Видео

Thanks for these videos. The details are wonderful; “end screws are different and look like this “ and these insights help hobby mechanics like me working on my 85 FJ60 “Wilson.”

How did you handle the radiator. I was told that you have to clearance for that somehow?

Where in South Africa can I restore my FJ 62 Landcruiser to this level?😢

Great video. There are 4 bolt holes to secure cover to engine, maybe 2 fl that connect ton air box, and a couple that are a couple of open holes in the valve cover nothing attaching to them, why is this?

Please Please a video to show how you will merge the FJ55 wiring herness to FJ62 Wiring Herness.

Nice work, could you make another video to show how you will merge the FJ55 wiring herness to FJ62 Wiring Herness.

Nice work!

Thats an achievement man well done!

Im digging it!

The video you took is fantastic! We have some car related items. Do you accept sponsored products?

I love it! Those Iron pigs are awesome, but i did get a kick out of calling the 3fe "modern."😂 You wouldn't happen to have a fj80 service manual I could buy?

these are awesome jeeps....and they are getting more and more desirable along with their flat fender cousins (willys mb, cj2a cj3a, cj3b)...hang on to it if you can

to remove the entire engine harness from a 2f in a 85 lc does the entire da sh have to be removed?

FFS stop calling it a TRUCK. It’s just a LANDCRUISER just call it that.

❤❤❤❤❤🎉🎉🎉🎉

Need some soap

Thanks for sharing the build. Question for you, where did you end up setting the base timing? I have a 1F in my 40 that when purchased came with an Offenhauser 4BBL intake, edelbrock carb, header and flow master installed. It idled good and sounded ok crushing but would make your eyes water it was so rich and completely gutless. I found the timing was way off from spec, like several degrees ATDC. I set it to spec, 7 BTDC and it helped enough I could start tuning the carb. Ended up at 12 BTDC and it’s good. Good power and runs smooth. Had to disable the secondary on the carb though. Just bought a Holley 2bbl to try out. I tuned a friend’s 2F that has a Rochester 2Jet on it. Ran ok but was a little rough at idle and had a flat spot. Ended up setting it to 14 BTDC and it purrs at idle and going down the road. Flat spots eliminated. If you’re still at 7BTDC, you can squeeze out some more performance with a timing change.

Lovin it Jonas! Had a few questions for you. When I drained my fuel tank the other week, I noticed dirt in the bottom of the clean drain pan from the gas. It wasn't atone but about a quarter of the pan had dirt/grime in it.. How big of a deal is this? Will the fuel filter catch dirt accumulation like this? Truck sat for a while. Probably at lease 3-5 years at one point. Cracked Rocker support. When I was installing the rocker assembly with a fellow cruiserhead one of my rocker supports got a crack in it. It toruqed down just fine, but wondierng if you've ran into this before. Thanks, Dan

Great job as always!

Love you videos... I always learn a thing or two about this old rigs

This made me happy. You may need to swap in a master cylinder from an 80 series inorder to get the most out of the brakes. Fj Cruiser steelies will fit but you will need 1.25" spacers for the rear. I like that EFI better than the Sniper, it looks like a GM throttle body.

This's sniper efi kit?

So cool

Awesome work Joans!

Exciting man

Don't leave me hanging on this. I NEED to see it finished. Great job to this point.

Nice!

استمر اخوك من السعوديه

Question, what did you use to connect the SBC to the Toyota transmission?

Great episode!

Another heart ❤️ transplant…Wishing you great success!!!!

I love that you used a small block 5.7 they are great engines. I know everyone uses the LS now days but I’m old school great work man!

Really good content🎉

What size lift and tires on that rig?

What did you do to it that makes it sound like that is it the cam

Can you make a video of taking off the door on a fj60

Great video, but if I were the customer watching this, I'd wonder why there wasn't a soft towel or something under the grill when laying face down on a rusty tailgate while working on it.

Rare to see a jeep towing a cruiser, Land NOT PT cruiser that is

Amazing. Just amazzazing

I wonder how hard it would be to do the 2fe in my 60, obviously I'd need a 62 tank and computer and all that, but injection would be nice, love the video's man keep em coming

Is that crowbar?!! Aw man!! The journey continues :)

Going to run my 3FE until it dies then resurrect ole “Grace” with an LS. 5 speed coming for sure!

2FE! I have being thinking about this engine so much. I have a nice running 2F so no hurries but one day if I get to find a good top end 3FE I learned a lot from your videos! thanks

This has a lot of great info for pulling a motor.

Need a 12ht in it

Youre awsome dude, the first five seconds and i already learned like 3 things about my 3fe

I still need those parts brotha

Great work and content man, love the enthusiasm. I hope to one day need to look back on this video for reference. Cheers!

That por15 paint is going to kill the frames on those

Great video. Very informative and intertaining. That music at the end was a bit annoying because I couldn't hear the motor. Otherwise, I liked the content.