- Видео 16
- Просмотров 210 553
Fixit Dan
Добавлен 25 июл 2014
Love a quick fixit project!
Ride on Mower Deck Repair (Quick n Easy)
Don't throw away your mower because of a bad cutting deck, Repair it.
Просмотров: 550
Видео
Volvo XC60 Front Brake Pad Change (Easy)
Просмотров 3019 часов назад
Quick video on showing how easy it is to replace your worn brakes on a Volvo XC60 Other Volvo's will be a similar process
Semi Truck Brake Lining Replacement How to Rivet
Просмотров 77Месяц назад
How to replace brake linings on a heavy truck, lorry, semi etc
Mercruiser V8 Remove Motor Fix Oil Leak
Просмотров 18910 месяцев назад
Could not remove rear mount bolt to pull engine oil to fix oil leak!
RB20/25 No Start Skyline R30 Drift Car Build
Просмотров 299Год назад
Getting this old Skyline R30 running after sitting for years
CRF150r Big Wheel Conversion & Test Ride
Просмотров 17 тыс.2 года назад
Turning a small wheel to big wheel, installing swingarm bearings, test ride
YZ250F Steahly Flywheel Weight for Trails Test & Review
Просмотров 1,5 тыс.2 года назад
Modifying Yamaha YZ250F to give it some low down torque for wheelies & trails
Mower Engine Easy Half Rebuild
Просмотров 383 года назад
Pulled the whole engine apart to fix no compression problem, easy job
Honda XR250 Fixed Not Selecting Gears, Engine reassemble Part 2
Просмотров 7353 года назад
This is my first time pulling a bike engine so far apart and back together again to attempt a start up!
Honda XR250Not Selecting all Gears, Engine Strip Down Part 1
Просмотров 1,4 тыс.3 года назад
Found the problem of xr250 only getting 3 gears
Fix V8 Mercruiser Stalling & Big Flat Spot Easy
Просмотров 91 тыс.3 года назад
This should be the same fix for any boat with a dirty carburettor V8, V6, 4cyl different but same. Bayliner 5.0L V8 Capri has a huge flat spot and stalling when taking off, this fixed the problem and runs great again. Happy Boating!
How to Fix Bent Dull Dirt Bike Plastics
Просмотров 5 тыс.4 года назад
There's heaps of vids on this stuff, so here is the dodgy way I do it..
Extending Trailer Hitch
Просмотров 1,1 тыс.6 лет назад
Fixing and modifying old school ski boat trailer to suit a Bayliner Capri. I would have made it in one long piece had I known it was already bent and sleeved but it works well.
Land Rover Discovery 3 how I fixed hand brake & gearbox fault in the outback
Просмотров 11 тыс.6 лет назад
Right in the middle of Australia when a fault message comes up! "UPDATE" It happened again a year later, this time I tried reverse gear first thanks to Ima-Good-Guy who suggested in the comments and it worked first time.
Fix V8 Mercruiser with no spark easy
Просмотров 48 тыс.6 лет назад
Fix V8 Mercruiser with no spark easy
I believe it's time for a new deck.
Never🤣!
Well you did a great job of fixing it up to mow again 😮, it should last a long time if kept clean 😊😊😊 I hate to throw stuff away that I can fix
Thanks, yes I love a challenge to fix something others would throw away!
I still have about 35/40 Murray and 100plus craftsman mowers I was planning on fixing but I’m just getting to old 😢😢😢
I’d like to take a walk through your yard, are you in Australia?
Wow are you in Australia? I’d like to take a walk through your treasure yard!
Do you have a speech impediment? What language are you speaking?
Australian broken slang English
Hey if you want to sell me that Fender I'll buy it off you just the way it is right now let me know all right bye I looked on eBay and Amazon and they want too much money for them
Thanks you man you saved me a ton.. I had a boat mechanic try to rip me off to ... This why I never trust mechanic
Glad to hear it worked for you 👍 help me out with a hit of the subscribe button thanks mate.
totally thought you'd sheared the bolt off in that rear engine mount 🤣 Did you get it back in okay
Yeah the struggle was real getting that out😩 went together reasonably easy, couldn’t get rubbers in a hurry so ended up getting a second hand bell housing with good rubbers & new bolts.
nice vid man :)
On partzilla all these parts are $938 shipped brand new OEM for my 2024 crf125 check them out they got it all!
please where is the black wire really go to? I can not find one with twoo wires!
