Видео

Thank you great job. Thank you

Glue a small magnet in your plastic cup. Simple is, simple does. When not if, you knock over the cup, they don't go every where and cant find 1 of them and stop everything in the tracks over 1 nut or bolt. 🙄🤔

is there somewhere i can get this now??? i cant fine it anywhere

The video was great, then you ruined it with your poor taste in noise some call music. Sorry 1 dislike headed your way.

the wedsite not working OK?

It's fun watching someone do things like this who aren't mechanically inclined.

Doing a great job explaining step be step, one thing,it's not a driveshaft it's the crankshaft, but otherwise great job!

Just so you know, bud, OL does not mean "point zero L"😃 . It means "over limit". IE the resistance is infinity or out of range if you are using the wrong range setting to give a correct measurement

Great Video... thanks so much for sharing👍

I thought you said you was going to cover 2 methods of how to repair this

When he says reboot does he mean turn it off then back on or is there a reboot button I don't know about? I keep losing the changes I made in settings when I turn it off and back on

Every time I reboot, I lose all the settings I just changed. Does anyone know why?

Good work, noting more to be worry abouth, Good tool its more than 50% of all the work..😉

must be a common thing, just noticed mine was broken off

Way too much talk about doing the job and not enough doing. It would have been much more helpful if you replaced the arm.

I have the same lawn mower as you. Can you tell me what pto clutch part number is so I can the right one. thank you

Hi everybody! Can anyone here help me? This link has no more downloads (MR BURNS 8GB Image - 800-in-1 Vertical Classisics RetroPie Image ). I once have downloaded this image, but lost it somehow. Can anyon here send it to me? Many thanks in advance!

Grat example how nice you covered every step into detail! Great job😊

I squirt any of mine with oil or pour some old oil on then smack the flywheel nut with a hammer to break any rust seals around it spray again with oil then unscrew

Stator

drive shaft lmao

This seems to be a very common issue with the Wranglers. Mine needs a fix up job too, so thanks for this how-to! I guess the robot that sticks these on during assembly either needs an overhaul, or maybe a whole new set of instructions on how to do it right. 😁

Oh my Lord!!! Thank you!

Scott, is it possible to keep the on/off Arcade1Up switch as-is on the control panel? Or with this mod do you need to move it to the back or is that just preference? Same question for the volume button?

any updates?

No more arcade videos?

How do I get the 5/8 bolt holding pto on loose. When I try to loosen it w ratchet engine turns over.

Thank you

Great video..

Dumb questions if you have a 60 and 1 does it automatically default into vertical mode on a wide screen monitor?

WHAT? Nuts are bolts and bolts are nuts?? I'm confused.

Great job on this review. Very clear and comprehensive and well edited. Especially glad you covered the volt/amp hours thing. I have had my Kobalt 80v for 4 years come August. I have loved it...until now. but it bogs down in moderately long (5 or 6 inches) grass and quits if I don't raise it up and allow it to recover engine speed. If I don't raise it up then it dies and will not restart, it just beeps. I have two fully charged batteries, so i is not them. Might this be the resistance sensor? If so, is this a DIY fix or no?

2024 no longer downloadable. My USB crashed... I can't redo this anymore. :(

Doing the Same thing this weekend. Like the IRONMAN Shirt. Thanks for the Help.

Can't thank you enough Scott as I have exactly the same Craftsman DYT4000 tractor and as of today, my alternator/stator just fried itself. Ordering new alternator tonight online and trying the repair this weekend. Wish me luck. This was the best tube vid I've seen perhaps ever. Regards, John

Thank you for this video! Very helpful

Hey Scott! # years since you produced this video. Any changes you've made? Just bought the Arcade1Up Space Invaders cab. Hoping to pretty much do the same mods as you have done with your SI cab. Thank you So MUCH for all your helpful videos. I might just use the 3 button hole (instead of playing Gun Smoke) on the DIY Retro Arcade SI control panel for the 2-in-1 arcade switcher button. Maybe if I have issues I'll pay for you to drive up to Indy to help me out - LOL! Appreciate all your work. God bless!

12:30 It’s Player 1 S2 And Player 1 S3!

still one of the better start up builds. thanks for this!

Good Job !! Thanks

Great video! I repaired my 2017 Wrangler rear window defrost tab with the Permatex adhesive. This worked great for 6 months and now the tab has popped off again. I will be attempting a soldering repair following these steps.

2ah

So, you need to now carry a deep socket and wrench to get that off though 🤔

One of my contacts is off on the rear glass, however I am not getting power to the rear. When I press the button the light should still come on correct? I have checked the fuse and relay. The knob works as far changing from vent to defrost etc, but the light for the rear defroster is not coming on.

Bloody perfect mate done in with the video open what is that little part thoughbthat you replaced where can i source one ❤❤

What happened to your Space Invaders cab?

With the new panel what did you do with the On/Off and Vol buttons that used to be available on the old factory install panel?

So are high scores not able to be saved on a 60-in-1 once power is turned off? Any way to make that possible with the power off?

How do you replace that nozzle? Mine broke off.

Great video learned exactly what I needed,you were very good at explaining each step thanks Scott, Glenn from Ontario Canada