Видео

did you install the headers through the bottom of the car?

I wish you good traction, a car that doesn’t break down, and lots of podium finishes.

Really cool! Great driving, solid runs. Subscribed !

💫👍

🔥

Great video. Tips for those who need em lol. When installing put the driver side rear axle on first. Zip tie the passenger side axle up out of the way. Jack differential up with the drive shaft aligned. When you jack the differential up and work it within the mounting bracket slide the 2 front bolts in then work the other axle in place. Then play around with the rear bolt til you get it.

Damn that diff is toast

Now that's how you drift a Mustang👍🗿

Was listening while driving to work and I kid you not at 4 minutes in my car breaks down

That entry on the Top8 lead against the e36 was beautiful

Hi buddy, great video, thanks for sharing. I have install the same pump but not drilled anything because I'm planning to install a radium surge auxiliary tank and they request to the oem pump housing not to be modified, then I have installed the aem pump without not drilling anything. I have genuine GT-R injectors but I didn't install them yet, that is coming next. After the installation of the pump, and first start my idle it's a bit low and looks like it's bouncing up and down between 650 and 700 aprox..... the car drives ok and all seems to work but this fluctuating idle it's worrying me a bit. I'm not sure if this is normal or not, In theory the fuel pressure should be the same....oem regulator not modified but I suppose because more flow the car will be more reach even with the oem injectors....I think the ECU is trying to compensate that is why the idle is fluctuating. Did you experience something similar? Do you consider this is normal before the tune... I would like to know before I install my injectors and the rest of the bolt on's to discard a future incoming problem. Thanks in advance!!.

Good job this season brotha! Hope to battle more next season! - Konrad

screw that guy driving the yellow e36

🔥

Amazing video just finished replacing mine on a 2017 CTS did it step by step it was time consuming but well worth it!! Thank you!!

and meat 😂

beautiful video very well made. in my case ill pass and just go to the dealler because if i'm doing it my self ill destroy the car

Youre not running the front plastic undertray? I want to mount mine to the radiator but i need to keep the undertray. Im worried it'll block all the light...

I dont know whats wrong with GM cars..I live in Qatar and my CTS 2015 differential gave up at 55K miles. Not sure if its the extremely hot climate to be blamed.

Cómo cambiar el diferencial delantero de 2012 4x4

Good video!

Nice video! Would it be worth it install this plenum spacer on my 2005 350Z convertible with an automatic transmission? I drive conservatively, rarely exceed 4500 RPM, and the car already has over 120,000 miles on it. Thanks.

I did it thanks It looked complicated but got through it

how much did you spend??

Did you have check engine n it when in limp mode?

Was this in so cal ?

If you/anyone haven’t figured out how to get the weld BBs off try a chisel and hammer. Coming from a welders perspective.

1500psi it goona burst the burst disc

1st time? Great job 🎉 good video

🔥

Hopefully you find the restriction in the turbo kit, update us on YT if you do! Car is sounding and looking good!

а отстрелы не думал сделать?

flavorexpress is awesome

bro what’s that dual caliper set up on your rear discs? edit- i’ve come back to say i’m stupid it’s for drifting

Hello are you in Atlanta GA.

Thanks!!

“How to” but doesnt show steps. Wtf.

In order to remove the OEM steering wheel you will need a tamper proof torx bit.

Might have an exhaust leak brother?

Thank you!

Excellent video

Just curious if that replacement screen is still holding up. Obviously, that also depends if you still have this car. The reason I ask is that I've heard that some of the lower priced replacement screens don't last very long.

What mm size was the large bolt you had to remove?

Who lives in Northern VA? come do mine please.

WOW - Had no idea it was this complicated. You made it look like I could actually do this! Very detailed/well-explained video. Thank you SO much. I'm going to give it a try.

Thanks for the video very useful took about 1.5 hrs.❤

Do you get 53 to 63 PSI with that pump? That's what the manual says it should be. The pump I have now pumps 40psi at idle and about 48 on load.

Gave ya a comment on your 350z valve covers LmK

You only put RTV on the Two left corners Thast It???

⚠️DANGER TO MANIFOLD⚠️