Видео

Great video, thanks!

Thank you so much awesome video much appreciated 👏 😊

Those pennies probably add up to more than what youtube pays

6010 just sucks! It always has, always will. Why use 6010 when you can use 6011?

no one ever says welding easy on the body, vid playback always shows the contorions weldors force their bodies into

Great work artist ❤

My husband and I just fixed our Amana drying machine Thanks to this video Very helpful

Thank you so much for this. Dryer belt broke Christmas Eve night. Stuck all day Christmas with wet clothes, lol.😂

I already subscribe to your channel idol

thanks you are the only one who showed the ground needing to be hooked to the pos side!!

Why did my drum fall off ?

Now how do you put the front back on

Thanks a lot for making this video. My stupid dryer started making high pitch squeaks, and I thought it was going to a huge pain to change the belt. But no, you made this very easy and simple. Thanks a lot for the instructions. Thumb up

Thank you for this video. I never even took apart a dryer and today you helped me replace the belt and showed me where the tension wheel goes and how to run the belt through it.

One of the best vids

5/16 or 1/4 inch

Followed the instructions and removed the wire bit you had issue with with a Phillips by unscrewing the plastic bit attached to the door

Hi I have a question I bought this welder but I was surprised it doesn’t have foot paddle for Tig weld i confused some of them have and some not so what the paddle do give voltage? Thank you for your time I LK&SB

My XT8000E starts usually very good but I use non ethanol gas and a fuel stabilizer. The hour meter failed though at around 23 hours I believe and had to buy another and found they are rather high priced. For some reason, it wasn't designed to charge the battery when running which is a flaw. If you read the manual, you will find the valve clearance is supposed to be adjusted at 50 hours. If you want to do the valve adjustment yourself, it's best to get a service manual. It can be challenging to get a service manual though from a dealer I found but a digital pdf version doesn't cost anything. If you read the small print about the specifications, you may be dismayed to find that the maximum wattage is limited by the air temperature above only 60 degrees F! So if you use it during the summer where can get rather hot out, the output will be less than the rated power. It decreases 1% for every 10 degrees F above 60 degrees F. The output power also depends upon the fuel BTU content and also the elevation.

Roughing in a bit of “Youre Gonna Go Far Kid” and “Teen Spirt”

Piece of cake. Thanks!

What a joke. I lay on the ground, put a socket in the nut , and 6:20 Wah lah. Blade is off. This is for nit wits I guess😂. NEW BLADES ARE OLD AS CRAP😂😂😂😂

For anyone who winds up here with a NED5800HW model, this repair is done by taking off the top and back panel. Hopefully, I can save someone the hour I wasted trying to get it from the front. 😅 The pully routing part of this video was clutch. Thanks, OP!

I needed this video thank you! 🙏 🎉

This totally helped me out. Thank you so so much!!!

You have horrible form

I have the exact same dryer, only difference is I can take the wire harness apart, just pull up on a small tab and pull apart..

thank you so much looks pretty easy my 83 year old neighbor asked me to take a look at her dryer for her i'm sure i can help her out now that i watched your video

Good work

Awesome tutorial!

Thank you so much, $15 repair. Quick and easy thanks to your video. You're a good man.

Thank u so much two girls just did a big girl thing thanks to u king

Thanks for the video. I was able to replace the belt on my dryer (same model) thanks to it. Got a repair kit on Amazon that included a pulley.

After you get that belt on, change the battery in that smoke detector 😅😅😅😅😅

I had problems with the accu set screw pin shearing off and the 4 mode setting switch just fell apart. I got it back going though. Thank you for this. I been welding over 40 years. A good paying trade

To make it a lil stouter you can screw the tensioner down then put a long screw in that slot to the left with a string going to the tensioner then tighten down the screw.😅

The wiring on the side does come off!! There’s a tab ur supposed to lift up to pull it off

didn’t think i’d b arc flashed from a video

You definitely need to get it wet before you smash.

Just fixed my grandmas dryer in like 15 min cause of ur video thank you !!! Saved her a ton of money !!

what is the clanging noise?

Dryer back working!! Spent under $12 on amazon for a belt. 💯💯💯

You’re the best thank you

Do you need a foot pedal for this machine for tig

5/16

I never comment or like videos but this helped me out so shout out to you . Total cost of this was $15 so thanks my guy!🫡

Thank you I was getting pretty frustrated pulling the back apart lol

Exactly the vid I needed thx👍. I'm about to replace my belt; and I can only imagine how many guitar picks I will find😅

93 octane gas is not premium gas that automatically better for your engine. It is better for certain engines like high compression engines or engines that are not running well. This is a simple small engine and you are not taking extra care of it with high octane gas, you're just wasting money. Some automobile engines not designed for high octane gas will get a check engine light from high octane gas. More expensive doesn't always mean better.