Видео

My connection at the top came off How to I find and reconnect that cable

That Audi hit 75mph wickedly fast. What do you think the 1/4 mile time might be? Sounds very smooth while cranking out the power. Did you have to tune the tranny to match the power level?

I just have one code popping up it Torque restriction due to clutch temperature any idea?

Any way to add the drive select mode to the dis?? I read a thread where you go to the gateway (19) then long coding bit 8 but my OBD 11 does not list a bit eight

Will this work on a 2015 s3?

Hi! I have an AUDI S4 2009 in which I replaced the clutch plates and renovated the mechatronics. The phenomenon is that when you put it in D or R from a stationary position, the gearbox hits hard, but only when the oil warms up. I adapted the clutch, but only drove 1-2 kilometers with the car. is it possible that I should drive the car 100-200 kilometers to learn it? thanks!

You did this with one hand.. I'm hoping I can do this with two. Thank you my friend 😊

hearing good things about this tune but would also love to know what exhaust is on that s6 with the red paddle shifters....sounds damn good.

mod list?

Does anyone know if this same procedure will work with my 2014 Bentley Continental? Will it do any harm if I try?

You just saved me time thanks so much

Link to Install VCDS in my pc please?

Are the exhaust flanges available for sale?

This legit?

Hello! Im troubleshooting my friends tuned C63 that cuts all power on full throttle, it sets one code Quantity control valve bank 2 - Short circuit to positive. This is the control valve on one of the hp pump. Have you ever heard of this? He is running Spool performance pumps.

I only have a dyno channel, anyway to add?

What is the adaptation in the newer VCDS ? it does't use "48" like the old days.

how you get the code canu help me please

If one bearing was bad, the other bearing has just as much run time on it. You were already in there you should’ve replaced it. I know the reason you didn’t was because you did not have the spine tool for the clutch pulley. I think you should’ve just at the end of the day bought that tool and then you would’ve had a complete rebuild, including installing a new copper slip ring. . Thanks for the video.

Faaaak yes🥂

Audis suck

Whats the numbers

Hello, it is very important to do “Main valve pressure calibration” ? Thank you 🙏

Thats pretty omg thats sweet bro

Why don't you show which buttons exactly need to be pressed. I have not seen a less useful video than this one.

Would the same apply to a 2016 A7? The part I'm finding 8K0905217C doesn't say it's for an A7 or A6. Did you have a different part number?

Is this with the engine on or off?foot on brake or not?

Hi, i dont have options in Basic settings like you do, i tried it when temperature was 80celsious, is that maybe reason?

note every 50000 miles ( i do mine at 25000 miles ) replace the tappet/ follower below the hp pump,, and lube the face with engine assb. lube..its easy to do, takes abot 15 mins... this wil keep the cam lobe below the hp pump from wearing

Yes it should.

Nice work, not to be expressed in stages 😅

Hi ;) Maybe you know how to reset all green menu settings. I pressed something unconsciously? :)

Does this work on 2016 Audi A6?

You saved me 🙂

Hi there Thanks for post8ng the video, I would just like to ask if you do all the setting with the engine running and brake pedal pressed down? Regards, Milan

This settings is correct in S3 8v ?

Fixed mine but not able to get the plastic parts to snap back together. But fix does work

Raptor is a Ford. I won't degrade my TRD ORP. Not necessary IMO.

Hi,help please,a6 c7 7gear dsg.change gears good.when start driving it is little harsh in drive or reverse is the same.i have vcds,what can i do?

Anyone know is this works on s4 B8.5?

when trying to add to my Q5 it just backs up? Is there a special tool or door to open seems like I always needed to use the audi / vw bottle.

Does it work on skoda?? Amundsen?

So whats the adaption procedure?

Will this for for obd11 ?, I need to get the 5 digit security code in order to code things in my 2012 A6 ...

While doing the adaptation for clutches the bar does not rise at all and says aborted for safety reasons . Same with main clutch . Does this mean clutch packs are shot . Or possibly the Megatron repair kit with new solenoids do the trick?

Goes out with an Audi a7 built in 2019 new model?

really helped me out man good video👍🏻

Still good with using the light fuse? No check engine lights? You made it look so simple, I like the fact you can turn it on with the headlights. I can’t find another video where they used that particular fuse. Thank you

Hi, I have replaced the mechatronic unit on my car and performed basic settings however there are sometimes issues with engaging gears 2-3. Do i need to run one of the other options e.g IDE 12710-Initialization of clutch friction coefficient model after mechatronics exchange?

How can I put the driving types or “drive selection” on the speedometer?