Видео

Using heat from the exhaust would improve efficiencies. There is flammable gas in the exhaust gas that could be added to the ratio.

New here , this is wild. Could you power a machine or house from that ?

You can put fluorescent lighting tubes vertically beneath HT lines, with one end in the ground, and have them illuminate quite spectacularly.

I've built 7 different setups en found only thay its hurting the power en efficiency on the engine do to Low fill factor em that is bad for the effective compression ratio. The Geet system was a scam al along. i should have seen this earlier 😅

🟦…From personal experience I've found that an 8-ft fluorescent-bulb will get brighter than a 27-in fluorescent bulb under the same circumstances.

I just hope you're not living near or underneath those power lines

I’ve been following the sand battery idea and yours is a great experiment. We need to try a 4” x 4” box of sand mass and see how long it will hold the heat. Your wire you were using could have been Nichromium wire. It is used for the same purpose idea and is readily available. I’m looking at a galvanized grain storage bin for my sand storage container. Keep up on the science of heat storage you’re going in the right direction.

Hook up a welder to the fence

Can you make a packaged product and export it

Mui buen proyecto

The electric grid owners are trespassing on his property with their electron radiation… therefore he is within the law to keep what they leave

I have used refractory cement mixed with steel fibers consolidated with a vibrating table made from an old van tyre and a cheap bench grinder motor with an offset balance shaft .three years of use and the refractory panells are like new No spalling or degrading .

looks a bit complicated. I use solar motion detecting lights. they run about 10 bucks each and last a couple years. so far.

great information, thankyou. I would like to replicate this in my area as am close to a large radar station. If i can collect enough for 12VDC i can power my ion motor generator. Please could you draw a schematic of the wiring , winds etc. Many many thanks.

Shit me not bro. I lived under some large overheD power lines, the kind that are way up there line 30 feet up. And my kids bith suffex from early onset balding- receding hair line and hair loss. My 27 year old looks like he's a young face 80 year old with bald spots and my 21 year old son has a receding hairline that looks like something you would see on a 60 year old man. Then we seen hus friends that grew up in the same trailer park and the same thing no hair, even his friends sister had a severe hair loss that she fixed with hair plugs.

needa look into telsas one wire light, usign high voltage ,

I have had some ideas that might improve the efficiency and swept area of your design. It would call for you to cap the upper part of the VAWT to enclose your blades. then build a tower based on this video: ruclips.net/video/LteWS7OdaRs/видео.html . If it works with your design you may increase the efficiency based on this video from Veritasium: ruclips.net/video/yCsgoLc_fzI/видео.html . I look forward to future experiments if you decide to include some modifications based on your take of the information presented.

If you get a large block or bolder of white granite and put one of your poles into the granite you'll be surprised how much voltage you get. If I could post pics id gladly send you a diagram. Look at teslas warden cliff tower design, he had the tower connected to granite buried in the earth to increase the resonance

I'm building a large off grid private facility in the mountains of the remote Arizona desert. I've been working on using electrostatic electric ( Natural power of the earth) to power the entire 6000sq foot shop. Looking at your designs your pretty much right on par with the project im working on. About a half mile on the other side of the property is an 80,000 KV massive power line, im wondering if I could increase my voltage by incorporating some of your design in with my electrostatic collection system. Might be fun to try.

***BUILD YOURSELF A LARGE INDUCTION COIL AND YOU'LL BE PUMPING THE VOLTS!***

Rodriguez Angela Johnson Ronald Lee Margaret

there's a hidden very deadly danger, if you have such a setup and a power line comes down and hits or gets even close to that "fence", it will vaporize and arc anything connected at any distance and then some. sure wouldn't want that hitting an electric fence, let alone it being tied to anything anywhere near human inhabited areas.

what is the probability of influencing a lightening strike on your "antenna" -- and should you design some protection into that circuit?

So you noticed your physical proximity to the wire/circuit was having a negative effect -- quasi-grounding field proximity being induced. That should explain the unexpected DIFFERENCE/LOSS you're seeing between 8ga and 30ga wires. True the 30ga wire is higher and thereby closer to the HV lines -- HOWEVER, moreso your 8ga is terminated on insulators that are an INCH away from a grounded metal stake. That grounded stake proximity is huge, just like your body was. The 30ga is insulated on a wooden stake (some 8-inches away from the supporting metal stake) -or- 8X time distances of the interfering grounding field...

This is why you should not live anywhere near power lines. EMF/Cancer.

Have you ever tried getting Telluridic enrrgy directly from the earth? It's on my curious project list, about #432, but an interest.

high tension overhead ....

This phenomena is called induction. The fence is inducing current provided by the magnetic field expansion that is obviously reaching the vicinity of the wire fence. Similar situation to a transformer where one coil is being induced into another ie. primary to secondary.

Nice! :)

Could you use that power to charge a battery or power a light or something?

Impressive. Would be good as crystal radio amplifier :) Thanks!

Cool stuff. What kind of voltages are you getting off your roof top?

👍🏼😉

Great stuff, always interesting. Cheers.

Thank you for sharing. Congratulations, what an amazing innovator you are!

I love watching this channel progress on with experementation. Very interesting

Would love to see a low powered micro controller running off the Electro-smog Energy Converter - passively powered computing

Cool. I've thought about, but can't find any info on a horizontal axis crossflow turbine(s) but strung on a wire between poles or trees.

in the early 80s a family friend who lived near the power plant and its transmission lines showed us how the fluorescent tube lit up just holding it in the air near the lines.. as kids we were amazed as if we were seeing magic! it always stuck in the back of my mind as a reminder that there are things around us that affect us that we can't see.. it was a powerful and inspiring lesson

use sail cloth in a sail frame, steel is fine but harder to make big and more expensive

That is stealing unless they say it is ok

Nice project. Throw a nema 34 stepper motor on there. You can produce decent power at lower rpms.

I've always wanted to try a darwin design wind turbine with a 5 blade horizontal turbine hung upside down in the darwin turbine housing and see what effects you could get.

Nice design how did you figure the layout and spacing on the rim for the extensions?

Happy to see continued interest in wind as an exploitable resource !

I have a similar easement but is for a petroleum line. Every 5 years they come out and cut trees. Technically they could remove my fence and gardens but haven’t

Spinning thing rises up when Spinning fast

Wings that spread when going up and thins when going down against wind but making a duct blowing wind other side, vertical

is this in Montana?

Wow the wind is gentle it can rotate it is amazing I will imitate to make a wind generator thank you for sharing