![Marcel Boudreau](/img/default-banner.jpg)
- Видео 28
- Просмотров 14 280
Marcel Boudreau
Добавлен 15 дек 2009
Misc things I'm involved with including: beekeeping, woodworking, legal/safe firearm use, and whatever else catches my fancy..
Bench top rapid tool mount
Example of my rapid tool mount on my workbench.
The example shows an install of a quick vise.
I use similar mounts for an arbor press and for two different ammunition reloading presses.
The mount plate is made of two layers of 3/4" plywood glued together with the top and bottom perimeters rounded over using a trim router and a 1/8" round over bit.
Unfortunately when I made my first mount plate and drilled the holes in the workbench, I did not make the hole pattern symmetrical. This means I cannot easily layout holes in a new plate but instead I have to trace hole locations from any of the existing plates. I regret this issue but I'm not about to redrill all the holes and reinstall the T nuts ...
The example shows an install of a quick vise.
I use similar mounts for an arbor press and for two different ammunition reloading presses.
The mount plate is made of two layers of 3/4" plywood glued together with the top and bottom perimeters rounded over using a trim router and a 1/8" round over bit.
Unfortunately when I made my first mount plate and drilled the holes in the workbench, I did not make the hole pattern symmetrical. This means I cannot easily layout holes in a new plate but instead I have to trace hole locations from any of the existing plates. I regret this issue but I'm not about to redrill all the holes and reinstall the T nuts ...
Просмотров: 167
Видео
3D Printed Mason Jar Small Parts Washer
Просмотров 142 месяца назад
A small 3D printed basket for washing parts in a tall Mason Jar.
Cardboard Hot Box
Просмотров 306 месяцев назад
DIY Hot Box made from a cardboard box, a hair dryer, a couple of bungie cords and a pair of 3D printed anchor tabs. I use it for drying cleaned rifle/pistol brass for reloading or for drying spray painted parts or drying anything that needs a hot/dry location.
3D Printed Arbor Press Punch Adapter Movie2
Просмотров 187 месяцев назад
3D Printed Arbor Press Punch Adapter Movie2
3D Printed Arbor Press Punch Adapter Movie1
Просмотров 117 месяцев назад
3D Printed Arbor Press Punch Adapter Movie1
Movie Option 1
Просмотров 419 месяцев назад
Video in support of my Thingiverse item 3D Printed Electrical Extension Cord Pass Through Gate
Movie Option 2
Просмотров 479 месяцев назад
Video in support of my Thingiverse Item 3D Printed Extension Cord Pass Through Gate
3D Printed Tank Indicator Tag
Просмотров 153Год назад
A short video showing how to assemble my 3D Propane (or any tank/container) Tank Indicator.
3D Printed Stencil Design
Просмотров 6882 года назад
Here's the basic process I use to create a simple text stencil that I then 3D print and use with spray paint.
3D Printed mason jar bullet/powder strainer V1
Просмотров 882 года назад
This strainer slides into the opening of a mason jar. It is not attached other than the slip fit.
3D Printed mason jar bullet/powder strainer V2
Просмотров 792 года назад
This strainer attaches to a standard mason jar using a standard lid ring.
Laser Cut Movie Maker's Slate
Просмотров 174 года назад
Inspired by Adam Savage's one day build (ruclips.net/video/eiQuBonhGiw/видео.html) although I had planned on making one of these for a long time. I guess the inspiration was to get off my butt and make it. All parts are 1/4" plywood, laser cut to fit, wood glued together, finished with spray paint, assembled with 1/4" hardware, and I used self adhesive white memo board film for the writing surf...
Bee Vacuum Video
Просмотров 7884 года назад
My DIY Bee Vacuum based on a cordless RYOBI leaf blower, a 5 gallon pail and 3D parts of my own design The Ryobi leaf blower cost me $20 off of Kijiji and the bucket was $3.00. The 3D printed parts were either designed by me from scratch (e.g. the adapter ring parts) or modified from some 2-1/4" dust collection blast gate parts I downloaded from Thingiverse.com. I figure I used about $15 worth ...
Halloween Smoke Machine Box
Просмотров 244 года назад
Today I build a simple open ended, sloped top plywood box to protect my smoke machine from the worst of the elements during Halloween. Made from rough 1/2" plywood all the cuts were made at the Halifax Makerspace (halifaxmakerspace.org) while assembly was done at home using my improvised clothes washer workbench.
Disposable Glove Holder Assembly
Просмотров 624 года назад
Using my washing machine as a mini-workbench to assemble a workshop holder for a box of disposable gloves
DIY Laser Cut Painters' Points w Supporting Lazy Susan
Просмотров 765 лет назад
DIY Laser Cut Painters' Points w Supporting Lazy Susan
What happened to the volume .?
Good question. I have to jack the volume up on my own Mac to hear what I'm saying. I don't recall the volume being that low but I can't be sure it it's always been that way.
Nice and simple! Thanks for sharing.
Marcel...any chance you would share the file? I think this is GREAT and my grandson would love it
I’ll see if I can find it. It’s been probably about three years or more but I’ll try to dig it up.
Version 2 with a better sized safety leaver is now up here on Thingiverse. www.thingiverse.com/thing:5856410
Could have placed wicks in the wax cubes and turned them directly into candles. Love the setup
This is the best low budget setup by far. Everyone else is doing too much, thank you
This is great! Thanks for sharing.
Nice video!
Best bee's wax rendering using zero carbon, will try it tomorrow.
Great video, Marcel! Thanks for sharing.