy, is it gonna need some work. You, my friend are 'Heaven' sent. Thank-you so very much for these videos. I watched the carburetor rebuild. Tricky. I might pull it off after watching that incredible video.

Very good video. It's going help me alot very soon when i have to rebuild the pump on my H180. It started to leak a little last season. Thanks for the video.

needle jet? mine didnt have one!!

I was just gifted an 86 aspencade, this is by far the most helpful video on the matter, and made me realize that if I have to pull the tank, I might as well have a tire on hand especially since the bikes been sitting about 12 years

Very informative, thank you for your video. Although I don't think the music is necessary! It actually takes away from the video..

Amigo ocupo pistones y anillos para un motor 1100 1985 y el juego de empaques algún lugar en donde pueda comprar? Que sea seguro por supuesto gracias y saludos...

Wait… you didn’t put the second seal in (the dust seal)? Leave them out altogether?

Great video. Simple to do. Great tips, also. I would not use a metal peak, I use hard plastic one from Amazon.

I own a 2020 Goldwing DCT Tour. Simply to say, incredible machine. I do almost everything in my garage I am still not sure about doing clearance adjustment. Never done that. I got a quote for 700.00 by my dealer. I might just let them do it. I don't do heavy miles per year and so, don't think its worth it for me.

What year gl is that from. Mine is a 1975 and doesn’t have the accelerator pump on the bowls. It has it on top.

Your watch says 5:55

I'm trying to rebuild my master cylinder for my 84 aspencade 1200. for some reason the plug wont come out of the cylinder. I've removed the c-clamp but nothings happening. Any ideas??

Excellent video. I need to replace the fuel line from the fuel pump to the carb assembly. It looks like the same hose you left connected. Is it possible to remove that hose without removing the carbs?

Hello, didn't the coating block your two filters? I like to do the same, but not sure about the filters. Thanks!

do you put a syn gauge on after you installed them or does that get you good enough?

Great video Tom definitely helping me form a plan of attack here