Видео

hi Cobracommander. I know it’s a long video but you need to watch all the bits with the tubes in to hear which way round to layout the tubes ( like when I say about the 3 little holes being at the bottom the side etc) I explain in lots of detail how I of the build totally wrong so watch it again and you should see all the problems explained. cheers Paul

@@paulsmodelshed I think my missile tubes were drilled improperly. I previously ran into another spot on the frame that was drilled wrong. All is well, snipping the pegs that weren't fitting seemed to solve it. Knock wood that I didn't misinterpret something. Thanks again for your advice.

I thought my holes were wrong too. that’s why I had to take it apart and redo it. the holes were correct but I had the tubes upside down. watch the vide to see how to align them at 8:32 onwards. Paul

@@paulsmodelshed Thanks. Pretty sure I have it exactly as you do. At 8:46 and 9:03 those pieces would not fit in either orientation for me because on one side the holes were larger and too close together for either piece to fit, but it fits on the other side. I.e. both those pieces have the same pegs (the 3 sided and 1 sided) but on the metal tubes there are different holes on one side from the other. The pieces in step 57 - my metal tubes have different holes on one side (much larger, and closer together) but all the plastic pieces have pegs with the same size/spacing.

You're welcome!

not found them separately yet. Paul

I have moved house and can’t find it. sorry. Paul

Glad you like it!

Thanks

Thanks. 👍🏼

Thankyou

Thanks!

You are more than welcome. Thankyou for your message. Paul

No Zack, I have both Tamiya and HG models and the HG ones are definitely 1:12

​@@paulsmodelshed I guess they are closest to 1:12. The length of the trucks doesn't seem correct for that though.

You are fine to use it on metal joints but I was strongly warned about its bad effects on plastic. Hope you enjoy your build, be extra careful with the connections for the raise and lower and turning wires. Good Luck Paul

Zach, you are more than welcome. Its so nice for someone to say thankyou. It makes every minute worthwhile. Paul

Glad you liked them

|I can imagine. Its expensive everywhere but all we can do is save up and eventually we get there. Hope you, your friends and family are all ok. we have seen the dreadful news from Turkey and Syria. We send our thoughts and support.

Thankyou for your compliment. Its mostly straightforward, but there are one or two tricky bits. its a great build though very expensive!

Well the answer on where to put it is clear. Stick it on the hemmt trailer. leave the bus on the side in the kitchen. I'm sure your wife won't mind leaving the hemmt and trailer etc on the dining table!!!!!!!! I don't go to any clubs being based in rural Worcestershire, there's not much rc action around here. I have every intention of adapting my removable launch tube to fire a missile but I'm waiting for HG to release the promised scale Patriots sometime in the future (I hope). I saw the Estes video and wanted to see the view from the front too! I wonder if he fired it by radio or had a wire running into the tube ?

Just ordered the hg missiles for the 805. damn they were expensive by the time I paid for transport!

@@paulsmodelshed What’s special about them? It may have been cheaper to make your own. Could they have been scratch made? Maybe ally tubing and 3d printed nose cone.

Hello John, I have the same problem and refer momentarily in my HG P805 Build Extras 6 video where I am lifting a missile tub which is about the weight limit of the crane. The extension of the crane factors large into this problem. It will slip on the clutch far more if the hook is further away from the centre of the base. in other words you can mitigate the [problem by raising the arm towards the vertical or retracting the extension. It's a real pain. I did strip down the base and found the nylon pressure clutch and put some washers to tighten it and all it did was bend the enclosure slightly and still allow it to slip. The only way I can think of to solve the problem is to lock the clutch pieces together with glue. Please be advised I have not tried this as I am unsure how much damage would be done to the motor if it struggled with a load, so for the time being I have left it as standard and raised the load high (i.e. almost vertical) to allow for less pivoting force on the end on the base. Hope this helps a bit.

@@paulsmodelshed Thanks for your reply Paul. Did you take any pics of the crane base dismantled by any chance?

