Видео

When you put those 2 coats on the plywood at the beginning do you also coat the scarf cut or do you leave it raw?

You lost me with the drain plug tube with the bolt washers and nut. What is that process for. I have used a lot of 5200 and you did a nice cleanup on it. Love the series. I missed my calling. Your jigs and techniques are impressive.

Is the epoxy that you are using UV friendly?

where is the part 5 of building center console . nice video. .keep it up

Please wear a dust mask when sanding or cutting! It’s no fun but being able to breath! Read a labels and believe it when it tells you not to inhale vapors! You can research COPD and see how to protect your lungs! Be safe and good luck!

"Make some dust..." That describes most of my woodworking attempts.😅

Not sure of the need for the ribs after you've shaped the boat on a jig. A closed /capped gunnel would hold the top side shape? Good looking boat

You skipped a HUDGE HUDGE part right after you cut the plywood ! That joint is sooooo critical ! You just skipped right over it to where you were finished it and started gluing it. Now it's pointless to even watch the rest of the first video. I would have absolutely subbed and watched every one of these videos but I can't get my head around how stupid it was to skip such a critical part at the start of the construction.....

This boat can take on some very very rough seas; providing it has a good captain and good bilge pump.

Where did you get the glove box and tackle storage boxes? Everything I’m finding is ridiculously expensive

Nice, any plans for that sir? And what is the make and HP you installed?

That's an awesome boat , great job

Beautiful boat.

When you first fit the chine I noticed you didn’t put glue, and I thought I would have put glue. I wonder why he didn’t put glue, and I thought about it and realized that gluing the chine to the side would make it VERY stiff and would probably crack or put stress into the material when the side of the boat was bent to the frames. And then you mentioned that you had a notion about the difficulty with bending the work. To me it’s pretty obvious that you are correct, and I came to the same conclusion before you mentioned it in the video ! Really nice attention to detail , fine work. Being a Newfoundlander power dories are the pickup trucks of the water, I’ve often thought about having a nice large one for up here on the mainland. They are becoming more popular today here in Eastern Ontario. I would much rather have once of these than a fibreglass one. I use a large aluminum boat, with wood interior for convenience. I would much prefer one of your boats, if I didn’t have to trailer much. Beautiful boat.

Retirement project for me. Thank you.

Beautiful boat, that guy's singing is awful.

Looks like a classic Midland. Nicely done, sir. ⭐️⭐️⭐️⭐️⭐️

Ton vidéo né pas complet why

"I rolled it out" Do you mean coated it with epoxy?? Good idea though.

Does watching the printer, and watching him sweep sawdust, really help the viewer. Good content spoiled by boring content. Smh. I'll watch it all though.

Impressive

I learned a lot about what you can do and what you shouldn't do, what tools you need and so on. Great job.

Have you gone into what type of plywood u use? is marine grade essential or can exterior be used? How much is marine grade now? thanks

Is access ever needed under the floor? im strongly considering making a boat like this.

How about a nice piece of stainless running down the bow for impact and to tie the two sides together? ya or na

What happened to the boat? thats a good impact.

How do you feel the flat bottom rides compared to a v-hull ?

Is there a possibility of being able to make a flats boat out of this. Aka a flat deck on top of the funnels or would it be too tall out of the water

there is no way a clerk could build this😄

I wouldn't have thought that you could bend the sides with the chines pre-attached. How thick are the plywood sides?

Quint says “ Master Skiff Builder!”

This is the second boat I've seen where you are using the PVC decking. Have you been happy with how that material has worked ? I too have purchased your plans

Very nice build, sir. Love the lines of your boats. Thank you for sharing your builds with us.

Boa noite meu amigo, que legal admiro muito barco artesanal Deus abençoe seu trabalho❤

Love your videos, I could watch you build a boat all day.

Purchased my plans to build this boat at worldboatskiff.etsy.com

Why do the sides lean out so much or at all?

Hi! I would like to build a boat like this, to be more exact something like this. I'm interested about the thikness of the plywood. Can you please tell me? It would be a very big help. I checked the link in the description, but I don't really find it.

How long does it take for the slow hardener to cure ???

Where are you from ??? And is this boat building just a hobby for you ? And if you have a 40 hr a week job what do you do ???

Is that track or guide for your power saw something you made or bought, and what do you call it ???

nice workshop... my dad was a drummer!

Just saw one of my favorite ❤ albums on your wall Rush Moving Pictures!

Watching all your vids and you are giving me inspiration to order the plans and begin building mine to use here in the Chesapeake Bay.

love the videos and the way you explain what you are doing, I see you using the premixed epoxy thixo rather than mixing epoxy glue, is it just quicker and easier, and is it as strong in your opinion. I am from Ireland and love the content, keep up the the good work. I hope to take on a boat build myself.

Nice boat

If you think this is a good boat for you to build, take a look my plans here worldboatskiff.etsy.com

What a beautiful well built boat and it's a rocket

Do you use the same epoxy for all your applications, glueing, coating and fiber glassing?

Good to see you back and making progress on this skiff build. Looks good. Hard to believe this skiff is only 17+ feet. Looks much larger. Thank you for sharing this build with us. Have a great week ahead.