Видео

Feel for ya. Thanks for sharing. I avoid white like the plague.

Great build 👍🏻

Should of saved your money lol

Hey nice build. Yeah this kit is a bit wibbly wobbly in places like you say. I don't think it's very fast out of the box and it's a bit all over the place so the contest will be tricky. I look forward to seeing how you get on 😁👍👍

Adams playground over 50mph so far but not sure gps is correct so ordered new one

❤👍👏🔥😎👑🤩🏆🤣coool

Looks great.

Fantastic looking beetle.. I love it!

Late to commenting but that looks the business ❤

Hey you've done a lovely job on that 👍👍 Good luck with the contest 😁

Where about’s is this? I didn’t know it existed, near the park?

Great colors!

Where about’s are you based? Looks like Bognor Regis?

Where you buy body?

Great job on the body, those stickers made it pop! Lots of luck on the challenge! 😎👊👍

Looks awesome. Wishing you great runs and lots of fun 👍

Good looking body, now let's get it going fast! :)

It looks fantastic!! I'm happy to see you I this. Best of luck!!!

Looks awesome mate!

The stickers makes the colours look great!

looks great! best of luck

Nice paint job, loving the colour scheme you got going on there. I'm struggling with the rain up here can't get any painting done yet and there's not a lot of spares for this chassis in Wheelspin Models, all the main bits are sold out and it's only going to get worse. Got the car sort of built waiting for the bearings to come soon I hope. Good luck with the SRC, it's going to be a fun one for sure.😊😊😊

The body looks well!

All you had to do was recalibrate the esc 🤦🏻‍♂️

Lovely to see you back in the 2024 SRC!

The three m red things you saw our double sided sticky tape.

Have you seen the hornet Evo?Are you going to get one?

Good Luck!

Hey, difficult to comment on, without being in front of the car. But you mentioned moving the timing of the motor, that will impact top speed without a doubt. Also you mention having to reverse the throttle using your transmitter, you could leave the transmitter setting as standard and simply switch the wires from the motor to the ESC. Check your transmitter for the end point limit adjustment, also your ESC, you might need to go through the throttle calibration sequence, hope to see some improvements for you 😊😊best wishes 😊

Hi Ian. looking forward to see what you do with this car, best of luck out there on the speed runs! 😎🏁👍

Awesome video! Hopefully my kit will be here this week! Good luck!🤜🤛

Looks like Fil has his work cut out this year with the amount of channels already joining in. See you near the bottom of the leader board 🤣

Great stuff, buddy, I just subscribed so I won't miss your speedrun! I saw you posted to the group, but this was RUclips suggesting I watch the video this time. Have fun with the challenge, I'm in brushed as well, perhaps we can battle for last, ha ha! Or probably lower middle is where I will end... I just counted, I have 4 RC car challenges going this year, so I got plenty, ha ha... But as you say, they are so tempting...

Nice!

Nice great to see all the entries..

Great to see you again in the Challenge. Have fun and get good results 🤩

Glad you entered and Great Luck!

Nice to you decided to hoin in the fun 😁 i still need to save up for the kit. Hopefully i’ll be running later next month 🤞

Great! It's nice that you're joining in.

Great 👍 I'll see you in the brushed category 😉

Awesome! Good luck mate!. Honestly, lipos are not as bad as you may think. There are warehouses and hobby shops full of them and none of them are going up in smoke. Like any battery if you keep it in good condition it will be fine👍🏼

Very nice!!! I made my first run yesterday after building it. It was a fun little car! Very happy to see you in this one!

I have the Spektrum DX5 Rugged. Though I think the Radiomaster MT12 has cheaper recivers and you can use the 4 in 1 with a ELRS module. Then you can do mong range with new recivers and also use a bunch of different on recivers and come with a case that's also nice. I picked up a hard deck for 6 bucks AUD in Tokyo couldn't go past that bargain.

I just picked up a 63T and a bunch of different sized motor pinions from Super Rajikon. I am not sure about that issue unless you swapped the motor wires. More of a nitro guy a bit new to the electric scene.

Your problems started when you tried to adjust your motor, that’s the issue you needed to go back to instead of changing everything else, sorry if that’s not very helpful, it’s just a thought. Best of luck, I’m sure you will get there👍

Too bad about your problems 😢 But sounds like we will have another Overhaulin' episode😊

Ok, lets start with the basics, most (95%) of RC motors spin in a counter (anti) clockwise rotation. Hook everything up as it should be, use a rubber bands, zip-ties, cable ties or something to attach the motor a pair of pliers (adjustable wrench) handle or a motor stand if you have one. a long piece of tape around the motor shaft will tell you if its spinning the wrong way, again, that's if all is hook up (attached), if it's spinning clockwise, remover the brush springs, pull the brushes out a little, loosen the endbell screws (no need to take them out) and try to rotate the endbell, if it don't move, unscrew the screws another half turn, repeat this till it rotates, rotate the endbell 180 degrees and set to zero timing (you can play with that later). Sometimes pushing on the endbell screws is needed to push the lock ring down. Don't go over crazy tightening the endbell screws, just snug them up then just a nip up, go too nuts here will strip the lock ring or even bend it, I seen both in used motors I bought. A piece of notebook (lined) paper between the pinion and spur is a good start for the gear mesh, I like to use a piece of printer paper, It seems to work for me. Now, about the radio, Is there a way to factory reset it? Test it with other gear (not in a running model) and see if the problem persists, if not great, if so, might be a radio system problem.. I hope this helps and I do hope you get things sorted out..

Did you repair the shaft on that better motor atl?

It is so difficult to diagnose your issue, but Im sitting here struggling with it just the same. Other than an esc issue at this point, I have no clue. If it is a 1060 you may or not hit the limit of current that will pass through it. Best of luck.

Can't hear what you are saying...