Видео

Will it work with a Mac?

Wow! What is the resolution of the prints?

My concern is that you have one chance to get it right. Printing on a transfer gives you multiple chances to get sizing, colors etc correct.

How can I do perf-cut with contour or kiss cut? What blade are you using? I am totally new to this please help. You make it look so easy. Thanks.

I'm hoping you can do a cell phone case tutorial but not on a cheap case. Every time someone does a phone case tutorial, the cases are the cheapest plastic cases available. OR a custom PopSocket would be awesome to see! THANK YOU!

Looking forward to the next video! You have both the printers I want to invest in so your videos are full of priceless information! THANK YOU!

Rotary possible?

How long did it take to print this design?

thanks

Amazing! Very creative ideas! before I take the plunge, I need to know: What is the longest you have left the printer idle between prints? how does the printing hold up after days of not using the printer? Any issues with the white ink? A+ video!

What vinyl do you recommend for stickers?

How fast does white and primer run out? I had this printer for only 2 weeks and have only done some small test prints ( for example i probably make like 12 bookmarks total) and white and primer is empty already Is this normal?

Hey just found your channel, really liking the uv printing. I was just curious, are the white guidelines something that the printer does for you and if not how do you do it?

Can you tell me if you do a conture cut then a perf cut do you have to pause the machine after conture cut to lower the blade in the blade holder? Love the video very helpful

Hey there. Just stumbled on your channel. Nice work. Re: template on the grippy mat, is that permanent or does the white ink wash off?

LOVE your channel and always great videos! With doing contour cuts, how often do you go through cut strips? Also, what is the cut strip replacement like? Is it difficult? Thanks again for all of your help!

I love your perf cut settings. They are way better than the defaults.

Great video. Just what I needed. I've seen mixed info online about the max height of an object - do you know what the max height is? Thx

Hello Angela! Love your videos! Can you make a video doing a name on a small tumbler? I know you can’t use the rotary, but I wonder if you can just print on one side.

Great tutorial Angelyn. I create my cut lines in Adobe InDesign using a different process, but works just the same. Thanks for sharing.

some info I have this printer and i print a lot so here are my thoughts: Before buying this printer beware that the INK cartriges for this printer come only in 220ml! The white color will run out within a month if you print or not. The printer will use around 4-5ml a day for self cleaning. The printer is cleaning itselft before, within and after printing and wastes about 80% of all ink. Unless you print more than half a day you will never catch up with the waste ink used for cleaning so be ready to send 500€ of ink to the drain. A 220 ml color costs 90€ and the white about 60€ .. for the bigger printers this is how much you pay for like 500ml... so the ink in this printer is extremely costly and most of it will be wasted. The other thing I really don´t like is the printer is missing very basic bed positioning buttons on the front. You have to readjust from your pc.. if it´s not next to it and just 5m away be ready to walk a LOT! A single print run if you print 1 item or full A5 will cost you 1-2€ so the print is EXPENSIVE becasue the printer will clean, and even clean again. Per day this printer will waste around 5€ of ink if idle and not used. The printer is Cheaper and has the same print quality is the top tier Roland printers BUIT. The ink cartriges are only 220 ml and will run out fast basically within a month (white) and others max 2 months even if you don´t print. The printer cleans itslef almost all the time.. it´s actually quite annoying. 8 hour cycle but if you print even more. Negatives: No positioning buttons on the front for moving the bed, Only 220ml ink, too much cleaningand most of ink wasted*. Positives: the software is great, Roland color palette! White and Primer cna be controlled separately in versaWorks or in Illustrator, Print quality is TOP, Somwwhat Affordable* I would expect an upgrade to the selfcleaning by some firmware to extend it to 12hours or at least to remove a few within printing cycles. A bigger cartridge would be strongly appreciated (at least 500ml). Especially for white. Tip on how to save ink if you print little: buy a mechanic electric plug timer and only set up the printer to run (give it power) 1,5 hours a day it will do 1 cleaning so you can be away even 2 months.

Do you still need AI to create cut lines with this machine? Can you use included software to do that?

Can you do it on Lego mini figures?

can you make round christmas ornaments on clear acrylic. one reason I want to get one of these.

Thank you for being clear and concise, what 6 mil vinyl do you use and where do you source it from?

How much does it cost ?

How often are you going through ink?

Thanks for the video! Where did you buy this printer? online or a Roland dealer?

Quick question, how do you print white with the BD-8 I use affinity but it’s refusing to print white

Love your videos! Here's an idea for being able to print the roof on the angled Lego piece. Maybe try putting some Play-doh on the bed and then pushing the Lego brick into it at an angle so that the roof is parallel with the print head. I just got this printer so I'm loving your content. Keep it up!

Angelyn, i have a request. Can you please try printing on a polymer clay object, like a charm or an earring or any small flat or curve dry polymer clay object as that is definitely going to expand the Use Cases of UV printing. Plus That'd be first on the internet.😊 Keep doing great work. Love. ❤

Angelyn, you just made me justify buying a $10k printer, so I can customize all my lego blocks, lol. Great idea and great video.

Nice video thanks ! I would like to know if it prints on mirror , shinny metal, rubber items like rubber bracelets or rubber slippers or erasers, and does it print on 3D printed objects ? And is it scratch resistant for these materials ? Thanx again

Hi how r u how do i get roland product for only lease for one month .Do u know kwow any who is selling used.

Wow sooo smooth an easy and thank you for this video it helps out sooooo much

Amazing that you’re working with one of these units. I can’t justify the expense yet at 10K. You must have a large volume to be able to get a return on that investment. Great job!

Great tutorial! Thank you

A very great tutorial on how to adjust the blade and check a few different settings. Great work, keep the videos coming!!!

Gǹ Ongerggs

Do you need to apply a seal coat on wooden coasters since there is no gloss option in the bd-8?

Were you still planning on printing on Lego pieces?

That's awesome. Even the small type is still clear to read.

What size is the working bed ??

Thank you - I would love any tips for Illustrator!

Can you show the cut feature if you wanted to laminate your stickers first? The only example I’ve found, a sheet is cut and laminated then the stickers are cut out using another plotter. Can you show this without having to buy a second machine?

Great video 😊

Awesome!!!! They turned out looking really nice and the tab makes it easy to peel. Great tutorial on how to make the little tab as well. Thanks for sharing.

Hello, I'm enjoying the video. Can I use it at home? I'm worried about the smell or noise.

🎉🎉🎉🎉 thank you!!!!

How did you solve the overspray issue on the sides of the product?