@@johnmortimer7782 sorry John I didn’t take any video or photos. I did see that the motor and gearbox weren’t familiar to me so any thought of changing gearing went out of the window too!

mwaaa xxxx

hello

Hi Yves. The problem with towing the 804 or 805 trailers behind a bc8 is the distance of the hitch pin from the trailer bed. On the HG models it is 18cm but on the Crossrc trailer it is about 24cm. So the HG trailer cannot fit into the fifth wheel . I suppose you could modify one or the other, but it would not work as standard. Cheers Paul

@@paulsmodelshed Thanks for the info Paul. I was also wondering how wide the trailer is (so size from one leg to another leg). Can you have a look for me ? Already many thanks. Regards, Yves

sorry Yves only just noticed this. It is 20" (508mm) when the legs are down and 13" (330mm) when the legs are up.

Sorry for the delay Yves, I was away from home. The part no. for the control boxes is TZ-227. I have searched everywhere bu cannot find a source for these so you may have to contact Guangdong Hengguan Technolog Industrial at hengguantoys@hg-rc.com to find these. Paul

manchmal können träume wahr werden

@@paulsmodelshed Jup ich arbeite dran

My pleasure!!

It’s a pleasure.

Thanks Ashley, ok in order then 1. The hole is rough because the floorplan is solid steel and about 1/4 thick and at the time I cut it all I had was a broken hacksaw blade! 2. If you speed up any of the movements of the crane it will reduce the lifting power. This is why it moves so slowly. Unfortunately the arm rotation also has a slipping clutch which means you can only turn with maximum weight on the hook if its near vertical or not extended! 3 What measurements do you want, the size of the hole, the position of the hole or the outside dimensions of the bed?

@@paulsmodelshedthat's genius and I would love to copy that. Can you share insight on how and what material your tarp is made from ? Thank you sir

Hi John, Thanks for your Kind message. The tarp was made using kitchen roll. I placed it on top of the truckbed, oildrums and the pallet and using a thick paintbrush applied 50% white PVA glue and water mix until it was soaked and draped nicely. I made the folds and creases and continued to brush it onto all the edges. I then left it to dry. Because it was only paper glue it stuck very lightly to plastic so I then ran a thin blade between the paper and the truck bed and sprayed it green. then when the coats of paint were dry I carefully pulled on all the edges to loosen it until i could lift it on and off. Others have used toilet roll and baby wipes to get different textures. Watch out for embossed paper if you don't want funny patterns showing on your model. Search RUclips for "Scale model tarpaulin" and there's loads of tutorials. Hope that helps. Paul

@@paulsmodelshed yes sir will do. Thanks so for for the info and inspiration sir

Thankyou. It was an absolute nightmare to cut the base its about 7mm thick and I had to use a hacksaw!

Several people have contacted their supplier and received a replacement, sometimes even free of charge.

@@paulsmodelshed got 2 warranty and 2 more spares on mine. Break easily

It might quieten it a little but I think its mostly down to motor speed and all the gearing. When I disassembled the motor om a leg it had plenty of grease but still noisy as hell.

@@paulsmodelshed OK, thanks for the reply!

It's so good.

Thankfully the price is starting to come down a little now. It's a great kit with a lot of potential, but it's a lot of money!

@@paulsmodelshed Yes I bought the trailer with a great price and deal so I will wait to see about that one.

I bought it on ebay searching for "plastruct". It was part number 90522 catalog number BFS-20 www.ebay.co.uk/itm/153981929373?hash=item23da09c79d:g:QusAAOSwADpa1LDD

I have to agree with you. If I had the money a convoy would be great but I'm not that interested in the Radar. The missiles are far more versatile Paul

@@paulsmodelshed agreed the patriot missile system is way better then the radar.

Ja Lucas , es ist ein wirklich guter Bausatz. Ich habe es genossen, es zu bauen. Paul

Ah...... Well that's the thing, you see this Hemtt has a little secret. Under the tarpaulin and the pallet is a hole. And under the hole is..... a fifth wheel! So all I have to do to convert from a 801 to 802 is take the truck bed off or put it back on. Its just a push fit. However I have seen people buy another truck and buy the fifth wheel seperately and use the axles and the fifth wheel and scratch build together. Hope that answers your question. I'll be doing a video soon showing the 801/802 combination. Paul

Thanks folks, It's Paul though. Dave is my friend who has a facebook account!

