Видео

Thanks so much for this video. Was considering purchasing this monitor, but after I learned that you can't set the parameters from the touchscreen and get the values to 'stick', I decided to pass. I think I'm going to build my own monitor from an Arduino.

You can jump pin 1 and 3 on the LightBoard and wake the BMS

Will this screen work with JBD BMS that has serial input or output

Daly=junk.

did you ever get this BMS to function properly?

Did you have any luck with getting the settings to stick? I’m sitting with the same issue

PW is 123459. it will complain. then use 123456 and it will work

Could you have put the outside and inside lights on dimmers?

What thickness is the particle board and the aluminum studs? I guess I am asking is that particular window made for 1.25-1.5 thickness? What is the window brand? Thanks

My Daily BMS & Touchscreen will not turn on

So far my second Daily BMS Is Garbage will not turn On “ DO NOT BUY “

PLEASE !! Does the DALY BMS balance the cells? And if so, how many compensation amps does it send to rebalance the cells?

I believe the password is 1 through 8

Very interesting!! Could you post 3D files?

You totally missed the biggest "problem" of all: the Comic Sans font in the BMS UI

This video by Daly might help with the touchscreen config setup password issue: ruclips.net/video/uVzdiTusfK4/видео.html also it looks like you can manually wake the BMS if you have their SOC indicator installed, apparently it has a button to wake the BMS up.

For the para setting to stick even if its off and when you turn back on. First go enter a wrong password than a screen shows wrong password. Then go click on set password change it type old password 123456 than new passcode at ur will. Set it change your screen timer from there. Switch of and try switching on it stays.

Are all day BMS smart ?

As always, if it can go bad it will.

Their for a second I thought this video was going a different way lmao

Bwahhaaaa! Almost spit out my coffee..."Put that in the clip" as he slams his head on the window. Ouch!

why to mount a fragile touch screen if you got an app phone? the touch screen do not work the same time time than bluetooth and you know it stops working after a short delay if you dont charge or discharge. Is too fragile to handel with the case.

Thanks for sharing your knowledge with us. We are doing a tramper as well and can use all your tips. Looks great

nice build, and I love the Gamers Nexus Mod mat

Thanks for the cool video, I will attempt something similiar and this helps a lot. Cheers!

If you set your Screen timeout to 65535 that disables the screen timeout :) Also if yours is the same as mine the J6 Connector, “S1“ pin (Pin 3) on that connector wakes the BMS when shorted to ground, connecting a momentary push button there will wake the screen ( like a reset button on a PC) EDIT: it may be the J5 on yours, sorry I'm trying to help it was frustrating for me too!

Great video. Do you have any other videos showing how you mounted the XT60's to your template plate?

Your link to the english firmware is not working

How did the luan take the paint? Can’t wait to see the finished product.

Just a idea how about using a GoPro on your head when you work

OCD'S SUCK

Interesting and useful overview. I'm just setting mine up and not got the screen showing yet so this has been helpful. One thing I noticed on my display is the one connector splits into 2 for connecting to the BMS. One goes into the UART but I'm not sure on the other one. Guessing into the Chines labelled port which translated says host computer. Was this the same for your setup?

Great video. I thought this would be the ticket to get MY emergency exit window installed, but having all kinds of trouble. It's a window purchased off eBay. Need I say more. Is anyone available for a consult to tell us whether we can make this work? The trim ring does not seem to fit, or we just don't know the right way to attach it.

0123456789

I,m having the same problem. 4s LiFePO4 version. No com at all with PC. Some parameters can be changed with the BT and phone app, but not all. Still searching for solutions. Nice Power box though!

Set the off timer to 15300, and put a switch in the 3v3 line of the screen. The BMS draws next to nothing while awake, and the screen will always be available, by simply flicking on the switch.

niiice ;)

Can you share 3D file?

Observations and comments. FYI I have a 250A 4s. It may have different I/O ports than yours, keep that in mind when I reference some of the BMS ports below. I've measured the current draw of the screen at about 100mA on a 4s LiFePo4 battery. You can use a 3.3v FTDI or other generic USB-UART adapter if you have one. If you don't have one, get one that is 3.3v/5v selectable. They're handy to have around. You need to use a different UART port on the BMS to use the Sinowealth software to set parameters. It's a 3 pin port, probably labeled PC or Monitor, probably in Chinese. There are many more parameters that can be set with the software than are displayed on the screen. The SOC meter goes to 100% when the cell voltage reaches the charge end voltage that is set. You'll need to set it with the software. After that, it tracks the state of charge by measuring the charge and discharge current and referencing the programmed capacity. The ammeter can be calibrated and the minimum current that is registered on the display can be changed with the Sinowealth software. The minimum current parameter is DfitterCur. You should set it to zero before calibrating the ammeter. I've noticed the ammeter has a lot of jitter in it's readings. You'll be able to see this in the info screen under CADC Current when DfitterCur is set to zero Calibrate the ammeter using the CADC Gain and CADC Zero parameters, then set DfitterCur to something reasonable like 1000mA. The screen doesn't turn itself on or off. If the BMS is activated and awake, the screen is on. If the BMS goes to sleep, the screen goes off. When my BMS wakes after going to sleep, it doesn't communicate with the screen properly and only updates the info on the screen about once per minute. To correct the problem, I have to disconnect and reconnect the balance connector from the BMS, and then reinitialize the BMS. To initialize, the BMS needs to see charging current from the P- to B- cables, or momentarily short the 2 pin connector on the BMS. To wake the BMS, you can use charging or discharging current, or short the 2 pin connector. I'm curious if your BMS has the communication problem after waking from sleep. You can unplug and replug the screen into the BMS at any time without issue. If you don't want the screen on while you're using the battery, you can just unplug it and save 100mA. You could put a rocker switch in the 3.3v wire going to the screen if you want. It might be a good idea on a relatively small pack like yours. My screen doesn't have the password screen. My firmware might be different than yours. My screen came preloaded with English firmware, and I haven't changed it.

I can not find that monitor any where

You should not have covered the front left vent that one would keep the dirt and dust out while traveling with the the pressure it provides

Well managed. Looks great

Are you able to change parameters with the screen? I have a 250A 4S Daly with the screen, and I can only change parameters with the Sinowealth software.

lol I just built a 60ah 12v pack using 48 of the 5000mah cells from batteryhookup. Has consistently tested at 70ah @ 0.2c discharge. Was so thrilled with the build that I ordered another 16 cells to build exactly what you've created in the same Apache case. Determined that I could fit a 24 cell pack and fit the BMS in the lid recess, but there'd be absolutely no way to install panel mount connectors of any type. Good project, happy I found the video. I'm stumped on how to secure the 48 cell pack in its tool box, and the upcoming 16 cell pack. Has been a lot easier with my prismatic builds but I haven't had to worry about spot welds popping off with those.

For your viewers, never put silicone on your trailer. It will dry out, crack from the movement of the trailer & is hell to remove. There products made for RVs called proflex.

What is the name of the screen? Can it be used on any BMS or just Daley? Robert

Fyi, those nickel strips from that supplier are ..steel.. with nickel coating. Just scratch them up and drop in hydrogen peroxide for a quick rust check. I have never found 32650 2p pure nickel strips sadly and steel has a fraction of the current capacity.

Very nice Build. :)

So helpful! I want the exact same window, but it seems to come only in 2" depth which is a hair deep for most cargo trailers. Was that how deep your window was?

So, your trailer doesn't have rivets for the skin - does it use glue of some sort, I assume?