![YourLocalWellMan](/img/default-banner.jpg)
- Видео 26
- Просмотров 103 160
YourLocalWellMan
США
Добавлен 3 июл 2022
There's a new Well-Man in town
Видео
Repairing bent blades on an 8ft Aermotor Windmill!
Просмотров 3052 месяца назад
Bolts fell out of the mass pipe, causing the motor to fall. Boss and I fixed it and repaired the fan blades.
Taking the guts out of an 8ft Aermotor windmill!
Просмотров 1,1 тыс.6 месяцев назад
The mill was never oiled and wore out the large gears and arms, luckily the pot and hub were fine!
Replacing a shot 8ft Aermotor windmill!
Просмотров 2,2 тыс.8 месяцев назад
The Boss and I take down a bad mill! #aermotor #windmill
Pulling a 2" plunger with fiberglass rods!
Просмотров 5269 месяцев назад
The boss and I pull an 8-rod deep well to change out some bad leathers!
Helping the Uncles out by changing 8ft Aermotor windmill for solar-trailer!
Просмотров 84211 месяцев назад
The family and I take out a windmill for solar before the upcoming heat-wave hits!
Changing 10ft Aermotor section on tower!
Просмотров 858Год назад
The crew and I change out a bad section on a 10ft Aermotor
Fixing a tipped tower and badly mangled fan on 8ft Aermotor!
Просмотров 3,7 тыс.Год назад
The crew and I fix a tower that has tipped over along with a pretty banged-up windmill!
Changing out a wooden windmill tower for 8ft Aermotor!
Просмотров 4,1 тыс.Год назад
The crew and I change out a wooden tower that was about to topple over!
Saving a 10ft Aermotor from tipping over!
Просмотров 1,6 тыс.Год назад
The crew and I repair a damaged stub tower before the motor has a chance to fully fall off!
Fixing broken break parts on 8ft Aermotor windmill!
Просмотров 4,2 тыс.Год назад
Fixing broken break parts on 8ft Aermotor windmill!
Fixing a broken tail spring on the In-law's 8ft Aermotor Windmill!
Просмотров 2,3 тыс.Год назад
Fixing a broken tail spring on the In-law's 8ft Aermotor Windmill!
Replacing a badly damaged 8ft Aermotor windmill with a newly overhauled Aermotor wind-engine!
Просмотров 1,7 тыс.Год назад
The Crew and I replace a bad motor with broken arms along with a good chunk of the pot broke, leaving the windmill useless!
How a water well is drilled!
Просмотров 517Год назад
The crew and I clock one last well in before the end of the season!
Converting an 8ft Aermotor windmill to solar!
Просмотров 4,3 тыс.Год назад
Converting an 8ft Aermotor windmill to solar!
Decommissioning a well goes rather poorly for me!
Просмотров 566Год назад
Decommissioning a well goes rather poorly for me!
Full process of finishing a well for an Aermotor windmill!
Просмотров 3,1 тыс.Год назад
Full process of finishing a well for an Aermotor windmill!
Replacing bad legs on an Aermotor tower!
Просмотров 880Год назад
Replacing bad legs on an Aermotor tower!
Fixing a mangled Bottom Furl Lever on a 10ft Aermotor windmill!
Просмотров 7 тыс.Год назад
Fixing a mangled Bottom Furl Lever on a 10ft Aermotor windmill!
Replacing a broken Aermotor windmill!
Просмотров 47 тыс.Год назад
Replacing a broken Aermotor windmill!
Using a Heavy-Duty Rigid Threader on 3" pipe!
Просмотров 410Год назад
Using a Heavy-Duty Rigid Threader on 3" pipe!
Converting an eight-foot Aermotor windmill tower into a ten-foot
Просмотров 14 тыс.2 года назад
Converting an eight-foot Aermotor windmill tower into a ten-foot
Disassembling an eight foot Aermotor Wind-engine
Просмотров 1,5 тыс.2 года назад
Disassembling an eight foot Aermotor Wind-engine
❤❤❤❤
beautiful!
Thank you!
👍👍👍👍👍
Appreciate it!
👏🏿👏🏿👏🏿👏🏿
Appreciate it!
That’s hard labor, what a small platform to stand on. My 10 foot mill has a 2’ wide walk around platform. I can use a 6’ step ladder on it, to get up to the helmet. Nice video.
Oh yeah, some of them are sketchy! That sounds like a very nice one to work on! Appreciate it!!
If I have 3 fins that are half broke on opposite sections. Am I able to replace that one fin? And keep the others ? Can't seem to find any videos pertained to my question. Thank you
If you take the damaged sections off and grind and drive out the rivets on the damaged fin. You should be able to put a new fin on with bolts
@@yourlocalwellman thank you for the quick reply. Will do thanks again.
Of course, sometimes the rivets do not come out so be ready for a battle!
Nice work
Thank you!
Never saw it work
It works.
Could you show us a little closer the piece you screw into the mast pipe before setting a head on, did you make it?
Yep, took a mass nut and welded a pipe on it, then rounded the end to make a point to help it get started as well as filled the middle so it wasn't hollow! I'll try and get a closer view of it in the next video!
Could you show us a little closer the piece you screw into the mast pipe before setting a head on, did you make it?