Ashley, Thanks so much. It really makes the difference when I know that it's all appreciated. It makes it all the more fun for me.

Danke Ambroziu, deine videos sind super!

Thank you so much. It means a lot when people respond to my videos.

Hallo Hardy, ich habe meine von Aliexpress gekauft. Banggood ist besser zu handhaben und im Moment sind das wirklich die einzigen beiden Möglichkeiten, denke ich. Einfach bei Google nach HGP805 suchen

@@paulsmodelshed Danke Dir für Deine Antwort. Habe den schon bei mir zu Hause. Sieht alles Super aus. Wollte meiner Trailer aber gern umbauen- elektron.- betriebene Abstützung.

Hi Kirk, Two months ago you made 2 comments on "Build part 1" and one question on "build part 2". I answered these questions trying to help you at the time. I asked about what was happening bu you didn't reply to my questions. perhaps you can look at those comments now and we can go from there? Paul

Hello Paul yes my job kept me busy but now I’m retired so I have all the time now to get to my passion ok I may have to get a new Circuit board for the elevation of the tower everything else works fine and I love what you are doing with the kit because the instructions definitely don’t match up and a lot of the parts are duplicated if you know what I mean and you seem to be the only person that has a good understanding of this kit

Thanks, Did you check the M3/M4 wires weren't crossed over on the board. If they were then you'll most likely need a new board.

I think they were but everything else works can I use a different transmitter like fubta

Sure Kirk. But you would need to know how to program the transmitter to mimic the signal that the board is expecting. I would not even try myself as I think it would be a bit of a nightmare. And just changing the RC gear wont repair the board. Is there any sound from the motors when you try to raise or lower the missiles?

Thank you

Gracias Javi. No tienen mucha potencia pero se ven bien.

Thanks Westernsharpie. I really enjoyed making these, never done it before.

@@paulsmodelshed well you did a perfect job. I love these detailed instructional videos because they are so much more helpful than the manual. Nice of you to share. Keep up the good work 🥇

@@westernsharpie wow thanks. I hope to keep going and doing more things like this. Next video will probably feature the 802/801 switching truck.

Yes, it's a fun build and quite an impressive piece when finished

Hi Pete, I got the parts from Aliexpress www.aliexpress.com/item/1005002975729973.html?spm=a2g0o.store_pc_groupList.8148356.7.31b66e3ciXO3MX Please note these cannot lift the trailer. They will drop before release and raise after truck has re-attached.

www.aliexpress.com/item/1005002975729973.html?spm=a2g0o.store_pc_groupList.8148356.7.31b66e3ciXO3MX Please note these cannot lift the trailer. They will drop before release and raise after truck has re-attached.

​@@paulsmodelshedWould you consider selling a "kit" version of this product? Something that basically just bolts on?

I'm still trying to understand what is going on with that slip ring as both elevation motors should be the same, so why one has three wires and the other two I don't know. The extra wire must be a permanent plus or minus connection to cause the missiles to raise up without getting a signal from the transmitter. It's all very strange.

@Paul's model shed the one with two wires connecting to m3 is a power supply to the two motors that control the launcher the one with 4 wires which connecting to m3 takes the power TO the launcher and then to the transmitter. those are the ones i mixed up, so instead of being controlled by the transmitter it had a constant power until it blew up the regulator. at least that's how it appears.....

Ok not sure about the power to the transmitter bit but whatever it is it’s a crazy thing to have to spot those tiny wires when logic dictates that each one would be attached to a single actuator. Hopefully others will see this and not fall into the trap. Thanks Pete.

Oh and the two wire one goes to M4 not M3.

@@paulsmodelshed you see how easy it is to get wrong....but very important you don't....lol

Yes, Amador, I hope to see the yellow ones soon. there are a lot of people waiting for them.

@Paul's model shed yeh they were supposed to be out last month but obviously got delayed....it's a bit annoying they advertise something that's not yet available....grrr!!