Видео

Do you need a socket extension to reach the drain plug?

How did you get the rack and pinion back up? Because I’m working on my car and lowered the rack n pinion to get more room to take off a hose. but all that done now I’m stuck at how to put rack n pinion back up so it can be bolted under the battery.

Hi. After liberation with silicone oil. My treadmill creates same problem... Is it due to motor belt oiling or less oiling umder belt .. i feel jerks when load applied to treadmill... What to do

Appreciate that Roy! Getting ready to do ours for the first time as soon as my gaskets and oil come in.

Brilliant work thanks

How do u get the valve off the bracket

Thank you. Quite useful.

I love this guy , you save my machine and my money

Mine wasn't there but mine is a 2009-2011 aveo sedan. It was close though and also under the intake. I just followed the pipe from the hard line to the solenoid.

I appreciate your review but at 200k miles I have some questions, about some stuff that will affect HP and how effective that tune is. have you had the engine compression tested? Have you checked how well your injectors are working, have you had a de carbon service? I get what you are saying about a better driver but if a better driver in a stock car can be faster then a better driver in a car with a tune will be even faster then the stock. Unless you can't keep the tires from spinning when comparing two of the same exact cars the one with more power because of a tune will always be faster.

my pulley seems to be out of alignment with the flywheel, so the belt falls off when spinning. I can't seem to slide it in either direction. Any thoughts?

I didn't end up seeing another video from you about how the gfb diverter performed.. better or worse?

If you disconnect this sensor you will not know when you engine overheats

Don’t forget that there’s gaskets for those plugs too.

Thanks for the video... helped us determine it was ignition switch! Cheers

Fill from the top where the plug you took out, fill where the plug came out.

I took all 6 bolts out, but not sure how the "flathead" screwdriver part works. Wish the video was longer and contained that part. I suspect the bracket on the bottom has to be removed, which means one more bolt. Either that or the exhaust manifold, which your video shows you didn't remove, so I'm thinking bracket is easiest. Was about to do it an hour ago, but it started raining.

Super common on 1.4T, waste gate bushing wears out, gate doesn’t close all the way. Throws a underboost code.

Needs turbo

Waste gate is cracked Once you remove turbo you’ll see it I’m assuming low boost DTC?

The flapper on the inside of the turbo needs to be adjusted.

The wastegate valve port on the inside usually crack. Would recommened pulling the trubo and checking it.

wastegate issue maybe?

Needs a turbo

I was thinking wastegate and wastegate flapper issue not closing shut completely I where I'd start

Fuel filter without regulator can make problems on this engines?

What are the symptoms of a bad left side outer tie rod end

You got a video on the cvt fluid change ?

Thanks bro thats odd my tranny fluid stick is right on top

Dude, you are funny! I was crackin up at some of your comments. 😂

Great video, is there any tips for getting the manifold back on, am having an absolute nightmare trying to realign the remaining studs on the cylinder head to the manifold.

Źle części ,zła diagnoza

Ty so much

Is there a Haynes manual for getting the rack & pinion out? I have a 96 A4 that I need to replace the rack & pinion on.

So pissed bc I tried doing this and the socket worked for the alternator bolts but not for the power steering pump, and the socket I used was JUST half an inch too long to use a proper ratchet on. AND it refused to lineup with the power steering up. Super fed up with this job.

Great review of this product. No bullshit

Same as s4 from 2006?

What size fixings were used?

Cool info . I’ll do mine tomorrow….

Very cool thanks Roy

Was it an EVO electronic assist?

Great idea....my Sportstech F10 has the same problem....it seems loads of Treadmills do the same plastic pully on a metal bar...designed to fail. And you buy a new front roller or Treadmill!! Not this time!! 😃👍👏👏👏

thanks for the video same car explosion happen with my car later all the antifreeze started leaking

Video debe hacerlo de día o tener buena iluminación para que se vea algo y no oscuro

Finally, somebody that really knows what has been going on with my treadmill !! I have a Sportcraft TX 400 (bought from Walmart 7-2003) treadmill!!! ❤️ I've been trying to figure this out for YEARS!!!! Thank you so much for your video!!

Mine is almost 40,000 miles and my engine is super clean it gets dusty wipe it with a microfiber cloth.

I put a circuit tester with voltage display to the white wire and tried to start it. It lit up and gave me a reading of 8.3v . Is that saying my starter is bad

This is definitely going to be my problem. I am missing my skid plate. Thank you so much for making this video. I looked up the part on Rock Auto and assumed it went on the transfer case. Now I just need to order a skid plate….

Hey man, thanks for the video! Hope you see this, curious a couple years later how things have held up! Appreciate the work you took to film everything!

Drain engine first then the filter.