Видео

Ah man I couldn’t believe it when you got another oil leak, so glad for you that finnnnaaalllyyy it’s done🤞🏼. Glad you’re back and well, my 123 is still on the shelf waiting, so looking forward to that one and to see what goodies you have for your motor👍🏼

Pleased to see you back with a new video Jamie. The oil cooler differences was some new info for me, I took a screenshot for future reference. You have the worst luck with oil leaks but you got to the bottom of it in the end. Cheers.

Nice job Jamie! Sounds excellent. Good to see you back, its been awhile.

So what did you install in front of the resistor?

I have to hand it to you. I have watched 3 videos and you are the only person that mentioned that the two top bolts are actually bolts and can spin. Especially the one behind the starter. Most say there are studs.👍

Would those gaskets you added in the end as spacers help to eliminate a 'diff whine'?

Seriously?..crow foot spanner set in metric is what I use without dismantling the carb in situ,fuel line ? I have fitted bsp to jic m/m fittings and run petrochemical hose with crimped ends..the looks good with Petrochemical hose in FRAS sheath ..fittings in carb dress it up nice and the entire use of hydraulic hose in my engine bay for full flow system is built for longvity and reliability ..

Hi Jamie , Fantastic videos you make . Just bought our first VW . Got a 69 Beetle and we want the same ride height as you just did . Looks Awesome ! So the beam you welded the adjusters on are stock width ? We are looking to buy an EMPI stock front beam with the disc brakes already installed . Called Beam in Box . Our car has the 165 tires that are new . So just by the adjusters we can Lower like yours without a drop axle ? also the tires wont stick out past the fender with disc brakes on it ? This is all new to us . Worked on Chevy's all my life so this is way new to us . Thanks and just by watching your video's we can do it .

Fantastic video . Just bought my first VW bug 1969

Por la forma de explicar despierta el interes a quien no somos mecanicos. GRACIAS DE NUEVO

A new Beetle owner here, got mine cheap as previous owner stripped the threads on a cylinder and the car was left to rot. This video was very helpfull, I didn’t even know such tool existed. So I went to Biltema and bought it. Thank you very much! 😊 Even tho, I did it without pulling the motor out so it was very hard to work on it as there is not much space and you can’t see the hole. I had to buy threaded pins M12X1.5 and M14X1.5 which I had to run through first because this tool just didn’t for some reason bite in and start to make the threads first without it PS: Do you live in Finland?

Take a look at the reinforcing plates for the rear differential mounting areas as they had a tendency to crack with flexing. It's an easy fix when the chassis is bare.

I think you are very lucky and you won't have to do this - TR6 - Rotten Frame Repair - part1 - Trailing Arm Support

Where did you get those spindles? I'm trying to install the same empi disc kit in My 69 bug but, i just notice the inner bearing won't fit since the spindle is bigger (variable diameter)

Muy clara la forma de explicar Mister. saludos

If you think in Finland the tax for import an european car it's too much... Then you must don't know what we pay to import to Portugal... Just crazy crazy values... Great video btw!

I have almost the same car but with nimbus grey leather. Had it 3 years and still absolutely love it and have no plans to sell it! Such a beautiful design inside and out and to drive with the 6 speed manual box is sublime. More than enough grunt, handles well and suprisingly economical on a run - high 30 to 40 mpg. Big boot and glorious straight 6 lump. Whats not to like?!

Always lovely to see Dusty boy, hope he enjoyed his walk 🐶

Great little cars, my friend has an si coupe in a similar colour scheme and i have an early roadster. Brilliant road trip cars, suprisingly comfortable and sound glorious when you push themon a bit

If they are wired in parallel, how will you know if there is a failure?

It's worth checking the pressure from the rebuilt pump if you have access to an inline gauge and comparing it to what your carb is expecting. If the pressure is too high then fuel can push past the inlet valve on the carb - not such a problem with the engine running and a vacuum in the inlet manifold. However, after the engine is shut down the excess can run into the carb throat and leak out of the throttle spindle and blanking plug at the base of the carb and drip onto a hot engine. Eeek. The general internet advice is to stack more gaskets under the pump and effectively reduce the pushrod stroke. Rob & Dave's air-cooled advice pages disagree with this approach. They point to overly long and/or strong main pump diaphragm springs causing excess fuel pressure. You should be OK with Paruzzi kit but it's still worth checking for safety. I've been faffing with carbs and pumps for the last 2 days after installing a rebuilt pump from a respected source which I've had to back out due to the worrying drips after shutting the engine down. Good luck with the KG !

Same problem. Can i ask what is the insert size?

Well hello you great big tall stack of freaking sunshine. 😊 A new video! Love to see it.

Excellent and informative video as usual, thanks mate

Nice one Jamie, I’ve never seen or done that before,very informative. Looking forward to seeing that 123 timed, I’ll attempt mine after that😂

There’s some great replies there Jamie, hope you get it sorted soon, watching with interest 👍🏼

Nice car man. Repack the box with grease, not oil. Asjust the screw just until it snugs then lock it down.

