Видео

Thank you feeling confident i can do this myself now ! Subscribed.

A while ago so you might not know or remember, but did you use a switch with red LED backlights? There only seems to be ones with white LEDs or it doesn't say at the moment

Thank you. I need to tint one next Monday

Thank you for this clear explanation . Blessings🕯️

Nice informative video I like the clap of the leak off line instead of individually putting the stopper on . Much better .....was your engine up to temp before you carried out the leak off test ? or was it from cold start . thank you

So, I have a mid 2014 Highline(14.5 model -some updates) and I didnt have to take my door trim off. Took 10mins to release the trim that holds switch in, disconnect the window switch and the heated mirror switch and swap the window switch and put back in car.

Fantastic video as always. I really enjoy this channel 😎👌 Thank you!

Is there a torque setting for the Rocker cover bolts.

Good to see a well explained, no fluff guide by someone who knows what they are doing, Thank You!

My car bounces only once and then comes back to its original position. I have seen some cars that are very firm and I can't even push them down. What does that mean? Does it have to be very stiff and difficult to push?

Hi did you bought autoauth standard for unlock secure gateway? How did you do step by step for autoauth? Thank you, I bought autoauth standard but it’s not work for my car

I encountered a problem, the start-stop gives me an error. I mention that I bought a new battery, I put it in the car's memory and it still does the same. What do I have to do to make my start stop work? If you find video clips in this sense, please help, thank you

so glad i found this video, ive just done this earlier today as i started having issues getting into 1st and the inside gear knob holes were way off. ive adjusted it, there was a lot of slack on the left sided one which went with adjustment. took it for a little drive and it did seem better. ill go for a longer drive later when im not busy and check it properly. it started happening when the car was warm so thats the next thing to try later. Thanks again for the video.

What size are the core plugs

Great video..👍 No need to be torqued then...?

Super informative, really helped me figure out the basics of my machine! Appreciate it👍

Great video mate! Just one question, should I replace the valve cover gasket after changing the plugs? Or can I keep the existing one?

Victor reinz, the worst. Instead you should use febi, because is made of nbr. Better than Victor. Cheers mate

Great video. This definitely help me. Thanks

Just watch it backward for step by step guide

One thing about the jack under that reinforced pinch weld is that that pinch weld will tend to bend when there's a flat jack under it. If you place a hard rubber hockey puck on the jack pad it will keep that pinch weld from bending. They also sell metal lift pads with a slot in them on Amazon to prevent the bending.

One of the clearist, concise and waffle free 'how to' videos on this subject. Keep up the good work.

Do you have a video from the start 🤣 But thank you so much! I’ve heard VW interior is the same for Audi A1’s heat resistor, would you be able to confirm this?

How did you remove the old switches?

Great video 👍, exactly what i need to do now to stop the water. Did you have to do a coolant drain first?

Amazing video thanks.

Hi, any ideas why the handbrake lever won't release properly on the iload van please

5v from ecu PWM signal

How do you know what voltage Noid bulb to us as wrong voltage can blow the noid bulb?

Hi, positioning lamps stay always on when headlight bulbs are on?

Good job. Tnks

Thanks!

i have an issue with the 1st gear only, it gets stuck or blocked by something on the way in, i have to comeback to neutral and go back in, or try to go hard on the left first before pushing forward

what was the problem here ?

What year vw polo was this?

no help here

Great video mate! More power to your channel. By the way where do you get the pinout diagram of your ecu? Thanks appreciated

Lifesaver, got new bulbs a few days ago fitted at Halfords…upside down. Thankfully this video helped me fix the issue in a few minutes.

Complimenti, io avrei preferito vedere lo smontaggio, ma il video è molto bello. Se avessi indicato Dacia Duster Techroad avresti avuto molte altre visualizzazioni, è il modello più difficile da smontare e trovare video tutorial, perché su gli altri modelli sono più semplici smontare le candele. Bravissimo

Thank you, this was really helpful.

My bolt by the hub is extremely rusted and won’t move. What’s the best way to go about this?

This is a must also if you are replacing the discs

Hello mate. I need that door handle pulley replaced on my car. Mines has all cracked. Are you in london ? I have the part, I’ll pay you to do it for me please. Thanks

Great video 👍🏻 Does this apply on xenon projector headlights? The cutoff on projector headlights needs to start on the 2% or 0%?

Hi, what autel is that?

Thanks for making the video. Can i just ask if its ok to reuse the old bolt? I've read that it should be replaced, as its a stretch bolt. However all the video tutorials show the old bolt being reused. Thanks,

Top notch video

Thank you so much for sharing! Clear explanation and great demonstration. One Tip which helps with position of the measuring device. Open the bonnet and use for example the bonnet reststops to align the position (or any other left / right mutual bolts). You have the open the bonnet anyway. This will make it easier to ensure the measuring device is pointing straight at the headlight. Measuring the height of the bulb is an estimate but it can be improved by using a small laser light and leveler which points at the bulb. Then measure the height between floor and the laser light.

Thank you,brilliant and educative

OhhhhhhhhK 😂