![HVAC MADE EASY](/img/default-banner.jpg)
- Видео 23
- Просмотров 132 110
HVAC MADE EASY
США
Добавлен 14 сен 2021
This channel is dedicated to the HVAC/R industry, especially for those that are new to the Trade. This channel aims to educate and inform technicians about the every-day experiences that service and maintenance techs may encounter on a daily basis. Welcome to HVAC MADE EASY, this is "Where Breeze Comes Through".
Видео
How to Unlock Honeywell VisionPro 8000 Thermostat
Просмотров 9 тыс.Год назад
#thermostats #honeywell #hvac
Air Conditioner Cleaning Using Nu-Calgon No Rinse Evaporator Coil Cleaner #hvac
Просмотров 15 тыс.Год назад
#evaporator #ac Music: Blue window Musician: Jeff Kaale
HOW TO PURGE YOUR REFRIGERANT GAUGES #freon #refrigerant#r410a#r22
Просмотров 4292 года назад
Refrigerant gauges purging procedure
Milwaukee M18 vacuum not working? #milwaukee#milwaukeetools
Просмотров 27 тыс.2 года назад
My go back to battery vacuum for clearing drain lines stopped working. This is my second failed Milwaukee vacuum in the past 6 months that stopped working for no reason. #milwaukeetools #milwaukeem18 #vacuum #drain
KLEIN TOOLS 11 in 1 SCREWDRIVER HACK #kleintools#screwdriver #hvac
Просмотров 3262 года назад
Klein tools 11 in 1 screwdriver hvac hack
Carrier Core Valve Replacement | #carrier#hvac#ac
Просмотров 1,2 тыс.2 года назад
Carrier Core Valve Replacement | #carrier#hvac#ac
Hard Start Kit Exploded | #hvac #ac
Просмотров 1,8 тыс.2 года назад
Hard Start Kit Exploded | #hvac #ac
How to adjust belt tension on a blower motor | #hvac#ac
Просмотров 1,2 тыс.2 года назад
How to adjust belt tension on a blower motor | #hvac#ac
Ty
Thank you for this tutorial! I opened mine up and saw the red wire at the solder point on the board was disconnected from burning up, right at the solder😂. I just cut that extra red wire coming from the switch and reused because I didn't have any spare connecters. Works like a charm! 🙏
Thank you it worked great
Exactly what I needed, much appreciated 👍
What’s the fix for the board….is there a fuse or something? What does the board do? Do we need a circuit breaker now?
Great video keep them coming love the content🫡
Great video keep them coming love the content🫡
Funny you used Dewalt tools to repair s milwaukee tool. Good video
Samsung is junk, that's the problem
good job spraying inside to outside
Fans look like they’re spinning backwards
I've had three go out. One went out on the second time I used it.
Hi. How do you change the time?
What do you mean by stage 1 and stage 2 ?
The circuit board is some kind of motor protection.(I think) You can temporarty jumped but not permanently jumped.
Can you use it on a mini sllit
Yes you can
Thank you
You're welcome
Thanks man!
No problem!
great video mate thanks from Brisbane Australia
You’re welcome
Hi, after unlocking the thermostat and programming the temperature how do I lock it back? Please advise.
I’ll make a video.
Hi, do you have a video on how to lock back after unlock the unit?
Great video! Followed your instructions step-by-step and now my vacuum is working again. Thank you so much!
I will hack my vacuum. Thanks mate
What is the purpose of the circuit board if you can just bypass it
Quick fix while in a pinch. It drains your batteries power very fast !!
Thank you. Worked perfectly
You’re welcome
Super Thank You!
Man nice video! Super thorough and clear troubleshooting. Going to save this video for when I have time to take my vacuum apart. Thanks
Hey, whatever it takes to get the job done . Nice 👍
You got that right!
Thankyou.
You're welcome
Very helpful. Thank you
Glad it was helpful!
Nice job brother
Thanks
Youda man
Love the lesson but it’s $99 just exchange it !!
Mine goes out every 3 months and I'm too busy to keep sending them in to milwaukee. They even pay for the shipping when I get them warrantied. I just don't have time or patience for my vacuum always being down.
I think this is known issue to Milwaukee but it costs them very little to manage as the trouble it causes the customer to have it fixed causes very little actual warranty work for them.@@richardpowell2416
Did this turn out to be a long term fix??
It’s still running and I use it daily.
How long should you take to turn on the air conditioner afterward?
I usually wait 10 minutes but it really doesn’t matter since it’s a safe product to use.
This my fav vac, but watch your filter gasket b/c it’s not glued in so it’s prone to falling out which allows junk past filter & into motor which quickly trashes it! Mine works intermittently & I think it’s the overload protection circuit. Fingers crossed it isn’t over 5 yrs old so Milw. will fix it for free under warranty.
I love this vacuum except for when I need to remove the hose, it can be very difficult.
Do you do this before it gets nasty or after
Always clean the drain pan first and this will maintain it.
Hello, thanks for the good video. Could you or anyone point me to a direction where the problem might be when the compressor turns on and shuts off every 8-10 seconds even with the new ptc/ start up relay replacement, any help will be greatly appreciated.
Check your condenser fan
Does this harm plastic?
No it shouldn’t
How are you getting at the evaporator? Top down, bottom up ? Did it improve the cooling?
I cleaned both sides after removing the door. And yes it improved the cooling. A dirty coil is like having a clogged air filter.
@@hvacmadeeasy1788 what about under the coil inside thats where it gets dirty
I thought I would get a suggestion to a "true" fix. This mod would likely kill your batteries, and you have zero protection against short circuits. Fire hazard likely. I won't do this to my machine. Do this at your own risk guys!!
There is no true fix since this model is discontinued. Just add a in line fuse if you’re concerned or just upgrade to the newer models. Thanks for watching.
Someone who can do electronics can do a true fix or at least a much safer one.
They do sell replacement chips for this device now. I may consider trying that route. 🤷
thanks man mine has the same issue and works just fine with the bypass, i just made a spade bypass so I didn't have to cut the factory wiring , seems that card is almost a planned failure feature by Milwawkee tools since mine is only a year old.
Good hydrocleaning of coil thats the best way to clean coils. I would like to know how much hose did you use to get to RTU if the hose bib is on ground level that is a lot of work your hard work is appreciated. it should be a code requirement to install hose bibs on roof tops, in Texas it is a option but not a requirement so it is hard work not all techs will do this.
It’s definitely challenging when there is no water source close by. I used 200ft of hose.
Thank you so much
You're most welcome
Thank you
Note to self.. Check the plug first... Amazing video by the way and I'm very appreciative.
Yes sometimes it’s the small things. Thanks for watching.
Great troubleshooting! I believe the circuit board is what helps ensure you don’t discharge the battery to far and ruin it, no? If so, are you just making sure you don’t run the batter past 1 bar on the power meter or something?
This is NOT "great troubleshooting" It's the easiest way to solve things: bypass everything. I wouldn't do this, it's a fire hazard. The moror runs now, but it isn't fixed, just hacked, in a bad way.
Is it good to be used on car's evaporator?
Don’t see why not
U da man!
I try. Thanks for viewing.