Видео

Will they cut stainless zip ties?

❤😊😊😊❤

I think it did extremely well. Plus Hurcules comes with a 5 year warranty that you can do same day in any HF in the country. I'm sold.

Your first test trying to isolate the pressure gauge only is prone to fail and "leak" - you need a larger volume for a decay test. Everything leaks, plastic hose leaks, every connection leaks it can be very small but still leaks.

I recently tried to change spark plugs on my cx9 2017. Couple of things i learned and want to share my experience with you. 1. You might be able to change 1st and 2nd plugs, but 3rd and 4th coil are the hardest part to put back. I tried for several hours and ended up cross threading the coil bolt. I would highly suggest please get it done by Mazda professionals. 2. The mechanic disconnected the hose in order to put the coil. 3. My car was at 98k kms and spark plugs looked pretty good. If I knew it i wouldnt have changed them cuz they look pretty good. 4. I would prefer Mazda OEM spark plugs over NGK. 5. Spark plugs are changed once in a while, i found it convenient to get it done by mazda professionals. Just few learnings. I have always changed spark plugs of my older cars but Mazda cx9 spark plugs are not easy to change.

I try with fine sand it works too. Just put sand into the hose until no space left and then bend it while heat it then dip the hose to bucket of water while rinse the sand out

Can I get a link to the hard line an fittings

The real question is, can you get an adapter to use Milwaukee batteries on it? 🤙

Do you think it could handle walk in coolers/freezers?

Looking good

I've got the twin grip and pistol grips❤ S/O is just too high😂

This is great! I wonder what happens when the trans or steering fluids run through them. How hot do those get? Do they get hot enough to relax the hose and kink?

You missed their version of snap on LN47acf talon grip needle nose pliers. I was so excited when I saw them, but I had to have them now so i had to buy the snap ons. Fortunately i got them for 50 bucks

Good review, how about a look at new generation hose clamp that eliminates the issues with Worm Gear and Spring clamps. Check out Safety Spring Clamp. ruclips.net/video/G-lRQESr59s/видео.html

Problem solved. Thank you from the philippines

What about the Hercules brushless Nibbler? How would it compare?

This video is just nit picking. The tools work and have a great warranty. They tried to bring manufacturing back to the US which was nice. It didn't work out for them, but the sets they made are fine. I find some rusty sockets here and there from Taiwan, China, and even Germany produced tools. Just wipe off any loose rust and coat with oil or silicone as you would for any tool you accidentally leave outside over night. I bought both of the US sets and so far they haven't shown any signs of rust. Hopefully, they'll try again in the US, but maybe this time focus on some specialty tools that don't have as much of a saturated market as ratchets and sockets.

If you don’t want to spring for cordless pro model, use an Amazon battery power pack with 110v outlet. Pretty cheap on prime day

I've been designing a "plate" for the holes in the strut tower you mention around 11:07. As of right now the plate allows me to mount a MAP sensor, boost controller, Radium catchcan, and ChaseBays fuel filter. I did this to avoid drilling holes in my freshly painted engine bay. I'm sure I could modify it to fit anything you might want to put there. LMK if you're interested.

Well done 👍

GET TO THE POINT. This is a "how to bend hoses" video, not a how to dismantle parts of a vehicle no one owns video. No one cares about the process preceeding or following bending the hoses.

Thanks for dropping nuggets along the way for those of us who don't "know" or overlook the details . Brushed not brushless, for exclusively straight cuts, etc. Extremely well done review! I'm looking forward to picking up my own now.

You can put a copper line through the hose and bend it to the shape you want, heat it to about 250-300F and keep it there for about 5 minutes then throw it in the freezer for an hour, pull the copper tube out and you're done. Only 90 degree bends are a pain as you will have a real fight to get the hose off the copper tube, for that I drill a few holes into a piece of sheet metal, enter some bolts through the holes and place the hose in between the bolts so it would stay in place as its being heated.

