Видео

Nicely done, sir.

Good job, my man 💪 I really needed to see this now Thank you 😊

I got 5qt from my 09. Think it was overfilled.

There really isn't no need to cut taper the front ends of each board at 45degree angle makes no difference cutting them.

More advertisements than content

Great video on how hard it is to work on a 2.2 liter. Now I need to find where the rail is.

Thankyou for your help, what's the tool called for tensioner bolt

I went for about 2+ years with a finicky front O2 Sensor on a 2002 Solara SLE V6 1MZ-FE (MCV20). No misfire though.....It would trigger the engine warning light but reset to good on the next startup then come on again on an idle. Gas mileage did go down as I have driven this car for 22 years but not to the point of expensive repair before my 300,000 mile service. The rear O2 sensor under the car is factory still and they rarely go out. As to the recent real problem(s) was a misfire started a month ago on startup in the garage due to other factors according to my repair shop. I parked it until getting towed to the shop. Reasons were oldish spark plugs, bad ignition wire set, and two bad direct ignition coils. My car shook with two cylinders out I thought it could be about 9 things wrong but in reality this was not a heavy fix. Repaired now and ready to chase after the 400,000 mile mark. Mechanic said the V6 Solara is a half a million mile car, possibly more.

I have a 2001 solara it's misfiring a bit when I pass 40 -50 mph and when am parked it misfiring a bit as we'll i got a code p0302 and p0300 which coil and spark plug is it ? Can you help me out

Thank you brother I (we) appreciate this video! I was about to send the flange I purchased back until I saw this and seen how it is mounted. You saved me the headache of sending stuff back and searching for the “correct” flange. Have a great one 🙏🏼

This was a very very good video

Common failure is using a plastic flange especially from auto zone or cheap Auto stores, the heat will warp the flange and it will bend and create a gap for a leak, USE ALUMINUM/ METAL flange.

Thanks for sharing your video. It really helped me. GBU

Is this the same for one with a 3.6 engine

I really wish I had a VISUAL on how to remove the bottom metallic colored line running to the bottom of it. Please reply to this and tell me.

thanks for identifying the problem. I used an ohm meter and checked for continuity from all the legs of the chip on the top side (since the bottom side has epoxy) to the traces on the circuit board on the bottom side. I found that pin 10 was not stable like yours! I melted the epoxy on the tip with my soldering gun and connected a wire to it to another point in the circuit. Works now. Thank you!

Dang they sure made it easy to get to the dang injectors!

Hey my name is Lanekka Joiner I live in Dallas and have the same problem with my 2003 volkswagon passat gls sedan 1.8L front wheel drive are you close and could you please reach out to me about this if you don't mind

I can’t get the heater hose on when I put the o ring inside

Youve got a lil Hank Hill in your voice Ill tell you wut. Thanks for the informative video. You rock my guy

thanks man you saved me so much time!! Quick question though do you recommend replacing the whole coolant system of a 2.0L 2004 passat? my engine was leaking coolant, and i have replaced thermostat/water outlet housing. Im asking as ive heard its common that the coolant completely corrodes the plastic cooling system parts....

Great video I got mine door panel off in minutes and without scratching the plastics that’s what I was mainly worried about

Bom dia tenho um seat ibiza de 2010 1.2 gasolina e quando dou a partida liga a luz do controle do peneu vazio e a luz de ESP e o carro perde rendimento. Ja mudei o sensor de rotacao e continua igual o codigo de ERRO E O P0321 seat pf ajude me😊

Thank you very much for this video you did an amazing job and you have helped me out greatly

Yes I agree this is the best video of how to remove and replace parts on a vw . Thank u Randy , u saved me a lot of money and time for getting things done on my vw passat. But I do have a question does the commy valve need a gasket when putting it back?

2006 nissan sentra sitting at 154k miles,an same dam thing is happening

Did you have to adjust the regular? Did it just work after installation?

You said twist and pull on the plastic clamps the attach cables to the bracket at trans . There is an arrow on mine. Would you mind exlaining where this arrow is suppose to point in order to release them ? And im twisting but it doesnt appear to have any threads.

8 years later and this is still helping people. I soldered pin 10 and it fixed the issue. Mine also didn't look bad. Thank you!

Great video. Thank you. My 05 started leaking at the vacuum hose to the manifold. So I'm going to be doing this job pretty soon

One of my favorite spots ❤

What are the symptoms of broken cables, what are signs they’re about to fail? I have a huge amount of side-to-side slop in gear, seems it’s getting more difficult to get in gears

T30 torx bit? Did you relief fuel pressure with removing fuel pressure relay or release by fuel pressure line?

What do you think is the best transmission fluid to put in there?

Excellent video! Question for you. My wife has a '14 GSR with the 2.0 TSI. Do you recall a second coolant temp sensor on the water pump housing? I'm getting some competing info online and want to try and confirm before I pull the intake manifold.

best design i've seen! thank you sir! i would've made the stop board a little taller though for safety..

Thank you for help so cable go 6 to 3 then 4 to 1 then 2 to 5 right

I hope your wife got rid of this car by now. I have a 2012 VW beetle turbo and this is the worse car every 3 to 4 months it needs a major repair. It's in the shop now get a new intake manifold for the second time!

Cool video !👍You really explained it very nice! Teacher!!!

What size torx bits does the bracket take?? 7:10

thank you!

Hi Randy we always learn thanks for your time l hope some day l try oh l like it your tire looks like it my hahaha have good day

I'm going to give it a try just like you showed me, thank you brother 👍

Que bien 👍

My only question is what water pump did u buy

Zajebiste

I’m having the same problem does it throw a check engine light and does it sound like metal hitting plastic?

I’m on my 4th round of this, they just keep breaking at least once a year, this time the spring and plastic housing gave out on transmission end

Incredibly appreciated awesome

I turned it sideways and the mount came out