Видео

I installed the radian talon 45/90 with the giessle sd-c. In the 45 configuration the trigger wouldn't function properly. The trigger would barley touch the safety cylinder and it would fire but the trigger was a wall with no movement and very inconsistent weight. Switched the safety to 90 and the trigger is perfect

Due to a lifetime of using hand tools, I found I couldn't continue use the hand primers anymore, so purchased this auto primer. If viewed from above, the auto primer is offset by about 1/4 " to one side in relation to the primer tool in the die below. Anyone else had this iissue?

Thanks for the link, super helpful!! Can’t believe it’s only $15.97.

It fits. Take that shit off and install it up right, not upside down, please do that and make a review, even do so and then cut some off at the mag release, watch another video about it and it looks fab! I just got one for my USP full size.

I have a similar issue with my holster for my SA Echelon. I can draw easy enough, but cannot insert it because it is too tight at the front of the slide . Strange that they are still having issues after 4 years.

4 year old review,what holster was superior?? Thanks.

Mine is doing the same thing (dies when choke comes off, runs like crazy with choke on). Same model 125BV and it was on my patio (covered) but water got into the fuel I was using (pre-mix) and it wouldn't start for anything. Dumped it out, mixed my own gas (50:1) and after a week or so, it started, but with this new problem. Guessing the water didn't help much, but for some reason, not getting enough gas at the 'open' choke setting, and it dies. I think the gas filter is screwy now and the fuel line might be gunked up somehow. That'll be my next job. Maybe some Dry-Gas will clean up the mess from the water? Yeehaw!

Does the medium have Any tension at all?

That is your fuel filter, and the fuel lines were corroded due to using fuel with ethanol in it.

Thanks for the demonstration!

Where is Hungaria?

Hungaria?

My dude working on his blower on top of his blower 😂

My first purchase when I turned 21

so, what was the problem?

yeah.. I had all the same problems stated here.. finally had a slightly misshapen primer get stuck in the small tube... no luck getting it out so that's wasted.. I've also had issues with the hand priming tool feeding 2 primers onto the pin..

Right away I noticed that while this uses romanian parts. They are not the same parts made in the Romarm factory that produces military rifles and parts for wasr 10's. This looks like a nova modul rak-1, or parts from it. Which is made in a civilian plant in cugir romania. I see parts kits from this factory pop up for very cheap to this day and stay away from them. Get something that you know was made in a real state arsenal that produces military rifles.

You are grandpa and you are not dad thats the reason that you installed the grip by the false way, delete this video because you had installed false, i bought this hogue grip and i installed on usp conpact by the true way and it fits perfect, i think grandpa that guns is not for you i advise you to stay away from guns.....

You must delete this video because you are so stupid and you installed it false 😱 (upside/down), it fits excellent if you install it in the right way!!!!

My 12 yr old German made SOLO LEAFBLOWER also needs the choke to be on to run.If the primer bulb is full or mostly full (mine is ) does that say that fuel is flowing? I changed the fuel filter,( the fuel filter is the same as yours and I put a different one on.That is all the hardware store had.I cleaned out the fuel tank vent,took the Carb off and cleaned the gasket(it looked nearly new )I tried running it with the air filter out.No go.Made sure the Carb.was clean.Could it be that I need to simply replace the fuel lines eventhough they look good at least from the outside.I really luv this quality SOLO leafblower and hate to junk it.Any ideas would be appreciated.

My misr 90 is tenfold better than that, lol Best advice I got was - IT'S A FREAKING AK, GRIND THAT STOCK TO FIT

I think that is more geared toward precision shooters

Century Arms bft47 put 11k round through it took it to get inspected there’s nothing wrong with it. That was 800$ so the newer us made ak’s are much better made than the earlier ones

Finally

Sirs Which variant of Ak47 is popular for long period of time ??

Romanian aks are made on the same Soviet block tooling as Russia , best aks on market

Just tell your story!! No need to put others down while doing it, at the end of the day you own an AK-47. "I OWN A FEW HAND GUNS AND I'M FAN OF NAVY SEAL MOVIES", YOUR SHOWING US YOUR AK-47, man stop!! You like guns!!!

If anyone is interested, I'm getting 2,850fps (SD of 12) out of a 20" AR with some moderate smearing from pressure using the following: 25.2gr Shooters World Match Rifle CCI 450s 77gr Sierra TMKs Nosler match brass Loaded to 2.3" (PRI mags allow that) Note: this is way over recommended, so work up and watch for pressure signs. Accurate 2520 is very close to this powder...in fact this powder is the original formula for AA2520.

Thank you for your help!!!!

My blower only works with hald choke. But I have the same model you are showing.

And you put it on upsidedown.....that does make a difference

On the older hk anyway that is....

Its to small for the compact......

It is for a full size hk usp fits perfect ......

125B did everything, carb kit, new plug, new Carb, new fuel lines, new fuel filter, checked the spark arrestor, no issue with motor mounts. Still runs like shit..will not run, I have the spark ignition ordered but I do not think that's the issue. Not much for carbon in it and need to find a carb adjustment video I suspect maybe the carb mount rubber housing .

It is the Tapco trigger, most likely. The hammer has a hump that will eventually smooth out.

Never had an issue with them dumping unless I pull the tube or things aren't aligned right.

I concealed carried a xdm-osp 10mm with a black rhino holster under a short sleaved button down. The holster came in two weeks never had an issue with mine...... hmmmm

Have you installed a trigger since then?

Do you have a part 2 follow up video? Also would love to see this for their 300 aac 208gr amax.

Trashcan is the best place for these.

I was just told 1200 bucks for this exact gun ! Seemed retarded? Does that seam right??

I have a Romanian part kit build from 1967 and I have a WASR 10 current production. The difference is night and day.

Will it hold AK mags?

Do you still carry this gun?

Who made the holster? Thanks

Same about the handle!

Lack of maintenance does happen to these machines all time.

Simple . Theses guns run in all territory. Snow l , heat . Mountain and jungle , these rifles are steadfast

I would recommend you _NOT_ buy a bargain basement or "budget" AK or any thing for that matter. In America you do not need to do this as there are many, many other (honest) ways to get a "good" or great AK. Foe example: - save up, you don't need the rifle right now, put two (2) or three (3) dollars a day in a piggy bank and in a year you will have enough to get that sweet AK - buy used, Gun Broker or you local gun store probably has some use higher quality used AKs - Pawn Shops have previous owned AKs check them out. God bless