The black wire goes on any earth or bolt on the motor, I put mine on the coil bracket bolt
@@fixitdan5248 thanks for quick reply…. I just ordered one on Quicksilver as you did . This Monday it will come so I can install for mine…. Thanks again!
I have this same mercruiser and having trouble with the water pump. Can you link the pump you used on the install? Awesome video by the way!
Thanks, it’s was the genuine mercruiser one for that engine number, that’s why it was strange I had to modify it
wow. im so feed up with videos that cant just simply stay on point and with people who cant hold the camera still enough to not give people motion sickness from watching.! thx
Hahaha yeah mate, was my first video, they get better. Subscribe and watch the rest too you’ll see👍
Same thing happened to me but in the water
nice one i had the same issue at hand at the moment so what is the part number for the ignition sensor and wheel assembly please.?
Hi, they were the updated mercruiser replacement parts for my engine serial number, the update is sealed better & has 3 wires as I showed , not sure of the part numbers but it’s the standard thunderbolt ignition module & sensor wheel. If you have the older points style I’m not sure what’s involved, maybe the whole distributor is different. If yours already has thunderbolt ignition then just order the sensor, wheel, rotor & cap to suit the engine serial number, pretty sure if it’s thunderbolt there is only one to suit the V8. Hope that helps
99 Dodge pickup what color are the fuel pump
Hey man! How can i find the right fit for yz250f 2018? It seems pretty hard online to find it
That’s a tricky one man! I looked on the Steahly site & have ones for 2017 & 2019 they miss 2018 so I’d say the 18 model either runs the same engine as one of those years & will work. You should be able to find some info from Yamaha or online.. Hope that helps. Don’t forget to help me out & subscribe thanks mate 👍
Hi I’m in a marina in Uk a friend has this engine, please help. How / where do you re-fill the fresh water coolent once the hoses are reconnected. Thx in advance this would be very helpful
Hi mate, if the hose setup looks the same as this one then it’s raw water cooled, it sucks water in just above the propeller. Hope that helps.. don’t forget to subscribe thanks
How could you tell the water pump was bad I could here you in the video
When I checked it over before starting I could feel a little movement in the shaft just moving it by hand up & down, then when it was running I could hear a new grinding squeal noise from it.
I have a crf80 would it be the same??
I’m not sure about the 80, someone in the comments might be able to help with some info.
If the CRF80 is like the XR80, XR100/CRF100 stuff should bolt on to the CRF80.
did you need to change out the rear shock?
No mate, just screwed the spring nut a bit tighter to suit weight of rider.
Geeesus don’t give a shit about boat just show ignition
This is the same thing going on with my boat
I used a heat gun on my stuff 6 years ago
Nice! There a handy tool to have hey! I learned to shape plastics on car bumpers in the nineties, saved a lot of money on repairs 👍
Unfortunately you don’t show how you got it all out or in and you don’t show where the wires hooked up to helpful somewhat but not enough
It’s very simple, the 2 wires go exactly where the original 2 wires go and the 3rd black earth wire goes anywhere on the engine block, I chose the bolt that holds the coil bracket as a good spot. The unit screws inside the distributor with 2 screws in the exact same spot as the original, there is no adjustment, just screw in place. Hope that helps, I should do a detailed vid on it but it’s stored away for winter at the moment.
Thank you Thank you.. liked and subscribed
Hello !! I would like to change the crf 250 wheels with the small 150 ones...it's too tall for me. Does it fit?
Get a set of supermoto small rims or can lower suspension with lowering link
Awesome!!!
I think u had a weak fuel pump also
12:02 is your gasket off?
Good pick up, but no the gasket had an extra hole, they must make the one gasket for several pumps maybe.
well done mate!!
I have a 23ft 225 sundowner with a Omc 5.8 it runs perfect but won’t go past 3,000rpm spec is 4600,4800 full throttle anyone have any ideas?
Hi, haven’t worked on that engine but if it’s old school & not fuel injection, I’d start with the fuel system, check fuel filter, fuel quality, pull carburetor and clean all jets. Then electrics , spark plugs, coil, distributor leads etc. Depending on carby , the secondaries maybe blocked only giving half throttle, if it’s electric injection could be some limp mode etc
@@fixitdan5248 thanks man I’ll definitely start with fuel
@@oddlyrightoddlyright2475hey! Did you find the problem? Mines doing the same thing .please let me know.
@@georgeforall my tach is off top speed is 40-45mph for my boat and it’s hitting the mark
@@oddlyrightoddlyright2475 ok . Thanks!
