Видео

haha , cheers plenty more in my other vids

ive got too go into the menu and hit 3 buttons too reverse , but there are a few on ali express that are set up for one touch i think........ this suits me and i got it local incase it gives any trouble

if you have a b series engine already its easy as piss , if its an h or f motor , you need too find a bell housing and b series input shaft too swap ....... the 15b is strong as hell , but not cheap , but they basically bolt strait in , radiator , gear box , and everything with the b is plenty too handle it .... all you need too know is here facebook.com/groups/341040909615842

i realise this , we were checking how well the poly would hold compared too vulcaniseing , and when hitting rocks in jet boats the forces might differ some what from what a car gets upto

Yea , it surges abit at real low revs , but when using the lathe you hardly notice if at all... range is about 200 too 4000 i think ... its also got a 60mm pully , so if you went down too 50 or 40 mm you could run it faster and avoid any surgeing......

@@mohawkc77 Yes Sir I was just trying to be funny??? but as usual no one gets Me🙄

yes , my pzj70 1990 short wheel base..... the 3b and 15bf were in my 1989 bj75 ute

hell , you aint seen nothin yet ....

@@mohawkc77 hey it's really cool, I'm not knocking what you're doing, but literally it's all fun and games until your headed to the hospital either dying or still alive. I don't suggest either one. Houdini died doing what he loved. Kobe died catching mad air. Sure, there's risk in everything we do. You don't know you're there till you get there, might as well take a couple stupid simple precautions to prolong doing what you love to do.

@@adamhorton1601 no its not risky at all.. water cant compress thats why its done this way... if you look through the coments youll see those who actually realise this

@@mohawkc77 just saying high pressure injection into flesh is a thing. Anything over 100psi according to OSHA (for what that's worth) is considered high pressure that can cause injury. I understand the energy potential is not much with a non compressible, but diesel isn't compressible either and people get that injected into their hands unknowingly touching a pin hole on an injection line.

cheers , still singing happily too and its had arseholes.

it pulls at first , then cools back the otherway past where it started... im heating it on the high point .... as an example if its 5 high , it might go too 10 high as you heat it , then shrink back too 2 or 3 high as it cools

nup nup nup ... its all about the content , not the camera , or phone in this case

in the back of the head there is a bolt on plug , weld a block of ali too that , then chuck the internal end in a lathe and bore it out too suit you distributor on the back of the cam , unbolt the reluctor wheel and weld a 19mm ? socket too it ( or similar ) chop a slot in that , bolt it back on too the cam and your done .. its all documented here www.jbnz.co.nz/yabbse/index.php?topic=32094.75

@mohawkc77 thank you very much for the information hope I can get it's done before summer, winter here right now in canada

are you putting it in a boat ? @@dainguyen-xe8un

@@mohawkc77 yes its gonna going my 12 feet jet boat

I'm a full-time welder. If it run I will sent the cylinder head to machine shop and get porting

new zealand

@@mohawkc77 Ha Ha , soon as I saw the landcruiser and a couple of blokes doing silly things I assumed it was NZ. Surprised the undercarriage wasn't held on with No 8 wire.

nup nup nup

Kill switch ! I was surprised he had a life jacket on! LOL

I think it just stays attached. Give this guy a little while and he'll figure out a way to drive the wheels and he won't need a trailer or a tow to the boat ramp any more.

its just an old piece of ladder with wheels bolted on , it wont float far @@luke_skywanker7643

Geeze! You've got quick eyes. I didn't catch that the first time when I watched it. I'd like to make something like that out of a PWC and put a fiberglass Pegasus or pig on it. Just ride it around 'stylin.'@@mohawkc77

artistic expression 😁

nup , was always going too be rewelded and cut too fit the the hole it was going in ... just needed too hold together for expanding

Perfectly safe..actually

yup , but we knew that

well ive flipped it twice , so cog is a big deal too me 😆 ... you really cant compare a ski too a propperly built mini jet boat ... its built with 6mm ali bottom and a 7 bar intake grill for good reason .. your jetski hull would basically desolve in the water we boat with these

@@fishkeg its the coolest boat in the world 😆

thanks

yes , raw water cooled .. pretty simple too set up .. water goes strait too car water pump from the jet unit , excess water is diverted too the exhaust , and as it heats up , hot engine water exits too the exhaust thru a thermostat housing mounted at the back of the head , i have another video here on youtube that shows it better ruclips.net/video/MuHfn-f4NqI/видео.html

@@mohawkc77 oh thanks, i apreciate that

Pretty easy , you would need a fly wheel from late honda civic , make a bell housing and bolt on a box , its just a motor after all , just do it www.jbnz.co.nz/yabbse/index.php?topic=32094.msg232288#msg232288

I have a video of the previous engine , a 2004 suzuki m15a with the same distributor and a couple of shiity old strombergs on it , and also video of both engines in the boat running on this channel too

ha hs.. we got it all out , bloody phone ran out of battery