Видео

Glad I could help🤙🏼🤙🏼

Awesome! Glad I could help

Yes

Yes, and this piece of plywood was made out of oak

@@FixItFrench Awesome, thank you for the quick response. I'm needing to replace a set of shed doors as well.

@@jcevans16 good luck 👍🏼

I use hard Styrofoam, and then put sheet metal on top of that.they ice lasts all day in there. An easier way to do it is to buy a plastic cooler and build around it. Those plastic coolers come pre-insulated. Hope that helps 👍🏼

@@FixItFrench perfect thank you so much!!

@@Razzles02 glad I could help 🤙🏼🤙🏼

Put the key in the run position and listen for certain sounds that the window is making. If there is a humming sound then your motor is probably bad. If there is a clicking noise, then that’s a sign that the regulator is bad. If he window motor is going bad, sometimes a little hard vibration with a mallet can cause it to work another 3-6 months. Hope this helps 👍🏼

604-180 These actuators are prone to break on this vehicle. It’s one of the biggest problems this vehicle has. If the AC lines are cold, and you’re not getting any cold air, I would say it’s a good possibility that the actuators are not opening the blend doors

Does your faucet have 1 or 2 handles?

You need to turn on the cold and block off the end of the faucet so it forces the water back out through the hose.

It was pretty bad at the beginning. You can clearly see a much better flow. Hope this helps you like it did thousands of other people 👍🏼

Awesome!!! Glad I could help 🫡

Glad I was able to help!

@@FixItFrench you were, I just changed out my regulator last night after leaving that comment. 10mm socket and a plastic pry bar was all I needed. Thanks again.

@@normalhuman9260 awesome! Glad I could help 🤙🏼🤙🏼

You just don’t want the hose to get damaged

Thank you

Thank you ✊🏼✊🏼

Glad I could help 🤙🏼🤙🏼

Yessir! I’m actually recording a recap video of the planner now

Awesome! Glad I could help

✊🏼✊🏼

Awesome! I am glad you got it figured out🤙🏼🤙🏼

Awesome! Glad I could help 👍🏼

Replace window regulater 3:55 3:57

Thanks

The most likely cause in these Buicks is a leaking manifold gasket. If there are no visible leaks, then the gasket is the most likely cause

Absolutely! I’ve had three of these Buick to get over 300,000 miles

This might be my favorite comment! Glad I could help, and welcome to the crew 🤙🏼🤙🏼

Awesome!! Glad I was able to help

Yes when changing new faucets, it’s a good idea to let the water run a few seconds before connecting the hoses. When the water shuts off, it builds up sediment and often times will get into the brand new faucet. Glad you guys were able to get it figure it out 👍🏼👍🏼

Did you recalibrate the actuator as demonstrated I may the end of the video? You should be able to physically hear the actuator’s calibrating. After you hear that, start the vehicle and test the AC and heat again. I hope this helps

That is most likely just a faulty actuator. The actuators in these equinox’s are terrible, especially in the older versions

@@FixItFrench yeah I’d say that did it. And a good shot of freon definitely helped lol. That top screw sure was a bitch though. Thanks for the video!

@@weatley6241 glad you got it working🤙🏼🤙🏼

Awesome! Glad I could help

You don’t have to, but it will be better for your engine. I recommend always changing the filter. Only in emergency situations would I not change the filter

I even tried blocking the coldwater while it was coming out to try to get water to go into the hot one lol. Makes sense it didnt go to the hot water line since it was closed off haha

@@josiahfam well I’m glad it worked for you 🤙🏼

You can do this same process with the cold water as well. 1. Turn off cold water 2. Remove cold water line from the valve 3. Turn on hot water to clean out the hose I hope this helps 🤙🏼🤙🏼

Glad I could help 🤙🏼🤙🏼

I haven’t been down there in awhile, but I believe it’s particleboard down there. I’m not certain though

Gern geschehen! Thank you for watching the video 🤙🏼

Awesome! Glad I was able to help 🤙🏼🤙🏼

Correct

Yeah, I’m really hoping to see some vegetables. This is my first year gardening so I don’t know exactly what to expect

Thanks brother! We’ve got everything planted, and just sprouted some flowers for the outside of it.

@@FixItFrench Nice, I like how it’s gated in too.

😂😂😂 They ain’t touching my garden this year😂

I also made a review for this planer. I love it, it’s become one of my of my favorite tools

Thank you ✊🏼✊🏼

Love to hear it! Have fun with it

I haven’t had any issues with it tipping. I have a video in my RUclips shorts of me riding it across me shop just to show how sturdy is it. If you are afraid of it tipping, I would just change the dimensions a little to make it slightly wider. Hope that helps 👍🏼

Interesting! I’ll look into, thank you for the advice

Thanks brother

Thank you! We are definitely going to enjoy it