THANKS GREAT VIDEO
I’m gonna do this for my bike. What size swing arm should I get
I went the 150rb (big wheel) swing arm but some are saying the original swing arm just fits the big wheel but better in my opinion to get an original big wheel one👍
Would of been a great idea to grease and inspect the suspension linkage, they look rough and in need of some TLC
Thanks Jermaine Clement
No volume.
Boat like this ektricik Bayliner 32ckw. 30 Mike rabfe telsa cl 34.8 mole apps vater 38 kw 36 me BMW pater 41ckw 39 mile range
I want to turn my Rb into a R can you sell me your old parts ?
I put it back to an R & sold it already, kids are on 250’s now
I might be interested in rb parts if you are selling.
@@andrewbray2266 Sold it all mate, my boys are on 250’s now
Meant the other guy. Don't know how to tag him.
@@fixitdan5248 that’s lit im 5’6 and 117 pound I don’t want to ride a 250 until I’m a master at wheelies
Hello friend, you do not know if the crf 150R enters an oscillating arm of the crf 250
Hi, I don’t believe they will fit without some major modifications, better to have the original cut & extended . I have read of people putting 18/21 wheels on them but in my opinion better to get a 250
How much money in total did this cost
Was around $1050 with secondhand swingarm , wheels & new chain. Got my money back when I sold it, my son just went to a 250 so I put the bike back to a small wheel & sold it then sold big wheel kit for $1100. Happy Days 👍
I've got a problem where if I pump the throttle all the way forward, a small amount of fuel will squirt into the intake, enough to start the engine, but then it only runs for a few seconds. Fuel pump?
Could be fuel pump mate, be a matter of elimination. I’d start by disconnecting the line & put it into a bottle and see if it pumps fuel with nice flow, if that’s all working then time to pull the carburetor apart, might just be a stuck needle & seat.. let me know how you go.
@@fixitdan5248 actually it ended up being the exact problem you dealt with in your video, you saved me big time thanks a million!
@@pcough100 Awesome, glad it worked out. Don’t forget to subscribe 👍
Just did!
looking to convert mine for next racing season could you give me a list of everything you put on it
Well worth it mate, all I changed was the swing arm, wheels , rear 56 sprocket & chain to suit an rb. I hunted around the bike wreckers till I found 150rb used parts. They say to beef up the suspension but that just depends on your weight, my sons light so I didn’t need to.
@@fixitdan5248 my buddy said he got rb wheels and they fit on his 150r without having to change the rear swing arm. did you try that by any chance? i wanna know if that will work so i can do it to mine
@@evanduck6542 I didn’t try unfortunately, they probably just fit adjusted right back but you’ll have no chain tightening capabilities.
should have had a bigger swing arm
It is longer, that’s a genuine rb (big wheel) swing arm, there’s not much difference maybe an inch or less.
@@fixitdan5248do you think you’d be able to move the axle back so the small wheel swingarm fits? Heard that might work so will try that out for mine
@@chloemx7534 Maybe, would be tight, best to borrow a big wheel & try it on
dude the “longer” swing arm is only 3/4 of an inch longer. me personally and many others on the internet have swapped their small wheel 150R with big wheels without even changing the swing arm at all. because in reality 3/4 isn’t making that big of a difference. you can theoretically get that difference out of the chain adjustment.
Where do the long black ground wire go
I think I put it on the bolt holding the coil bracket at back of motor
my boat bogged out on me this weekend would idle and run great then got to a sand bar hung out for a while when shifting into gear and giving it throttle it would bog out. took gas cap off and it took off like a scalded dog
Interesting, must have a blocked breather. Where I live the wasps in summer will make mud nests in any little hole they can find, my chainsaw wouldn’t start & sure enough the exhaust was blocked with wasp nests.
you should edit the sound of this video, great video terrible audio
Yes thanks, I’m slowly getting better at editing. You should see my first video, you’ll get sea sick watching it..
You just saved me over $4,000. Thats the estimate I received from the boat mechanic. My boat is now running better than ever. Thank you
Good work mate for having a go at it yourself, helping each other out with a bit on knowledge is what it’s all about.
your belt seams abit lose? :)
Yes, all tight now thanks👍
keeps it from stalling at low rpms?
Yes definitely improves slow riding with low revs & reduces the pinging, add some lower geared sprockets as well & feels like an endurance bike.
Plz tell
Where I got them guy mean?