Видео

Hi i have 2 routers 1st router is core, and the 2nd is access concentrator, i put my isp 1 and 2 in my core router, and i connect router 2 using ospf, how can i configure PBR? thank you

Hi, Thanks for this clear concept of M LAG. I would like to request you to let me know that in this case traffic will be flown by both the path simultaneously or flown by any one path at a time? What happen if ICCP connectivity goes down in any case?

Greetings brother, I congratulate you since your level of knowing how to explain is very good since you speak slowly and try to make each episode understood so that it seems very easy to apply these classes. Now, I have a very important question that I have not been able to detail in ospf, in case we have 2 or more service providers and we want to deliver public IP to 1 client that is 5 routers away from the edge as is done in ospf Or is it true, how is it done when we want to make a fiover in the same rb number 5 in case the supplier goes down? A very good question and I would like a great answer or if possible a video, thank you very much. Thank you again for so much, Wilmer, greetings.

Good afternoon friend Wilmer, in this case it would be if the switch was configured in bridge, but if we have the switch configured in tagged and untagged mode using separate vlans towards each router, then this episode is not included in this type of configuration, correct?

Could you please assist me step by step guide for this lab with snap shot pictures if possible? Sir, Hopefully, you can. Thank you, Sir

Спасибо!

Does the failover work on PPPoE (main) to static IP (backup) connections?

porque en la 7.15.3 no aparecen la src address list en advance

very good! a chinese fans!

Thanks! this was exactly the fix I was looking for. CPU stays under 35% most of the time now and I learned how to VLAN better!

Thanks one more agin

Thnks for brightening my knowledge. How do you install GNS3 on your server and Cloud remotely with VPN?

Gracias amigo me costó un poco porque no conseguí tutorial en español

muchas gracias por el video ,con ganas de aprender ingles tambien.

thank you

I have a somewhat simple task, setup 3 ports on the same VLAN and be able to establish communication. I tried following your steps where I would need them but I cannot for the life of me get a ping to any device between the 3 ports. So if I have 3 PCs plugged in, they can't see each other. hmm..Basically setting up a failover for WAN connection, 2 firewalls and one modem(ISP).

This is a very good tutorial on VLANs on Mikrotik CR3XXX series. If you can help me please, I want to configure CRS3XXX switch so that its not Router-on-a-stick rather Inter VLAN routing in switch itself.

Hey Liked the video on firewall. Nicely explained. Can you give something on Mangle Tables ?

Thank you for an excellent video! What is the setup for the rest of the router?

Hello. Do i need working with the VLAN ids, if i have only 1 network and 1 subnet and i dont need to separate some traffic?

Thank You Mr.

Great! Just a tip: there is no need to monitor ISP 2

buenos días maestro , muchas gracias por la información avanzada y explicaciones respecto del uso de vlans en mikrotik, hace un tiempo se me presenta un problema con los crs 317 , que se enlazan entre si con trunk de fibra a 10Gb, en el mismo switch tengo modulos sfp de cobre de 10Gb y de 1 Gb , al funcionar enambos extremos con swos , presentan link paused interrumpiendo las conexiones, a que puede deberse este problema? existe alguna limitacion conocida respecto al buffer cuando se utilizan modulos de diferente tipo 10G y 1G? gracias

Does this work with the rb750gr3?

Thank you a lot! This video helped me to understand how make trunk ports from webfig/winbox on my crs310s.

Wilmer buenas noches, cuando volverás a subir videos en su canal en español? 😭

Hello, I hope this message finds you well. We are currently working on transmitting live video using Wi-Fi communication for our project. Our setup includes a MikroTik Groove configured in station mode, a TP-Link CPE 220 in Access Point mode, and a Raspberry Pi HQ camera. While we have successfully streamed live video using the RTSP protocol, we are experiencing a significant delay of approximately 2 seconds, which is problematic for our application involving drone use. To address this delay, we plan to switch to the UDP protocol for streaming. However, we have encountered an issue when using VLC Media Player to view the live stream over UDP. The video does not appear on the screen; only the time information is displayed in the bottom left corner, as illustrated in the attached picture. This issue also occurred when we increased the video quality while broadcasting with RTSP. Could you please provide any insights or solutions to resolve this issue? Any guidance or recommendations would be greatly appreciated. Thank you for your assistance. Best regards,

I hope that there's an option to redirect browsing to wan2 and games to wan1 with this setup :)

I love the Tutorial. I used VMWare Workstation Pro for this setup. It is now free for personal use. Everything works. One suggestion. Please consider running the GNS3 Web UI with the Light Theme in your tutorials. I understand why you may not use that in your work but the colored text on black background is very hard to read in the tutorial. There is simply not enough contrast between text and background even with the high def settings in RUclips.

thank you, again😁

muy buen video, pregunto en el paso 5, cuando se crea la vlan table, los puertos para la vlan 10 y 20 son exactamente los mismos. mi pregunta es: no deberia tenes los puertos trunk y de acceso especificos para cada Vlan ? Saludos

Thanks a lot

Beautifully explained! Thank you, Chief !

You are simply the best Mikrotik trainer I have seen.

witam, ponawiam pytanie: jak zmienić nazwy pe1 na nazwę moją - piętro_1 proszę o odpowiedz pozdrawiam Daniel

Gracias amigo me ayudaste un montón

buenas amigo wilmer al colocar otro valor en PVID se elimina la vlan 1 cierto?

This is most useful knowledge that I was looking for, I wish I can like it 1000 times. Thank you so much for this content.❤

Currently, i am facing an issue cannot access the web server from the local network. any possible way to allow local networks to public websites?

Que software usas para probar la configuracion de la topologia de red?

Thanks Wilmer, I'd been struggling with configuring mlag for days now, after watching your video, I had everything working as I needed in a couple of hours. I appreciate you sir. 🖖

Hello CRS310-1G-5S-4S+ vlan tutorial?

Спасибо!

Thank you 🙏

tnx it helps a lot

good stuff profesor Wilmer.... this is fantastic...!!!

Just got here looking to properly understand VLANs the Mikrotik way, your channel is impressive! Do you have a video on how to configure VLANs in devices without a switch chip?

Great video, but what if i have two internal servers how to forward to the second server

Very useful video

This video was SO helpful. I went through many many guides and this was the one that tied all the pieces together. Thanks!