Видео

hydraulic brake kit ? that seat triggers my ocd . very nice build . wire management a key , good job

De-pin and cut the wires so you won't need to hide really long cables, the bolts you used on bracket you made for the rear brakes are almost touching the rotor, if the frame flexes you're gonna have a bad time. I know this is an old video but I sincerely hope you improved since then

2:50 why'd you put threadlocker like that, just coat the bolts bruh

I want to do this to my bike. I have a giant that's almost the exact same model and I really think it would be awesome to do this.

Did you have 29 inch wheels or 27.5 do you think it makes a difference on top speed ?

id want to see this with the usual dirt, water and mud my bike goes through every ride 🙃

Great video. These things are great ,I just picked one up for $100 after wanting a Prusa for ever. I did put a video up on channel

Whats the size of the geometry of the triangle, i need to find a frame where i can fit a 14 inch by 4 inch battery

What was the total cost of everything besides the 3d printed stuff I built a sick mountain bike and I would love to make it motorized

I like your creativity.I prepared to follow you.

Aaron thanks for this video. I watch lots of your videos. Please can you help me this: I have similar set up like yours. brushless hub motor of 1,500 watts 48v, with controller of 60A peak. But when climbing hills the bike goes off. I guess the controller shuts off. So I don't know could it be the battery or the controller? Your opinion or if any experience on this please. Thanks

How much All this?

Will a triangle battery fit in a. M/L trek frame

such high quality content, i cant believe my eyes when i see you only have 1k > subscribers. May Jesus be with u

Your Viedo is very beautiful but your Viedo is not correct Tittle, Viedo tag and Viedo SEO are not done. Views, subcribe is not increasing because of this and not uploaded properly. If you don't mind, I can do these things for you?

Amazing idea and execution, was looking at doing something similar myself this is great to see. Thank you!!!

This is sick! For v2 using 80/20 extrusion to build the frame might be a good option, it’s easy to work with and super solid. It is a lil pricey though

Should u trust aliexpress and are they good?

Why you suddenly start doing fittings on the brake that is unnessacery

What frame size

You can put the cassette freehub body in a oven for about 10 minutes and the bearings can be pressed in by hand. Clean off any grease first though. Makes it super easy. Put the bearings in the freezer first. Almost forgot about that.

Do you know any cheaper and easy kits for hybrid bikes?

What bike is that I know it’s the trek marlin 7 bait what gen???????

Awesome! But you wouldn't have believed me... I picked up a mk2 recently off local for free. All I did was dust it off and moved the pinda probe around and it works flawlessly. Looking forward on more videos for upgrades.

H same one I getting

💯 Upgrade is Avenue Suspension Trucks on the Front and rear on my Exway,😎

I was able to build mine and blast fire over 8 ft

1:43 no no no !!! you should not remove the slides like that, there is a huge risk of losing balls, it is not for nothing that the manufacturers place plastics of the same shape as the slides...

Hello, great build, im doing a 48v 1000w conversion, do I need to fit a fuse between the battery and controller ? Any advice would be appreciated 👍

Is this ilegal?

Amazing video! Very cool. So all in all, how much did this cost you?

Cześć, fajny film. Też buduje Vorona 2.4 R2 na moim polskim kanale. Jeśli masz ochotę zerknij.

This video looks like it should be from a subscriber with atleast 100k subs. Very nice, clean and to the point work with some good editing.

How does it compare to the SOVOL SV08?

Ultra hardcore DIY with metal works and a bit of engineering. Props.

Tools from 1,5mm to 3mm in 5 mm increments? How does that work

I eat those side panels as crackers

the 2.4 DOES uses a Z endstop, they just call it Z probe. the inductive probe (like klicky with a basic confic) is just used to level the Gantry and to create a bed mesh. you still always home Z on the z-Probe and set your nozzle offset on a reference point on the bed. you can get around it, but i would consider this advanced.

Very well done mate💯 ! - i can just agree its the best printer to get ... but also a dangerous rabbit hole 😅 Klicky and sexbolt is absolutely the best combination for z offset calibration... i recommend a nozzle brush too... due to inconsistencies i already ripped my PEI sheet 💀 Next step is to give it some speed... and at least go stealth burner ... maybe with Canbus ? for people that get themselves a new kit... i can recommend MagicPhoenix out of my own experience, lots of customisation...and it comes with Stealthburner and Canbus

This video is amazing!

i like voron tap way more than clicky

Read about canbus and Tap click - you will save time with cables. You get a thumbs up from me for encouragement!

Step 1: Buy Sovol SV08

what's with the stack of cash on 1:11?, hahhahhaahah

Cool Video. Can't help but notice thought that the Formbot Kit I am looking at purchasing is already quite changed to the one you built. It is advertised on the Website with Manta M8P and Can Daughter boards EBB SB2209 CAN /EBB SB00000 CAN and a VORON TAP Variation. So might be great if you still have it to post the BOM your kit came as a comment perhaps so that your tips and tricks are easier to apply to newer kits.

your bike is a bit small for you. or you need to put your seat higher.

Ive used THE cheapest tubes like 2 euros a piece and that shit was fine😂😂 maybe you need a bit smaller size

Disc brakes are heavier than rim brakes and may be over rated. You definitely need good brakes for an e-bike. I have been doing some research and quality rim brakes may be a better solution for a lot of ebike conversions based on frames without disc brake mounts and your conversion proves there may be other problems with conversions as well! Off road pedal dirt bikers and road bikers, prefer quality rim brakes, besides being lighter, they really work well! Rim brakes vary in quality a lot. Good ones cost $$$.

Hmm, interesting. I was wondering if it was even possible to do a conversion on a dual suspension. I've got a 2004ish Mongoose Teocali comp I wanna do a conversion on but the frame and suspension setup is a bit different to this bike so I need to a bit more research and go see the guys at the local bike shops to see what they think the best setup would be. 👍🙂

You need room for larger bitcoin . $100000 won’t work