Видео

Thanks for the detailed walkthrough. I'm going to try this tomorrow, since it is late night now.

The handle was loose, but I did not need spacers. Watching the video I realized where the little screws were. I did not even know screws were there. I found my smallest screwdriver and tightened the handle back. Thank you guys, you saved me a $75 service call. I will stay tuned. By the way I'm an 81 year old great grandmother.

Not wanting wood. That’s so uncomfortable I Want the material so we enjoy sitting in it.

I thought you had to replace the whole thing. Thanks

What’s the solution for something like this.. but 25-30 feet high? 😖

I’m doing something wrong. Mine wouldn’t move a muscle trying to rot it out

Can I just say how much I appreciate you showing us how to take OFF the light itself. Every other video starts with it already off and completely negates the point of finding out how to replace it!

Ours sit so tightly on the ceiling that whenever we try to oull down the plate it chips away around the lamp. Terrible design or installation in my house.

Thanks for this video! Couldn't see what I was doing, but knowing (now) how the metal clips worked was a game changer. Appreciate it.

Thank u

This video still helping in 2024. Thanks so much!

Thanks to this video I knew what washers, spacers, and set screws I needed. Picked them up at Lowe’s and Home Depot and was able to fix this towel bar that has been loose for over a year! Thanks so much! 🎉

Can't thank you enough for this. You'd be amazed how difficult it was for me to find a video I could follow never having started a generator before. I don't friggin know what a choke or prime or whatever looks like so it doesn't help to just say the words! You gave me specific visuals, in order. We haven't had power since hurricane beryl so I really needed the generator to start and stay running. Thank you very much!!!!!!!

Always make sure to clear a ‘getaway’ path before you spray.

Hey brothers, what all would the unit power at one time?

Thanks dude! I didn't want to break them trying to figure them out. Much appreciated.

great review, no useless jibber jabber, just right to the point demonstration 👍👍👍

My disng is a super rare and awful one with the bulb houses in a aluminium canister, and the light and glass came attached to it. You have to carefully rotate the plastic clip that goes on the ceiling, but I don't know how to remove the glass part. I'm guessing you pry it, but I'm scared it might break.

How To Change A Recessed Light Bulb*

I feel ya bud Ive got 3 sons drive me NUTS also.

Let's see my fat ass rip through those!

Nice! I was looking at other videos on how to replace the fabric. Your video with the wood is just easier to fix and looks so much better….especially with the stain added. It will surely last a lot longer than the cloth replacement! Great video that didn’t waste my time with extra talking about nothing!! Thanks man.

I rate it an 'uhggg'.

Jason! Pleasant surprise seeing you here but you're a big help!

Hi. Thanks for the great video. Hey hope ok ask questions. I want to get the newest version of this one and was wondering, the one you have has if harmed any of your computer type sensitive type electrons or everything was ok? People keep telling me that unless I get an inverter generator that this one will make what they call dirty power where the electric wave can damage stuff that's sensitive, they said the THD was at a range of 25% or less. I don't know anything abt generators so just wanted know if your stuff you powered from generator was all ok and did you run it for a lot of hours with computers and sensitive stuff? I'd sure appreciate if everything turned out ok still. Enjoy your channel and subscribed. Thanks again

Ahh. Thx!

I made it by myself thanks to woodprix.

What size plug I need

Thank you for the demonstration.

Looks great, sir! Plus its now much more sturdy than before ✌️

Great video. My problem is I can't loosen the bottom screw. The allen wrench sits fine, it just dead-spins and won't loosen so I can separate them Anyideas?

Thanks so much for this video. I wasn’t familiar with the design of recessed lighting. This was super helpful.

Thank you so much for sharing

My check list to perform this great ( for me) feat. 1. Watch video. 2. Convince self I can do this. 3. Put towel down in tub ( light is directly under the bath tub). 4. Pray hard. 5. Watch video again. Put step ladder in tub on top of towel and begin the climb. 6. Remove the cover as instructed in this video. 7. Stretch arm as long as possible while succumbing to the fact the lightbulb is stuck and only way to get it out is to go to the top step of the ladder. 8. Climb down ladder. Take deep breath and pray again. 9. Look straight up at the lightbulb and proclaim "I will triumph!!" 10. Climb up ladder to top stop whilst praying I don't fall. 11. Unscrew stuck lightbulb; replace with new lightbulb. 12. Turn on switch to make certain new bulb is working. 13. Scratch head whilst attempting to figure out how to get the clip back into place. 14. Watch video again. 15. Grab flashlight and announce " Oh little clippy holder thingy where are you?" 16. Squeeze clip and place back into clippy holder thingy. 17. Place cover back on 18. Climb down from ladder ; feel a degree of pride. 19. Thank God for protecting me. 20. Turn on light switch and proclaim "Success!! I have triumphed!!! 21. Post to this video with a great deal of gratitude; excellent instructions. ❤

Any update? Still work?

Starts at 1:20 after all the talking

That did not work 😢it's very tight!

I bought my house 4 years ago, and the living room has two rows of recessed lights, one on each side of the room. They went out on one side, and I thought maybe there was an electrical short and was going to call an electrician when I could afford it. I never thought about light bulbs being inside of them! 🙄 Thank you for helping me fix this myself and save money! 💰

I purchased this wrench after watching your your video 2.5 years ago. It's worked extensively well for me. The battery life is fabulous. Thank you for the video.

Thank you for posting this video. Now I can change out the bulb without begging my husband to do it...

can i use this tool with flap discs and sanding discs to use as a grinder?

Thank you sir.

thank U

Thanks a lot! This really really helps me improve my household skills 😊

The new bulbs don't last that long

Thank you for the great demonstration! I just bought my Ryobi circular saw this past weekend and I'm doing a master closet rebuild. I'm super excited to get started using my saw!

The part that the piece on yours goes into the silver metal clip, mines freaking plastic and has broken off on both sides. Idk how the hell to find only that piece and if I could change the plastic out for metal. I’m so pissed with the builders of this house. My grandparents got robbed. Everything these people did was cheap cheap cheap. Finding it all out now 8 years later

Just what I needed thank you

thank you sir

Thanks! These are the types of things they don’t teach new home owners. 😁