I have one, its nice to mess around with but its slow compared to my 7cfm pump. Since most units have a service outlet it doesn't really make sense for me to use it. Probably sell it and move to the Milwaukee m18 vacuum if i decide to go cordless.

profit 1st people 2nd safety 3rd

I just bought one, excited to use it. Thanks for the Video! Install looks nice!

I got this pump this week. Its nice and compact, but it substantially slower than my beastly JB 7CFM.

How about larger diameters? My current issue is a 1-1/2" fuel fill hose that I can't find OE or even similar. All I have is straight to start with, one end with maybe about 40deg and the other about 15deg - bigger spring, I guess...

Steam starts at 212 degrees at sea level, but it can be much hotter under pressure. If your not looking for a reason to buy the nifty steam cleaner, you could just place the hose into pot of boiling water while it is restrained in the position you want. Leave it boil for a few minutes and then cut the heat and cold dip it or if you have time, leave it in the hot water until cooled to ambient temp.

Just a question for you. Is it required to have computer module reset after spark plug replacement?

what temp do you heat them up to ? Thank you very much for the info I'll try doing my oil return on my R33 gtr

Thanks for the upload, learned a lot today about these fittings. Going to come in handy re. fuel lines for a Porsche 944 and Range Rover Classic that I have these projects lined up for

Yeah I cant get this 3/4" coolant hose to stay bent using this method.

Totally fine for automotive, I would think, particularly through a blue hose.

Pulling through your manifold is going to slow your vacuum process down. I like to connect with vacuum hoses directly to the unit. Also that is a 2CFM pump, I think it did a damn good job. I would like to see a micron gauge directly hooked to the vacuum pump by itself and see if the pump can really achieve the 23 microns it's rated for. Also has a low oil capacity, so for clean new installs, it might work, but if your pulling on dirty line-sets and compressors, to me looks like a no go. Also no gas ballast. I looks like a great tool for automotive though and I am sure that is the intention for this unit. That's might though.

This thing is quiet as hell when your pumping it out also just did a 2and half ton today almost got perfect vacuum

Pulling a vacuum thru a manifold and long 5ft hoses thats not vacuum rated takes forever no matter what size pump u use. Also that pump is 2 stage deep vacuum also. I love mine it comes in handy AC service tech has the best practice for pulling vacuum without restrictions. That guy is a genius

11m for a 2cfm pump is great😅

I bought this pump for automotive use. Replaced my ac compressor and it was awesome to not have to rely on a power cord. Later on today once the sun goes down I'm going to replace a solenoid on my wifes cars ac compressor. This is probably my favorite Hercules tool as this Texas heat is no joke. The fluid extractor is a great idea. I need to look into that to do oil changes and transmission fluid changes on my vehicles.

hey man how are these holding up?

I'd hate to be the sucker who helped you buy this! Wait a minute....

As far as a fluid extractor I can assure that a hand pumped extractor is LEAGUES faster that a compressed air powered one. And better priced.

For pulling a vacuum I recommend Dow Corning high vacuum grease over nylog. hands down does a much better job.

Start of the pulldown was really slow.

I'll have to change out the vacuum tree when I pick one up. That 3/8" port is useless as is for me.

I don't know any technicians that pull anything down with a quarter inch hose except for maybe a recovery tank. At least from what I've seen in the field 3/8" is the standard minimum for a vacuum hose nowadays.

I'm sure if you used 3/8 or 1/2in evacuation hoses instead of pulling through your manifold, it would pull a lot faster than this.

I picked one of these up as well. So far I haven’t been able to try it on a residential unit but did pull a vacuum on my truck after replacing the evaporator. I think it’s gonna come in handy as long as I’m not expecting it to compete with my bigger pump.

No gas ballast?? This is awesome regardless

Quick question. I was about to pull a trigger on this one but is it A2L rated? I been looking online of any info but cant find one. If you have any info, pls share. Good videos and reviews by the way. Thanks