Видео

How would you create one for something that includes latches and PCTs?

Hello I'm new to electronics so can some one please tell my magnet type alternators in cars would an transformer reduction work to 220v ? I mean can the stator leads 3phase by used to connect to an transformer 3phase to 2phase transformer I'm worried about high frequency I wanted to use external indisti type bridge rectifiers so I'm worried about over loading the stator leads inside the alternator just to run small projects .Preciseli I'm just looking at independent ignition system for an 4 cilinder engine with out baterry problems Basicali. So Hoppe some one did similar project in the past. I also want to use that magnet type alternator for back up in case I need inverter to run small machines or light bulbs when power is cutt off. So Hoppe for some sugestions ? I heard an solar panel regulator could by used so I'm not Shure if that would work or not .I'm mostli concerned about stator leads,over drag Hoppe to not brake pulley to engine connection and would avoid engine lagg from over load .

What is the difference between TD and TMS

Thank you for the video! I just want to know why you calculate the pickup for 51 prot as 1.25 of FLA? Which document describes this?

Thanks for an awesome explanation

great video!!! I like to learn more about motor protection relay and power quality calculation

Why do we take 180% of the fault current on the low-side and reflect it to the high-side for 50P? It seems like we're taking extra steps. Couldn't we just take 180% of the maximum high-side fault current based on the transformer size?

Undervoltage setting for MV ?

Phenomenal video. Great explanation.

Where is this slop and settings O87p comes from? Please answer

Friend need this new version etap 22 please. Its possible?

Friend need this new version etap 22 please. Its possible?

Friend need this new version etap 22 please. Its possible?

Please Create a video for substation Cap control

Could you explain or make a video on open phase faults and sequence components. I have a very hard time finding material on when a phase opens but isn't connected to ground or another phase. If this happens, I'm curious on the symmetrical components and what they look like.

Just now i noticed my ETAP 16 is malfunctioning. For protection coordination, whatever values i enter in the differential relay properties box, vanishes once i press OK button. This happens for CT ratings too. When i tried to disable overcurrent protection, the same happened. Unable to set breakers to open. Everything works first. When i reopen the properties box, nothing is there. Everything is in the default value. And so breakers are not opening. What goes wrong.?

Technically manual book of this please

I’m a Distribution Engineer and wanted to advance my Protection Coordination skillsets and this video helped me out a lot with Relay programming ! Great video 🔥

can i have three single phase transformers in place of a single 3 phase transformer.?

youtube.com/@myenergyprojects?si=BVtbeFARuwtDCxn2 please refere for all basics and knowledge information . Hi sorry for posting my channel link

youtube.com/@myenergyprojects?si=BVtbeFARuwtDCxn2 please refere for all basics and knowledge information . Hi sorry for posting my channel link

youtube.com/@myenergyprojects?si=BVtbeFARuwtDCxn2 please refere for all basics and knowledge information . Hi sorry for posting my channel link

How to model relays that are not in the library?

Thanks Sir

Thank you so much. Your Video is Gold❤

I have a three phase CT’d service. The meter is showing reverse current. I swapped the polarity and it still shows reverse current. All of my kWh are showing received. What could be my problem?

Great! do you know where i can find equation for IAC and CO electromechanical relays? please do a new video including electromechanical relays

Is 150% common for pick up current? I am used to seeing 125% on low voltage.

Please make another video and tell about differential relay program with FBD....!

Nice video, its help me a lot to learn etap, thank you sir 😂

Incredible

A TRUE LEGEND. 10/10 INFO

Very nice

Appreciate you for this

Nice explaination dear

I really appreciate your work. How can I simulate transformer REF protection in ETAP?

I am interested in your online courses. Please share the details.

Thanks

Excellent and very helpful video, Thanks!

Great video! It was very helpful.

Hello mate, do you know any reason why SEL uses different algorithms of SLP1-SLP2 for 487E and 787 for example. In former, SLP2 begins from 0;0 origin, while for latter SLP2 is shifted to the right. Cheers

Like

Great presentation. Can you do a video on reliability analysis using eta?

thanks for the video if am to ask how, if am having a transformer which is connected in Delta at the primary winding and star at the secondary is it ok for me to connect the primary ct in star at the primary and Delta and the secondary to avoid the current phase shift thank you

JLAING WATCHING FROM WEST NASSAU

excelente

that was very helpful thanks!

why were current transformes used before CB. should not that used after circuit breaker

Hi, is better to use 5A or 1A secondary core ? for 6CTs and 3 core balance CTs solution.

Excellent video on youtube about this topic. This channel seems underrated.