Видео

Beautiful work!

Beautiful work...wish you were near me in Jersey for install. Question, how do you get this large tile up to the 2nd or 3rd floor? Is it manually with several people up the stairs or you use a lift through a window? How does that practically get up there?

Where can I get this?

You make it look so easy I don’t have the expensive scoring kit but I ended up returning a bunch of 1/4”x3’x6’ panels that I got for about 1/3 of the price because after trying several ways of cutting it would just snap. I felt like it would break just by looking at it

How much a job like this can cost? It's wonderful

Awesome 👍👍👍👍

Do you ever mix the thin-set mortar with a higher water ratio than specified in the TDS because manufacturers call for a looser consistency for embedding the mat than normal?

He is getting evidence for that last felony.

This is another level. Lol is not for inpatient tilers. You made the niche cuts on-site, cause it was broken-easy carrying it?

Good job. You are amazing.

Thanks

Well shot well done video and helpful too.

what grinder are you running and are you concerned about it getting wet?

That’s impressive!!

How much does something like this cost?

I have installed a schluter pan and used all set to put down marble hexagons, but have not grouted or sealed the marble yet.. I would like your honest opinion on what I should do forward.. I’m trying to avoid the “wet” marble that you talk about.. I wish I would have known this , obviously before i thinset the marble down. I’m just a homeowner and have spent ridiculous hours on this master bathroom.. Thank You,

Very good 👍

Looking great .. what a mission that job was for you I'd say ..nearly their well done 👏

ive never even though of how much of a pain in the ass laying big tiles would be, how often do they break?

ive never even though of how much of a pain in the ass laying big tiles would be, how often do they break?

I would to install Dekton slabs for my bathroom remodel from a tub to a shower conversion. What is your experience in regards to the thickness (most durable) that is best used for the shower walls and the shower tray? I would like to use matte slabs for the shower walls. Would you know if the matte slabs are as easy to clean as the gloss slabs. Also, are there instructions on how to cut and install these slabs for my contractor? Are the slabs readily available in the United States?

Question boss, the thinsett directly to the playwood won’t be a future problem,?

SMH. No one working is actually wearing safety glasses, a mask (for what?) or ear plugs, yet this video stops to Virtue Signal anyways.

Wow! Amazing job!! 👍👍👍

Beautiful work

Just curious why use blanke system?, if others like Ardex ui720 also a great system. What makes blanke special?

Дай Вам Боженька, чтоб руки не болели. Ответственный и нелёгкий труд!

Garvage material, it brake so easily that if you need 2 slabs for the proyect, just start thinking about buying at least 3 because most likely one is going to break. Plus you can’t polish the edges, the only way to make them look good is by doing a 45 cut and glue a return on it. There is other much more resistent materials that can be polished saving a lot of labor.

Very helpful info-thank you for posting. Could you seal the tile BEFORE adhering it, or would that cause an issue?

The call in 3 years. Customer need a cracked tile replaced due to settling of framing. So dumb to put something that large and nonflexible on walls .

Is kerapoxy an equivalent to Spectralock pro? It’s interesting how you finished these joints compared to just grouting them normally.

I have this issue with my current shower that was redone. From what i saw then install they used sand pack or whatever then put the marble right on top and grouted over the tile. He was unaware that marble had to be sealed but i caught it before it was an issue and sealed it. Is the discoloration something i have to have them pull it all up and fix or can i live with the color issue or will it get worse and cost me more later?

The same without separation

Why don't people run ufh cable under the shower area? It's the most important area to warm!

Is that a crack in the tile when youre drilling holes?!

That pony wall is worthless

Beautiful. Would love to see the setting of those enormous wall tiles as well.

NICE WORK! Ever run into an issue where 24"x24" tiles are actually 23 5/8"x23 5/8"? They are slightly smaller than the kerdi shower pan and I'm looking to do an envelope cut with 4 24"x24" tiles with the square center drain. I think I'm going to have to cut the pan down but 1/4" all sides and make sure the rough framing is based off that rather than the original shower pan size but it's such a small amount. Be nice if they just made the 24"x24" tiles true to size.

Great work, i enjoy watching your videos! Tile work is an art and i appreciate your attention to detail! Tile guy's rule! Cheer's from Southern. California

More easy to install that membrane

I been trying to get one for a long time

A professional will bend you over when you get the bill

Great video! Quick question. How did you bond the sheet membrane to the top of the ebbe drain?

Thank you so much for this video - we are looking to use large format tiles and went to a store today who told us our bathroom was too small and it was impossible as it would require removal of the roof and four people to move the tiles. I tried explaining that didn't seem right and the sales woman just told me she had 30 years experience and I didn't know what I was talking about. Our bathroom appears about the same size (it's a shower and toilet room like this) approx 1500cm by 1750cm by 2400cm high with a 620cm door way - is this similar to this one (if you happen to see the comment) would love to hear any advice or thoughts (obviously we will hire a tiler but she literally told me don't even bother calling them as they answer will be no).

Amazing work! Question. Can I cut a 36x72 porcelain tile with circular saw (diamond blade) without water? Also, can I not have any gaps in the tiles? It’s for a fireplace surround so it’s 3 large pieces (top piece and 2 side pieces).

I live near there and am looking for an installer for an outdoor patio like that. Who did that one and can you recommend anyone? Also, what is done to prevent efflorescence and what is the "grout" material?

Great work man what epoxy did you use and also what spray did you use

Has to be one of the most bulletproof showers I've seen. Ever.

Офигеть! В нормальных странах уже всё изобрели😮

how much did all of this cost? i know marble is around $3000 just for a tub surround shower but you did a walk in shower ?? allthe walls. and vanity wall too?