Видео

I fixed my lawn mower using your video! Your lawn mower was the closest to ours; plastic carburetor and very similar. Symptoms? Would not start and priming had no effect. This mower sat for multiple year periods with E10 gasoline drying out multiple times. Just like you said at 5:18, "if there's a hole spray through it." In my case, most of the holes didn't appear blocked, other than one of the carb ports that the plastic emulsion tube seals into (that pressed in white piece you removed). The one with the black o-ring, that hole in the carb itself seemed blocked or at least restricted. Put as much carb can spray pressure against it. That finally allowed the mower to start, but it would stall unless I pumped the choke. Ran it at high revs (about 10 minutes) by clamping (I know don't do that) the grounding stall lever on the handle so I could repeatedly press the red prime bulb. Dumped the old years-old E10 gasoline back into the gas container with lots of fresh new E10 gasoline. Refilled the mower tank to 1/4 full. Started it by pumping the prime bulb, but letting it almost stall this time. There must be a lot of negative vacuum from the engine as it stalls, because I could sense with each successive near-stall that it was clearing up, able to run on its own just fractions of a second longer with each near-stall. The ethanol must have been getting through one of the plugged orifices and doing what solvents do, dissolve the gummed up hydrocarbon olefins inside the carburetor. I kept letting it almost stall a few more times and voila, it ran on its own!!! A can a carb cleaner (mostly unused), your video, and a little patience. Thank you for this great video!! Success! Just need to let my family know that if they want to keep the mower running tip-top, they need to use it regularly. So obvious!

This video is RUclips at its best. Thank you so much for posting it. I followed it step by step and got right to mowing.

What about showing people how to clean the jet holes correctly. Spraying choke cleaner won't help.

Good video👍👍 I just got a Shakespeare Universal trimmer Head and It came wth 20 Nuts an Bolts 🫨 I have a Left hand threaded Shaft on my Homelite and only one of these Nuts fit. Unreal an frustrating searching on Amazon for a new Head when they dont specify if its Left or Right headed thread in the discription. Anyway great video Thanks I smashed the like button when you said Sanity and Whatever the F*ck this is 😂👍

Just bought mine it stopped running after 30 mins of use.

What is that fuel extraction tool???

So someone would steal my friend's 5 gallon gas from his can that he left up at his cabin every weekend.So one weekend he decided to fix him and fill it with water.Maybe this is what happened..haha

I have a Kohler 21 horsepower and it won't stay running unless you keep the choke on and it backfires out the exhaust and it gets hot real quick what could cause that

Came here trying to fix mine cuz it's not turning over at all and noticed your forearm piece, praise the sun ☀️🙌🏻 I must be on the right path

Awesome video, brotha! 🤙🤙

Did Harbor Freight discontinue the item? Unable to locate it on their site.

Provide a fuel shut off and change the oil.

With tats like that he probably did it himself

eh, some fine grit and spark plug cleaner does the same thing. or just buy a new spark plug. not a bank breaker

Clean oil = beer.

Mine working 20-30 sec ant turn off by itself

are you kidding with this video? i am sea sick and need to puke

this saved me SO MUCH heartache and trouble. THANK YOU!

Turn off the feel

Gotta keep that fuel turned off when ur done too. It’ll pit ur carburetor.

Oil in carburetor 😮😮

You have an annoying clank noise as you move

I use stabilizer and mostly can't tell difference, I do also treat with carb cleaner

To much oil unless it was stored in the wrong side causing the oil to get in the wrong spot

Great video very helpful. Thank yiu. Suggestion. Better still photo of aligned reassembled carb. I was too quick to remember how I took it apart ! Lol thank you again

ruclips.net/video/R93p2in3CgY/видео.htmlsi=RG1JN-irZGMyZRK5

Actually the engine is not getting too much air when it is not running off choke, it is not getting enough fuel. The choke creates a small vacuum behind and allows the engine to suck more fuel out of the jet. Usually if your engine does not run off choke the jet is partially clogged.

I had the same problem and just removed the air filter and blew the cleaner spray in the air intake pipe and it got fixed right away

Hello stupid question I haven’t been able to answer, but how do you change the oil in one of these things? I can’t find the owners manual online.

Why use these as opposed to a $25 dollar electric oil pump?

I take the plastic valve apart and clean everything. Also taking the 3 screws out of the recoil and getting it out of the way makes things a little easier and you'll be able to see all of the linkage and you don't have to fight but being able to see but I'm old and need all the light and space I can get lol. Battery tools are basically a must for saving time. 1/4" impact and ratchet are my to to along with 3/8" and then to air if needed. Great video.

Watched your video and thanks for it. I have backfires out the exhaust and intake both. My flywheel key is good, I took the head off, cleaned it and lapped the valves. My compression went from 60 to 82. Valves did not look bent at all. Lapping looked good on both valves and head. I’m missing something. Wondering about just replacing the head and valves. This is a 420 cc champion engine.

Use water detecting paste

what size socket did you use when taking cup off ?

Nice job!👏👏 Thanks for sharing your knowledge 🙏 God bless 🙌

Too much corn. Use no ethanol fuel

Every 7000 gal. Warm tanker load drops 1 percent water.

I own an RV Repair business and I absolutely love Onan generators. They are a cash cow for my business. I have been in business for 41 years and are set up to make the repairs easier than for most repair technicians. We keep a number of reconditioned Onan's in inventory and offer to swap the customers problem gen set for one of our reconditioned units for s set price. This way we can bench their unit and repair it at our leisure. Love your vids :)

Why would water be in the gas? Is it a pressure washer that leaked?

hope you didnt buy it like that!!

a felt cup... gas will flow through water will not

Gotta love ethanol. Ugh

Me personally I just pull the whole engine then maybe the wheels if they’re good.

"Easy". not.

your title should really be more specific. because it's so general it pops up as a solution for everything, even changing the wheel axle.

Well Google or RUclips was listening because I literally had said that 2 minutes before scrolling this video I was going to get up and go out and fix my power washer 😂

And it was probably stored upside-down

Holy hydrolock batman

Love the short format!

Now you don’t see a HHR often.