Видео

DUDE I been trying to figure this out for months!! So many different shops told me diff things. That’s exactly the rattle noise my car makes. will replace tensioners soon

I have had these sitting in my garage for 2 months because I couldnt figure out how to put them in…now i have a weekend project on my hands

That exhaust port screams "Put a turbo in here!"

thats pretty helpfull dude. Thanks:)

Brilliant! Thank you for this. Great presentation; straight facts, no fluff. Very appreciated.

Nice work. Thanks for posting!

Really appreciate this video. As the owner of a 1990 NA6, I'm happy to hear that the short nose crank thing isn't really a thing (if you follow directions).

Great video. Thanks heaps!!

this but im tearing down an lycoming o-320 engine for class 😝

Very detailed - good advise on possible failure/problems! Thank you very much

Had the same problem with my water pump pully

My miata is a 1991 swap to manual for a long time a few years swap the engine after that the signal starter sometimes work sometimes no I know everything is new starter battery checking the diagram cruise control and transmission module must be bypassed ?????because I just bypass the interlock switch

How long does the swap for an NB2 take?

i’ve never understood this? i just put my arm down the side and grab it?!? maybe easier as im RHD?

Thank you! RUclips miracle! Clutch went out in NYC. Gonna head home carefully thanks to you!

Just bought an 04 msm doing my nerd video binge before I pick it up Wednesday. Great vid earned my sub, also sweet shop!

So what if it's the opposite? Trying to run a/c. Driver side is hot, passenger side is cold

Stupid question: I need to adjust my TPS. Where do I insert the feeler gauges? Like where is the throttle stop screw? Is that bit at 5:25?

I’m

Thanks for a fast response.😎👍🏻 I especially appreciated your video and information on the electrical part of the manual swap. Very thorough , I was just overthinking the clutch pedal wires . I’m finishing up the exhaust on my 2000 MX5 5 speed swap. I can’t wait to slam some gears!👍🏻💯🏁

You don’t mention what has to be done if anything to the two sets of plugs that are on the clutch pedal itself. One is a white two prong plug. The other one is a sensor attached to the assembly that has a very small two pin hole. Do I have to do anything with these or is everything else covered in the Breakdown of electrical requirements for the swap?

nice! i just bought my second one last week!

hahahahhaa i had a similar experience recently, ultimately a sigh of relief when i foujnd it was a feul filter slapping the chassis rail

HOW DO I GET THOSE BROWN SEATS AND DOORS FOR MY MSM?

Great reference video! Someone else built my car and I'm rebuilding it now, I don't know where anything goes 😂

Thank you for another great Miata overview video. Hoping to get a Mazdaspeed Miata someday and I really appreciate that you put this video together. The step by step walkthrough really is so helpful. Excellent video as always - thank you!

Until you explained it was a 1 of 1 custom I assumed someone had taken the interior from the 2002SE and swapped it over.

WOAHZA

I've watched all of your anatomy videos

I’d love to own one of these!

Awesome video. Very unique and appreciated.

Do you think the throttle cable will work with the 1.8s other throttle body that only has one slot instead of the two slot that you have on the car?

Do you know how it happened? Did the gasket roll back when you've put the cover back on?

Or remove the bracket holding the intake to the engine, you’ve already removed two of them at the top of the mount

Amigo amigooooo me pasa lo mismo y estoy desesperado porque no se qué es, es la bomba o el filtro de combustible? Gracias enserio por tu vídeo slaudos desde Guatemala

i gotta say the slave cylinder IS different, there is an early '90 style with the nipple on the slave cylinder rod, & a later '90 & the nipple goes into the clutch fork on the early '90 NA

OK, first off - thanks for a great video and list of parts.. But what happens when I turbo that engine before installing it? Im planning a Kraken full kit with COP and MS3 ecu... do i still change over the valve cover? Am i using the crank angle sensor now? What gets handed to the MS3 to take care of vs me having to retro it off the engine to mate up with the NA8 ecu?

E-cool, saving all that intercooler plumbing

thanks a lot for this very clear video that explains very well how it works on a Miata NA and NB Miata ! 👍

Hey man. So what’s the black can/fuel filter looking thing with vacuum lines going into it. Near the coolant overflow reservoir.

Just pull the whole motor out it makes it much easier

Yo the cover is clean af

is all the wiring you need to do or is there anything else

Was ‘98 an orphan year?

Great video. Wish I had watched it before I adjusted the lever! I have my first Miata and so have never seen any weirdness such as this. Been turning wrenches for 40 years.

Good informative video of the miata MX5

Thank you again.

Amazing video. Subbed because just after watching 2 video ,I know more things about my car. I’m building my first drift car on mx5 based ford popular

You poor fools. VVT has given me so much pain in my NB2. Do not do it.

Dam lol ! That’s pretty bad. Ur car was still able to run like that ??