Видео

Thank you! You just saved me a lot of time! 😃

Job i might have to tackle so very handy vid. Should there be washer of some sort in metal connector

Didn’t really work for me,unfortunately . The top part wouldn’t unclip without first removing most of the bottom parts first.There was no way it was going to lift clear of the ‘white tube’ going into the solenoid,otherwise. Also there was still water in it,unlike yours,which didn’t help either. The bit about fishing out the ‘o’ ring came in useful though

Thank you so much, I found this extremely helpful 👍

Great work!

If I have replaced the part and the tank still isn’t filling up it’s just a slow drip still any idea what the issue may be?

Nice one. Thanks

Perfect video. Changed the washer last week , £4.99 ! …. A lot cheaper on Amazon ..

Thanks

Hello! Mine doesn't show the blue light when it's off , any idea why? thanks.

Thanks man - I hadn't got a scooby doo about this before watching your vid. First time my element blew on the old electric oven in my flat. I'll try getting the old element out later to see if I can find a serial no to get a replacement. Better that than fork out for a new oven when its 300-500 quid a pop. What a friggin rip off.

Thanks just repaired my makit the same way

this is great but good god man - PUT SOME GLOVES ON 🤢

It cost me £5 for the washer from my local Screwfix but I reckon I’ve saved at least £50 for a plumber. Thank you so much! 🙏

Brilliant video thanks. It fixed it too.

2nd time I had to do this with the same drill. Thanks.

Glad I found this video as been looking for this info. The problem I have is that when the cover and seat are up the seat part is not staying up just falls forward. Any suggestions how to fix?

Thank you.

Great video thanks. Any ideas why my shower trips out when on high but works fine on other settings please?

You mentioned the noise level, what db would you tap out on? I have noise sensitivities as I'm autistic but I also wear ANC ear bud almost all the time. Nice looking bit of kit. Thanks

Very good thank you.

Hi I have my pump out after a F05 fault no bits in it but when you try and spin the propeller of the pump it will not spin freely it ls like it has a resistance everytime you push it around then goes past it and around again to a little resistance and around again Is this Normal ! Thanks

Thanks

Do you know if it's possible to split the drum so you can change the bearings on this model? Becouse I dismantle mines and it looks like it's glued and heated.

This video was bang on. My cistern is now fixed for the princely sum of £ 3.71 (inc VAT). As you would say - "Thats us".

I’ve just watched your excellent video and it has saved getting a new machine, the waste pipe was well blocked, thank you once again.

Thank you for posting this video.reakky helpful

Thank you for this, looks really helpful 👍

Had the same problem and the part was broken so obviously I replaced it but now I can't get any water when flushing and the notch is definitely lined up I've checked 3 times any advice?

Hi, thank you for this video, I just fixed my Milwaukee M18 using your method, it's just superb and simple.

Cheers mate, 5 quid from Screwfix. Easy fix

Any ideas why the little circular diaphragm squeaks (the one right next to the nut you tightened)

Fantastic and fixed thanks! 🙏🏻 👌👌 but £5.99 in screwfix btw. Very happy Mrs lol. It was taking an age to fill through the leak. There’s still a drip through the elbow that comes out? But nothing close to before.

Thanks for posting this, it’s cleared up how to replace the solenoid on my mira vista as access issue is the same as your video.

I'm going to be trying this tomorrow mate.cheers.

Just fixed mine too! Well pleased. Had been doing my head in!!! Thanks so much 👍🏾👍🏾👍🏾

Thank you so much man, I was gonna buy a new one cuz it didn't open and just by tapping it with a hammer it opened

You never bring to the surface while still running stop the motor before coming to the surface and no problem

I fixed my stuck chunk by your way, thanks a lot.

Hey, just tried your gentle technique on a Bosch PSB 13RE keyless chuck hammer drill. Now it’s working again. Thanks for your video!

I was thinking about a 796, so thanks for the tip about the 996.

your accent sucks

Fantastic, thank you for a well done video 😃👍

Thank you I did it!

Hi there , I’ve done all you have shown in the video but I still get the error code lights. I cleaned the drain pipe too. Is there anything else which could be wrong? I’m reluctant to get an engineer out (£150) when a new machine can be bought for £250. Thanks.

My chuck became stiff to turn yesterday after drilling some galvanized steel on a ceiling! So the knob used to turn easily by hand but now it needs a stronger grip to tighten! Why do you think? Did it reach its lifetime or could there be some steel debris in it?

Just flew into Scotland, place we’re renting has this set up and EXACTLY the same issue. Thank you.

Brilliant £2.36, 10 mins of my time and it's done!!!👍🏻

My machine pump is not open what to do ?? It's moving a little bit but not opening

No offence meant to the chap making this video but I can't believe that all these people don't read the manual that comes with the washing machine. They tell you how to clean the filter and how often to do it!