Видео

Just the video I was looking for. Wanted to see how the 1.5 worked just topping off tires. Thanks

Aren't most of these inflators from the various RED Chinese manufacturers rather anemic either in whole or part?

What is the part at 2:00

how does it lock into place without a picatinny og the glock?

Great Car and even better T-Shirt!

bro well watch out

bruh

I'll take it off your hands bro I potato get it .

You also drove about half as much as the average person. 30k miles in 5 years. I assume your cost would have doubled with additional services and maintenance.

Thanks for saying sir

Awesome job! Thanks!

Thank you for the video.

Ty ..nice work

How to learn to do all the work on Panamera? I only know how to change the tiers on my Honda

How to learn to do all the job myself on Panamera? I only know how to change the tiers

very helpful thanks mate

It’s a miracle Nobody in real world competition wold set bullets like that

I was told by a gunsmith to swap the spring to remedy cycling problems. Have you heard of this? (On the Walther)

Does the zipper actually accommodate opening the driver's side door easily? I'll be putting my G35 coupe into storage for about two months, so I want my g/f to be able to open the door to start it every week.

Does the zipper actually accommodate opening the driver's side door easily? I'll be putting my G35 coupe into storage for about two months so I want my g/f to be able to open the door to start it every week.

My sister gave us her 05 RX330. Wow. So many parts missing from under the hood from all the "service" done to it over the years. Some of the lower panels were missing. I just went ahead and removed all of them and left them off so I can access underneath for a while so I can get access and "see" what's going on. We don't live in an area where they salt the roads. Why put the lower covers back on, I ask myself. That is a clean engine! How do you keep it so clean?

Been trying to remove the cap on my G19 Gen3 but not going well. Thought about just getting a new rod but having a hard time finding one. Any other tricks I could try?

The barn was dark and she ran when parked. I mistook the center hardline on the rack for a tow loop. Towed the Pony Car right up to the carport no problem. One new distributor later and I'm doing burnouts. But the PS pump is groaning louder. That hard-line is IN there. So I watched this and am reading the Haynes Manual. Great video. I've seen it happen now. A little PB blaster and A LOT OF PATIENCE! Looks like I may be taking the rack out if I can't get a flare nut wrench with a custom bend in there.

How about in 2024 is it still reliable car?

I got a box this past weeknd for 10bucks when i baught a box full of 9mm brass he also gave me some xtp 115gn for 10bucks all in all i spent 30 bucks it was a steal just with the gold dot

Air suspension issues = huge bucks

The fractures on the front brake pads may be from HEAT FRACTURES when EXCESSIVE HARD BRAKING 😎

Mike that’s not the MAP sensor, that’s the heater element. The MAP sensor is at the top rear of the intake manifold.

I would agree with all 5.

I scaped my passenger front wheel going through Taco Bell. 😂😂😂 It's funny now, it wasn't then.

Or you can get the regular stack on gun cabinet. It doesn’t say ammo on it and you can stack it full of ammunition and it doesn’t advertise and it’s just as good.

Thanks for the video! I’ve had two of these Kayme covers now. Just wondering what you went with recently and if you’ve found a better one?

Can I use this product on ceramic coated cars

I thought this was a joke video 😆😂😂😂

I got here because I have a 302 HO that a previous owner put in my 1966 F-100 pickup. I thought a GT40 was an old Ford race car, one like at the Simeone Museum in Philadelphia. I'm 76 and forgot some of what I did to set the lifter preload in 2020 not long after I bought this truck. The specs for setting the preload to about 20 pound torque are confusing, different amount of turn from 1/4 to 1 full turn, but not consistent in opinion. After the heads were machined before I received the truck the stock pushrods were not long enough, so I had bought 6.300 and used different shims to set preload, from .020 to .040 inch shims. I want to do this again following firing order this time rather than other techniques. It is a little noisy since I changed oil recently.

Where did you get a 2 inch lift spindle? All I can find is a 3 inch lift spindle and it appears that when installed it raised the front too high such that the rear would be lower than the front.

What a moron. Buying a car that needs to keep topping off oil.

Great video

About to have this device

you save more cash upfront but you will actually pay more in the long run buying online. I have 5 year warranty and free replacement on new parts through the dealership.

I'm very surprised at your 70 MPG RPM number... I swapped axles in my 81 Capri when I put the T5 behind my 351w interceptor engine... at 70 mph I had 2000 rpm with 308 gears and factory size 16 inch wheels (GT wheels from a 92, my cousin's... lol) Is your car an automatic? Biggest problem I had, and how I ended up with my cousin's 16 inch wheels from his 92, were the brakes. the 11 inch front rotor and 9 inch drums were only good for about 70 mph once.. and that's 70 to 0 or 140 to 70... that car was incapable of 140 - 0 in one stop. My cousin put the SVO brakes on his, because after we put the Whipple on his, it would outrun the brakes every day of the week. Had the MAC shorty 351 conversion headers, off road H pipe and 2.5 dynomax mufflers with the polished stainless LX style tailpipes, sounded great!

Agree the getting the pinch bolt out and spreading is key! I’m on day 2 and getting it back on is a FN bastard

Not the same for Gen 5

I ordered one and I just got it and it looks thin and cheap, it doesn't look nothing like the one on amazon , it looks like it will rip at first wind.

dude exhaust is almost worthless until you yank those 4 cats out. runs better and sounds way better

Will I need an alinement after I replace my oem one to lowering spendel

Wish my $130k sticker panamera had a back up cam. Like how tf did the original owner not spec a camera in on a high spec car

Hey Mike, I have a question, I have a 2010 panamera 4s, my oil temperature, and coolant temperature, have been rising, I'm trying to locate the oil temperature sensor, any advice?

The left over o rings are for the float valve , and the fuel inlet pulls out , the mid body has 4 tiny o rings.

So it was bought as a 7-8 year old car, with less than 20k miles? I think the costs are reasonable for a Porsche, however given the total miles i would hope not a lot has gone wrong. Great vid btw.