Bought myself one 2 months ago. Automatic transmission though but I can not complain. Iteresting part is it's also 2007 and it was imported from Finland in 2018.

If you have a leak from the oil cooler seals the problem is probably not with the size of your oil pump. It's because of the way the cooler was installed and not seated properly, or one or both of your oil pressure relief valves are gunked up or stuck and not functioning correctly. On older cases there is only one pressure relief valve and we would use later model valves and springs to increase oil pressure at idle. You've got to make sure that the galleries where the relief valve plungers live are spotlessly clean or you'll have issues with them sticking. The other thing is what viscosity oil are you using? Back when the VWs were still being sold the recommendation was straight 30 weight oil for most climates, 20 or 10 weight for extreme cold or harsh winters, and 40 or 50 weight for extreme heat in summer. Now I believe that depending on climate that modern 10w-40 or 20w-50 is recommended. When I was younger I lived in South Florida where maintaining adequate oil pressure in the hot climate was always a problem with air cooled VWs regardless of engine displacement. I rebuilt dozens of VW engines and the first thing we would do was install a higher volume oil pump and later style relief valve plungers and springs, and convert to a dog house oil cooler like you did. This made them run cooler with better oil pressure when hot. If the pressure relief valves are doing their job correctly the larger oil pump will flow more volume of oil per minute, but the pressure won't be any higher at speed than with a smaller pump. The improvement is at idle and slow speeds. That's because the relief valves will send the access pressure back to the sump. If the spring(s) are too stiff that could also make the pressure too high. Make sure you have the correct plunger and spring in the correct place. They are different and mixing them up can be a problem too. When installing the oil cooler you have to make sure that the mounting surfaces of the case and the cooler are perfectly clean and smooth. Use a mild solvent for cleaning and a fine grit sand paper to smooth up the surfaces. Then use the Permatex Aviation Sealant that's designed for air cooled engines. Finally, check your oil pressure with a gauge, like you did, but hot, like after a long drive in traffic. As I said, if it's too high it's most likely that one or both of the two oil pressure relief valves are stuck or sticking. Too low then the springs are incorrect.

take the oil cooler and adaptor off, remove the studs and sand it on a glass with 400 grit like an intake surface, also remove the little stud from where it sits on the block and sand that pad down too with a block... check the edges deburr anything that looks like it can get hung up or make a gap; i put aviation permatex on the seals before installing them and use nylocs with flat washers to hold the adaptor/cooler down too;

There's an article in VW Trends mag summer 2024 that explains how to set up the oil pump. Enjoy the day Peace ✌

NPT, Also known as American National Pipe Tapered Thread. 👍

Is it still leaking oil from the oil cooler?

I've never seen that kind of fuel filter on a series. It looks a lot more effective than the inline filter I have.

Great video

Beautiful engine. Nice video

Did you have to pull the bearings out of the beam? Do you leave the insert that you knock out of the center inside the beam?

I have this problem on my VW type 4 engine. I might give this a try once I have the engine pulled

I finally bought an E86 3.0si manual a month ago, I absolutely love it! Adorable body shape IMO and feels like a proper drivers car, You climb into it and you sit so low! The N52 engine is a peach and sounds gorgeous and the ZF 6 speed box is a joy to use, The E86 was only produced for 2 years and people like me are waking up and smelling the coffee hence me getting one as prices IMO are not going to get any lower and they will soon be on the up! Mines a keeper, I am not ever getting rid unless drastic circumstances force me to do it, Also liked and subbed 👍

Nice video but one important step is missing and that is to bring the diaphragm on the correct tension by using a special tool known as VW328d.

I lost one of those ball bearings an i took apart a 3/8 craftsman ratchet an used the bearing from it .😂

Great video, can you tell me what size the copper washers are?

This has been really helpful thanks. I made the same mistake with the fuel filter and now have to bleed the whole system. Out of interest how long did it take to prime the whole system. I’ve been trying for about 15 minutes and gave up. Any help would be great.

You picked the right car, I've had my 2007 3.0si in ruby black over parchment leather/piano black interior for a few years now and love it. Easy to work on, looks fabulous and a great drive. Great travel blog guys!

Can you do this to raise.

This has been such a helpful video for me. Thank you!

Hi, which kid did you buy, the only one I can find by Empi has dropped spindles for a 1954 beetle.

Can you tell me what company have you used to arrange those plates? Thanks

Thanks a lot for this: I am about to do the same on an old resto / fixer-upper Here on KZN South Coast. EP 90 in Diffs and swivels too. Ill take a look at your other vids as well. Cheers.

Great car! No turbo problems, manual transmission, and hatchback makes sports car useable. And old enough to not have all the computer issues.The video was very interesting glimpse into a great journey.