Видео

Some maintenance tips for others maybe having vibration problems. Don't assume the rotor bearings are ok. I've just changed mine ( along with the slipring ) and the difference is astonishing. I had gotten used to a fair amount of vibration coming down the mast and echoing down the hillside towards my house. After changing the rotor bearings the vibration and noise has completely disappeared. Like car bearings, these can create a fair old racket and a lot of vibration but seem quite smooth once theyre off the vehicle. Free play in bearings is sometimes not easily detected but the symptoms certainly are!. Thanks Kilkenny Homestead for all the help. Terrific video..

I was enthusiastic until I reached around 6 minutes in. That looks like no job for a DIYer such as I... 😂

You were right about the hardest part being the positioning of the end caps! What a b%^&* of a job!. I tried your method of using 4x2's with a slight mod. Used two threaded bars & nuts to pull the timbers together. Trick is to tighten up so that the turbine is well jammed in place.. Then used a heavy leather mallet to nudge the caps. Very satisying to hear them plop into place!. Thanks so much for this video!. Pity that ista don’t do a maintenace manual/video. A must have when slip rings go out after a couple of years.

Why the angle?

I did find the parts for the thing below (that's rotating the solar array), but what's part do you have that's from solar array that's connect with the top of the part? Didn't talk anything about it or didn't show it either. So that's why i'm wondering. Also i know you have newer version of this now, but i wan't too keep it "old version". :)

Love your video thanks very much !

Vevor has no helpful support when there is an issue.

Thanks for your help. That worked a treat!The top bearing of the dual set was fine (6008 c3's ). The bottom one was really badly knackered. One thing...do you have a link or model no. for that uprated slipring ?. Hope xmas has gone well. By the way, my two i1500s have knocked it out ot the park for generation, way outstripping my panels.

You don't happen to know the factory slippering part number do you? Or at least the factory ring diameter?

Any tips on how to choose the right port on my Asus laptop? Tried all 9 ports in the sotwares dropdown and there's no "port & lpt" section in device manger.

Shouldnt have spoken too soon. One of my i1500's went completely nuts in the storm a few days ago. Sounded like a helecopter !. Thought it was going to break up. Took it down today, in between peeling sprouts etc and discovered two problems. The slipring was completely shot. No slipring meant no braking. And the vertical swivel bearing is a bit knackered. After a degree of brutality and moderately bad language I've managed to get the whole machine disassembled without destroying it. Ive got the two big circlips off the vertical spindle but I cannot get it to budge. Did you whack yours out or press it with clamps?

Sometimes these manufacturers offer different voltage setups ignoring that the torque might be completely inadequate using the same generator.

Hi , im wondering about your turbine , i have the 48v i1500 version , ive seen it at over 3000watts, but i find when its lighter winds ie: 10 -15 mph its spinning fast but Producing nothing . Is yours the same as in it needs strong wind to produce? Thank you

The sound is poor

Looking forward to your next projects on the channel

Good to see you back , much love to you and your family

Thanks for the tutorial

Wondering if Wago connectors would be better than the ceramic connector block?

Is this firm ware generic? I have 3 x 8kw voltacon units, same the one in the video. Voltacon have said the firmware is specific to each serial number, however they have sent me 72.72 for 2 inveters and 46.82 for another. Surley these need to be all the same as they are paralleled together.

I hope it wasn't British Battleship Grey lol

excellent job

where did you buy it??

I'm planning on hooking up my Sterling Battery to Battery charger to my 110Ah leisure battery, but the output is 30Amps from the charger... do you think I should use a shunt resistor to keep the current at 20amps or so instead of the 30Amps? Thanks for the vid!!

I went the folder that has the soft and app plz shat it

Ebatlarını yazarsanız daha iyi olacak bunu yapmak istiyorum lütfen

WOW

Ok I just did this to my hen. She wasn't very happy about it but it's not like she has the energy to fight me over it

Great video bud 🤝 Thinking of a self install myself in Dub

Howdy storm Bert get on, i turned break on when 60mph+ passed on Saturday 12 to 3pm then 22 to 4am

Ciao io ho un voltronic master power omega 8k, ho problemi che la mattina si blocca per 2 ore a 90 V e non va in produzione versione software main cpu u1 46.08 e secondary cpu u2 112.15 e' possibile aggiornare il software ?

Irish climate 9a?

This one connected to an 250volt/100amp charger will br an killer

Could buy bigger blades and make it even more efficient

Thanks!

❤

👍

Thanks a mill

😂 Geez Louise

nice simple pallet recycling idea, i will do it next week for my garden. thanks for sharing.

His pallet must of been made different from mine. It took me about 3 or four hours just removing the first three boards with just a hammer and pry/crowbar Also I have hand tools. No electric tools

*All practical tests of ground-based small wind turbines show: 1) They hardly produce any electricity! 2) They do not last long!* *With solar panels you can generate at least 10 times more green electricity with the same investment & time expenditure!* Reliable and almost maintenance-free for at least 25 years! On the other hand, 9 out of 10 small wind turbines stop working after just a few years due to the extremely gusty winds close to ground.

3 blades will let it spin faster and spool up quicker. I got the I2000 but I gotta put my tower and stuff up cant wait 😁

GOOD !

😮 I love this! Can't wait to get mine done like this!!!!

I would like to comment that it’s 20 amps per phase. This means you have AC, and it is sufficient for this wind turbine because special cables have been used. These are not ordinary cables; they are gold-plated cables. The datasheet for the slip rings can be provided at any time.

4 minutes in.. idea To cut the pipe in half with a piano hing holding the sides together. With rope/chain/springs bringing size to grab force. Maybe??

Ya know… the chicken coop might need some tweaking…. But that steel frame is a great start…. It’s the perfect size.