Видео

Where can I get fuel pressure sensor for my 54 reg 1.9 cdti all part numbers are different which is equivalent correct one to fit

I have had to perform this fix on the wife's motor. With this guide, it was effortless but for the need for a magnifying glass. The usb microscope makes it seem like it can be seen without some kinda magnification but I found that my camera had a macro mode on it so I used that to identify the cracked solder joints. All I did was reheat the joints with a hot tip and used a tiny amount of solder but anyone can fix this with a cheap solder kit and this guide. Brilliant video, thank you.

Had these lights on for 1week grrrrr Watched this Wiggled the connection under drivers seat Abra cadabra 😅😅😅😅 Thank you not stressed now

Hi my friend

Hi, I am having similar issue sith my saab for 4years now, and i have changed a total of 4 ac compressors in 4 years, each time I have the mechanic install a new compress the ac comes on blowing cole air but it doesn't chip out when it suppose to stop, it just continues to run continuously and that cause the compressor to burn up each time because its running so hot without chipping in and out. Can you tell me what could be the issue for the ac compressor not chipping in and out? Could it be some type or sensor gone bad?

What tool did you use to measure? I'm having same code. Did timing chain, replaced solenoids and replaced intake cam sensor. Still the same error code. My fear is if it's damaged groove or the Vanos gear itself. Sadly, the mechanics nearby cannot or not willing to properly diagnose this issue. Any help would be appreciated

I only wanted to know how to get the pipe off the sensor and the bit you skipped! 😂

Nice job , j'ai le même problème

is this a 2.0 Diesel?

grande complimenti!!!

So whats the duagnosus here ? Bad map ?

Thanks for this video,mine is having the same problem so I go to check it out .

All I see is problems with these Ford Custom vans , they seemed ok up to 2015 then the face lift models especially the new ones are problematic with all kinds of issues…. It’s a shame Ford have gone down the pan as I’ve many many good ones In the past namely Mk 5’s 6’s and early 7’s , I wouldn’t buy another one… 😂

I have renault zoe 2017 and my car electric motor is damage new electric motor cost is 5keuros that too much for me can we repair electric more?

Hi thanks for video Is the turbo boost sensor same place on the 2010 diesel 1.4 tdci please ?

any ideeas about dtc e510 or D900?

Top guy👊🏾

Mine won’t beep at all. What can be wrong??

So you used a " decade box "? Is that a load of resistors in a box ? So if i shove a 3 ohm resistor across the two contacts that should replicate the seat devices " resistance " ? And the fault should clear ... ? So does the CAM BUSS look for 3 ohms across all " transducers " coils , lamps etc ? In order not to throw up a code ? And the CAM BUSS im presumimg is a square / pulse wave , which i should be able to SCOPE , but how does tye CPU know WHICH DEVICE is not giving 3 R , or is it more complex ?

Hello,part number for the sensor?please.thanks

Very explanatory & helpful, thank you.

It helps! Thank you so much!!!!!

Them nissan Qashqai are a heap of trouble staying clear .Renault engine of course.rubbish.

Hi, did replacing the ABS sensor solve the gearbox fault too?

great video my son has a polo 9N 2002 and without guys like you we would be changing so many things as a fault and found a fuse cracked could do a repair

hola gracias por el video tengo el mismo motor quela tuya, me podria decir que numeracion tiene este sensor a ver si es el mismo que elmio, tambien podria decirme numeracion de culata queno la encuenro por nnngun sitio, gracias

Here in Greece they ask 120 euros if you take the cluster to the electronics guy. 220 if you take it to the mechanic,so he take out the car and send it for soldering.

Thanks mate, Followed your instructions, Great help. Thanks again

i had my cluster checked by rac and auto electrcian both said for a ford 2005 it cluster; even the repair place said it the cluster with all it faults put it in but nothing happened ???

so any epromm on any control unit in the car is st right?

I have the same issue, what is the name of the box that you used? Thanks

Hi on our 308 CC we have the fan running all the time when the engine is switched off. I followed your checks and find the voltage is only 3.5 volts, also the sensor resistance is 2500 ohms when cold. Should i trace the reason for only having 3.5 v instead of 5V? Thanks

to test the relay cant you just take the relay to your left and use that?

Hi, Are you based in Birmingham ?

I have the same problem but seems very intermittent, could stay off for months or weeks but when it comes on switch engine off and on again and may not do it again for weeks

Useful video for some though it is very worrying that Renault don't acknowledge there is real design issue with these. I pray the 135 hp used in the Zoe GT Line is designed better. The letter 't' does exist in the English Language. 🫢

Great to see! Not only a full diagnostic but confirming problem source.

Tengo el codigo p0012 , el motor arranca y se mueve , cambia solenoide vvt alguna recomendación de que revisar ?

❤

I have x100 small can l use to pragramming

Hi there will truecode do the 2011 Vauxhall combo van

what snap on scanner was you using please?

Did you have to get new keys or programme existing keys?

Yep, same comments as below, thanks for an informative video that showed exactly what to do. I haven't done any soldering in years so was pleased to see that I still had the skills :) although I did have to invest in magnifying glass now, I'm old.

Is that power steering not working or very hard before you fix it

I think that light is signalling unsanitary environment inside the cabin 🤯

All my dials work but speed is showing high, when doing 60mph it shows 120mph any idea what this fault could be please ?

I tried this and 50 km later.... nothing. My Focus seems to work just fine now.

Have a 2014 transit custom. Have the licensed 1yr copy of Forscan with Genuine module and cannot see the PAT’s feature within forscan tools menu for setting the keys. Do you know whether this feature is blocked on models of this year? Cheers

Fixed thank you