Видео

I also installed this version but there was a problem in installation.during installation critical error occur what should I do?

I installed this version but even after it's 100% done I cannot find any of the products... workbench fluent nothing... what should I do?

hi quick question what will be the average heat genration rate of the cell

can i get the saved file of this experiment

Amazing tutorial, but what i am wondering is: does your data correlate with the one from the paper?

I installed 2024 r1 five month back, there is any need of to install 2024 r2 for Li ion battery thermal analysis

constant heat flux call transient? why

where can i get the geometry or the dimensions of the geometry

I think you need to take in account the PCM solid phase because you didn't take it. You have only enter the properties without using it, within the physical model.

hi bro . bro the total temperature in the battery is 300C.is this correct because i am finding some reference to find it . can you please tell me or quote some paper

hi, what is channel wall thickness?

Hi can you tell me the research paper name for deep study please

Can you give the reference research paper??

Can you upload some tutorial of explicit dynamic structural like a car banging on the wall or a ball bang in the wall...

Amazing bro

How to make that geometry? Make a video about it

have you specify the discharge rate of the battery in the simulation

hi can you tell me what is the specification of each cell in the battery and also if you have the relevant research paper it will help me a lot

Don't you need to select the contact region temperature as room temp in boundary condition of each contact region ??

Thank you for the elaborated explanation

kindly can you tell me that if i change the time for the simulation solidification and melting can be observed ?? if applied the same methodology ??

None of your simulations have actually showed contours of solidification and melting. You should be more detailed in discussing results, if we can't see solidification and melting then there is no point of PCM simulation.

hi i can't see the google drive link here

can you please tell me this battery can be used for the automobile i mean car

hello sir , u only give heat flux 0 and contact angle 20 on wick geometry?

Can you provide me your contacts

Sir how much time did it took to load for you ? (Running calculation) What are your computer/laptop specs ?

How was your upper layer visible?? I designed a battery in ansys but i had my top layer covered and cells weren't visible

Really fasinating, Well done dear. ❤

I have an issue, @5:12, here the red and blue arrow lines are shown but in my case , those are not showing

Thanks for sharing. I have some questions, 1. Why don't you use volume average for reporting the result? 2. I've followed all the steps in video, got the similar result, but as I add new plane to see in to the cross section in interior of the cell, I found that there is only heat transfer on the surface, but in the interior zone, there is no heat transfer.

sweep path must contain exactly one chain error coming while sweep

Thanks for sharing！ Why do you need to setup two materials for pcm?

Hi, Why in cell zone conditions did you not set water as the fluid? Thanks

Can you make videos on thermal modeling and cfd simulation on various discrete devices of power converter module.if you will make it ,it will be very helpful for me and another students. Thank you so much for above video.

Thank you so much 😊🌹🙏🏻🙏🏻🙏🏻

Thank you so much 😊🌹🙏🏻🙏🏻🙏🏻

sir can you share reference paper?

Sir, can you compare your simulation results with original paper.

drive.google.com/file/d/1y617-7ZhEeNmlvcWlGdiQR2thGnVISkD/view?usp=drivesdk Please doctor, can you explain how you get these values ( heat generation) in link

how to modelling wick in ansys fluent? pls help

Can u please share the title of the reference paper?

Exceuse me, i did my assigment it's quite the familiar to ur project but it's cooling the battery bt pcm w 2 concepts air and water, when i tried to setup boundary condition the same as video but i couldnot get the same reslut like the liquid fraction, the line was not rise up, anybody can help me please

Its a good video, What is the differene between meshed wall and shell conduction with or without run_out methods? How to apply these methods in fluent? How to set O_grid mesh for copper tube?

Hi, can you explain how to achieve the formula of heat generation each C rate of battery?

In a similar situation where the mesh is used, and the battery cell is also covered with fluid on the top and bottom, should I add the battery cell sidewalls as part of the Cell Wall and proceed as shown in the video? Or, should I create an additional battery body and add a solid body to the geometry, not just the fluid body?

Sir, could you please explain the results section and show how we can create nice visuals?

Hello doctor, I follow your channel regularly and I have a simple request related to the latest video titled "CFD Simulation of Lithium-ion Battery Cell with Fins in A Rectangular Channel with Heat Generation". Can you please explain how these graphics were obtained? Link for figure drive.google.com/file/d/1xCfXiQhcPlryFKNO1KhWTwy7rH4SOqeU/view?usp=drivesdk

You did not mention how to create Geometry if possible, can you make another video or provide geometry. Thanks