Видео

It have a 25hp kohler, carb 24053 Runs on choke, choke off dies. Power up runs on partial choke. Open it sputtering. Clutch out-no throttle dies. Jet or solenoid?

They look great. Im looking for 2 sets. Maybe 4

He do house calls

Have a happy Holiday Season, Ray 🙂

Dissamble and big cleanup worked.

Min runs good on high bud turns off on the low what do I think

Can i get stl file?

This looks like an amazing solution -- awesome work. Any way I could grab the file?

Metric

i always did my own oil changes for 60 years. then as the years passed the hardest part was getting under the car. then out course when got under it you for got your wrench or rag or something . but i did enjoy doing it myself. saved a little money in the process.

Goled sacid

😅 i thought it was to go through top to bottom , here i was fighting with needle trying to unplug and then I watch this video 😂

You couldn't afford one more orange lens cover? It sticks out

I had a almost new chair and a nice scooter with a bad motor I put the motors off of the chair onto the back of the scooter and to say the least it works very well

This was a great video,

Bought a new inner tube for a pitbike that was a moped one and had to strech it so much i put a hole in it, put it in the back of the shed iv xome across a moped im working on now need the inner tube ill be trying this. Thanks

Hi could i ask what size those pads are please

Thank you for your video, you 100%right don’t take your car to the dealer, they will damage your car, I think they got trained by the owner, who ever they are

Have this exact grill and both wheels have been broken for years. My brother has a 3D printer, but didnt see your STL (could be too dated). This great grills wonderful but would be nice for it to roll again. Can you kindly provide the STL again? Thanks, great video.

🎉🎉🎉 I've stripped that jet screw 🎊🎊🎊🎊😂 im gonna delet the whole solenoid hope it will wirk

Where is part 2?????

You know if the guy fixing a product doesn't know the name, mispronounces it and doesn't know the model number, I just stop watching and move on. This seems like the most basic of knowledge about said product. Jeez!!

Even though you said exactly what I KNOW but your tid,bit of information was duely noted👍

Question on change engine oil every 5k miles. Do you replace filter sametime, too, or on alternate oil change?

this is awesome going to try it on mine. they are very stiff, but i dont want to buy the thin flimsy aftermarket hinges.

Please tell me you can mass produce these

Dude Cash in hand. Your sitting on a cash cow

Did you check the rotation of the tire? Some are indicated on the side by the company. If so, i think you did it the wrong way! If you see no inscription, you are OK.

Thanks for the tip

Would it have come apart easier if you re inflated it

Your video saves me a heap of time, thanks a lot!

Can I get a updated 3D STL?

I have an older original Pride Go Go Elite Traveler. Has been durable, only had to have the brake unit replaced many years ago. Some parts are becoming discontinued from online sources. Some used parts are available from Ebay. I am leery of buying "off brand" mobility scooters. Pride, Buzz Around and Drive brands have been around for some time and have generally good reputations and user support. I would not recommend buying any mobility scooter that needs repair, unless you have mechanical and electrical skills and ability to source parts and information. Professional scooter repair, if available in your area, is not cheap. Batteries are like car batteries, but are sealed. They go dead when not kept properly charged, when run down to dead, when stored in a hot car or garage during the summer, when left on charge continuously. When properly cared for batteries have 2-4 years of useful service. It is not rocket science to open a battery box up and change out the batteries, unsticking the old batteries from velcro requires some strength. You'll need a long phillips screwdriver and some common hand tools. Make sure that the measurements of new batteries in the online ads are exactly the same as the old ones you are replacing before you order them. Smaller scooter replacement batteries, like 12 -22 amp hour, cost from $60 to $120 per pair from Amazon, Home Depot and Walmart.( Two 12 volt SLA batteries are connected in series for 24 volts)

Shop techs are somehow convinced that an oil filter needs 1000 lbs of torque. Just to be sure. I just hand tighten. I don't have Popeye arms, but never, ever hand an oil filter leak or come off.

Yes, always drain the crankcase before removing the oil filter. Much less dripping.

Cool. Thanks! Like others, I was out of ideas. I cleaned off the solenoid plunger, but didn't realize the brass part and the jet were under there.

Easy to replace the battery, but when I picked it up to put it back together, the insides - all the little pieces and mat fell apart. After 2 hours with tweezers, strong light etc, I still don't have it back together. Taking it to the dealer and they better not try to charge me labor to fix something so cheaply made.

Excellent video good illustration.

4 wheel scooters are more stable but have larger turning radius.

Legend is 3 wheel. I have one.

What brand post hole diggers are those ?

Hi Ray, I don't think you would still have the old board lying around because my board seems to have three surface mount capacitors burnt. I cannot tell what the values are if any on the board. My question is can you take a close up picture of the soldered side of the board? If you don't have the old board, maybe you can take apart the good one, and take a picture of it. Thank You in advance if you can. PAUL

lmao @1:19 i saw that coming been there done that many times

I got a new one

What year honda? Also. With super thin oil the new oil filter has to be filled with oil before it is installed!

Comment faire l'équilibrage de roue de scooter électrique pour personnes handicapées car je dois faire faire le mien car mes pneus s'usent trop vite pourriez vous me dire comment faire merci

How to get a tyre off mobility scooter that hasn't got a spit rim.

I found the gas line to be too long and now kinks. I will be reusing the old stopper with new gas line threw it. The airfilter i had to trim to fit also.

I ha e a question for you. Have pretty much the same engine on a lincoln ranger 8 welder. I was cleaning the carburetor and dropped the float needle in the bottom half of the carburetor which goes into the block. How can I get it out?

Awesome! If you don't mind sharing the file I would love one to print out on my 3d printer.