Видео

How can people prevent this happening one day.

MAF sensor could be throwing stabilitrak and traction control.

What r the symptoms when u get that Code. I get that light on my dash bord also I’m about to change the vent solenoid

Are you getting a P0011 with Stablitrak service message?

U sound very humble

How long does it take to remove dash etc and replace the ignition module ?

I just had that issue and changed the starter but it was doing the same thing So we check the wire negative that goes from the battery to the engine block and changed it and thank god that was it .

What symptoms did you have before it went out and couldn’t drive it?. Cause I’m chasing a grinding noise on mine same year. Mines is still drivable but i service stabilatrack with a cel comes on. Thought it was my hub replaced it but still makes that noise

Excuse me, The solution of the problem is change the transfer case? I have this problem also, thanks for the information

I Know The Problem, The GM Dealers Know The Problem But, They Donot Wanna Tell You, All Of You SUED GM Because Everybody Replaced ECM Because Of A Lot OBD Codes But Problem Is Not ECM, It Is A Electric Short Causing To The ECM To Be Malfunction. Amén.

did you reuse the clutches?

Did you get the p0011 and stabilitrak and traction control??

rock auto the best...always ordering parts from there

Man!!!! That didn’t work for me…..I’m going nuts here

Mine doesn’t even do that from the beginning

Has the stabilitrak and traction control and p0011 code come back on ?

Ahhhright

Yeah I’m pulling my motor out doing cam bearings rod bearing main bearing and also taking the motor to a machine shop I’m going all out I need my truck to last for a while just got new lifters I went with melling lifters and also went with comp cam cam shaft and better springs well hopefully everything goes well I’ll post here on RUclips when I pull the motor out and show you the process

How she doing she still running great no traction light again

I thought my dad was crazy when he told me that's what he thinks the problem is since he replaced the battery and the cables to my car. He has lectured me for years and years not to put a ton of crap on my keychain and this is exactly why😮 thank you for your video!

If you change all the stuff and it doesn’t fix it, I know exactly what it is ask me and I’ll tell you I had the same issue changed everyone of these pieces with all GM parts and none of it fixed the pressure issue no it isn’t the camshaft bearings either.

My Stabilitrak and traction control come on but makes p0011code come on with engine light i changed vvt magnet and vvt solenoid/actuator and camshaft position sensor removed engine light and gave it power also did wheel hub both are bad but only can do one for now it removed the light but comes on and off im guessing the other wheel hub and sensor is horrible i can feel it when im braking and driving but with the new one made a huge difference

Does it have to be programmed

Great job

I think my 08 is doing the same today it randomly turned off coming off the highway. I noticed after everytime i change the oil it never does it till its stime for a oil change. Also my stabilitrak and traction control light come on and stay on

What scanner is that

I was having a no start no crank with a 2008 Tahoe I literally been chasing the problem for 7 hours I have not replaced anything something told me to go unplug the battery to reset the ECU but before doing that I hooked up the computer and it came back to p1682 so then again I go unplug the battery I let it sit for 20-25 minutes I go back to plug in the battery and she starts right up I was about to literally spend $145 parts and labor on the ignition switch now it could be the ignition switch no telling but it started right up and I will continue to chase the problem from there if anything else happens

Big thanks for this video, really saved my ass.

Just happened to me on my 1999 Land Rover discovery 2

Cadillac should have provided a oil pressure gauge on the escalade.

I have the same problem, so is the transmission that needs to get replace?

My question is do you have to pull the valve body to be able to pull the reverse drum

Esnesesasio cambiar la trasmision

Mine started shifting hard only in reverse. Its like a bang otherwise everything works good. 180k running good.

Do you still have the air ride hook up

So the issue was the oil pump o ring after all right

How she running no more po11

Talking to much

i just watched Gary. he a bad dude. Im about to give this a shot. my tranny failed just like yours. good job on yours.

How long did it take u to remove the compounder from transmission

Excellent video, thanks for sharing... I have a 62 te, I changed the torque converter and oil pump and now it only moves in reverse when putting drive, it jerks and doesn't move and I have the codes p0871 and p0585, what could it be? thank you so much

I have had issues with my back brakes dragging thanks to the stupid parking brake design and I wonder if this design takes its toll on the reverse gears. Also the van is so heavy, even low tire pressure can damage it! It's good to see that Rock Auto sells the updated compounder drum which should help prevent the reverse issue in the future. My van just hit 140,000 miles and fixing the transmission should make it last even longer! Lots of good tips for do it yourself save yourself money people like me 🙂 Thanks for the video!

Did it stall with the code? Mine warms up slow down idle goes down to 400 rpm then stalls becomes crank no start until it cools off

What did u use the press drill for?

I have the some problem to my truck. Please where are you located I'm from Rockford Illinois

Did you have to do any sort of reprogramming on the tcm when replacing the T case? Mine went out a couple days ago while driving and thought it was the trans that blew but everything is the same as your pt 1 video.

I had the same code and replaced my magnet, vvt solenoid , and camshaft sensor. Soon as I put those parts in I start the vehicle and it takes for ever to start and gave me codes p0340 and p0341 this was an issue I didn’t have before. My previous issues were fixed by watching this video but now I’m stuck and need help figuring out if this new issue is related to the p0011 code ?

Thank you

Melling makes a fork adapter for the oil pickup tube to have equal tension on the tube. I put one in my escalade. Chevy design fail allowing the o-ring to potentially bypass air, and that's not great for the internals.

Hello! What was the mileage of the car? At what mileage is it better to change the chain and pump? Do I have to change the lid to a new one?