Good videos
Glad you like them!
you must be very brave and tempted to climb the tower W I T H O U T a harness
Something like that you could say 🤣🤣
Aermotor trabaja con metales en eje de masa .cojinete de engranajes y buje corto de piñones
Aca en Argentina trabajo en una fábrica y es muy parecido el molino muy buena maquina .los arme durante años
Una pregunta tiene colector de aceite en la masa
Lo mejor Aermotor es ARGENTINO O PARECIDO
Hello, i will be taking down an Aeromotor windmill in a few weeks. For taking the head off there is no pump attached. Only thing a guy has to do is take the cap off, and unscrew the nut, and hook up the crane? Are all Aeromotor windmills the same in taking apart. Any info is appreciated. Thank you
Hello! Yep, as long as there is no swivel rod attached to the motor, you should only have to take the mass nut out and pull it off. As far as I know, all Aermotor windmills should be the same when taking them apart!
@@yourlocalwellman Thank you. If I'm needing parts once I take it apart. Do you have any suggestions on to purchase from?
Well, that would depend on where you are based out of, I don't know a whole lot about parts on the sales part of things outside of nebraska!
Where did the blades go?
They got scattered all over the place when they broke off! If you look around the rig when I'm up on the tower, you can see some of them!
You think I could weld a nut to a snapped vane spring mount to get it off?
I'm assuming you mean the part that sticks out of the base of the motor that you slip the spring onto from the tail. In that case, I don't see why that wouldn't work! I would try a pipe wrench on it. Probably would get it off, too!
What is the deciding factor for switching from an 8ft to a 10ft mill ,or any size in general? P.s. love what y'all do
It mainly depends on how deep the well is. Anything over 100 ft people start considering 10 ft motors for the extra pull power and less wind to start spinning! Thank you, we really appreciate it!!
Hey man. I had my cylinder replaced down hole (180feet of pipe) on my windmill powered water well on my property and still no water pumping out. Haven’t heard back from the guy that replaced. Wondered if you might have an idea. Thanks!
Well, my best bet with a new cylinder, especially that deep, would be that they didn't get the check seated quite all the way down, or the leathers haven't spread on the new plunger, I'd first try and pick up on it if you can and drop it on the bottom a time or two and then yank up on it fast to try and spread those leathers!
Ok so just so we are on the same page. I would have to unhook the sucker rod from windmill and then hook up to the piping and drop it down a few times and yank it back up?
Yep, so make sure everything is disconnected from the windmill, and then let it drop onto bottom a couple of times to try and get the check seated down, then yank up as fast as you can to try and spread the leathers on the sides of the cylinder, might be tough to do by hand 180ft down depending if the leathers have already spread or not!
Sweet thanks man! I really appreciate your help
Of course! Let me know if that doesn't do it!
We have a lot of aermotor windmills here in NW Missouri. I love the oil Ring inside the gear box . Windmills are beautiful!
They sure are! Always refreshing to know they're still so abundant!
Parabéns 👏👏👏👏. ótimo trabalho 🇧🇷
Thank you!
Great..I work on windmills too.
Gotta love it!
👏👏👍
Looks great! Would love to see how to remove the main shaft and hub.
I hopefully should have a complete overhaul video up before too long!
Really cool video! Thanks for sharing
Thanks for watching!
JAYZUS--the talent and skill of throwing up and catching that uge wrench!!!
Trust me, there have been many failed attempts before!
Hi, i am from Argentina and i have a question. How can i know where my aermotor windmill will can has a scape of oil? And how can i fix it? Thanks
Hi! And are you meaning there's a leak that you can't find?
How much water daily in gallon's are you getting and how much gallons per minute douse it give approximately ?
That depends on a decent amount of variables, what size the check and plunger are, how deep the well is, and what motor head they have one but on average a 2 3/4 plunger can pump 3-5 gallons a minute on a good day
Bien
Was the replacement a new or rebuilt motor?
This one happened to be a rebuilt motor!
What's shot about this one?
Little gears in the back went out, so the two sets weren't touching!
@@yourlocalwellman wow. How many years you reckon its been up and running?
It's hard to tell. I couldn't find a date stamp on it, but probably in the 20-25 year range if oiled properly
I have built windmills for nearly 60 years. If you wish to pump water, going forward, a Savonius VAWT can be mounted on a bypass single-post tower on an off-set bushed shaft with a terminating-end pointed thrust bearing, using a worm-and-down-gear crank AT GROUND LEVEL for peanuts ($) and you never have to climb another tower! I am currently building 100 such windmills, which compress air.
I'm 75. I reinforced my tower base and welded on hinges and a counterweight to lower and raise my windmill tower by hand for maintenance. Also, if you would hinge your tailfeathers on a 45° slanted pivot, so it could rise on either side, you could get rid of that furling spring and lock, controllong furl by the amount of weight on the outboard end of the tail.
Nice work!
Thank you!!
Just a random weed plant
Grow everywhere around here, always in the way!
the king returns
Quick question for ya. On my Aeromotor the wood I cut for The plunger rod doesn’t seem to last, would a chain be a better solution? Thanks!
As long as you aren't having problems with your well sticking, then yes, a chain will give you way more miles!
❤❤❤❤
great stuff
Thank you!
Yellow shirt is bae
Great videos! Keep them coming.
Thank you so much! I'm trying my best to keep uploading, hard to get footage and not die in the heat
What type oil do you use/recommend?
We use drip oil, but any kind of thicker oil will do!
I love old and dirty windmills ♥
Me too!
Good job , beautiful #8 aermotor windmil ♥
Thank you very much!
Girlfriend reveal!!!
My man in the yellow shirt is clueless
How many English bulldogs would it take to fill up a 83 ft by 118 ft aquarium?
1,632.33
thank you so much
Exmoor once again welcomes,the little train to lynton