Видео

please doing contents like these................much appreciated brother.... form Sri Lanka......

Hi. What solver do you use to calculate the effective mode index?

Hello there, I am working on a project about cooling electronic components with heat sink, and i am want to make a simulation in comsol multiphysics if you can provide some help.

Hi where on RUclips is the video where you built this geometry from scratch?

Pls can you upload Fibonacci structure for SPR Sensor simulation

Does the system require java while running python code ??

Please do video on RVE geometry in matlab and shifting it to comsol

I call BS on this

Hi, I have defined the circuit of the half-bridge inverter in the COMSOL environment based on your explanations and the node numbers in the corresponding physics. However, it gives an error during the computation. Could you please guide me?

How to get 6.3 COMSOL Software?

What about the different physical dimensions how to set the dimensions for these drawings in console, also is it possible to hand sketch something and take a photograph and than use it in the comsol !!?

I have a problem with simulation of detection of stroke, could you help me please

I followed along but ended up with zero solution. I used same boundary conditions as you.

Sir I have some data which I export from Comsol and then I have to use some mathematical equations which I do it in Matlab to get the final plot. Can I do this in paraview?

Sir want file

I am getting this error once I compile the code. How can I resolve this issue? com.comsol.util.exceptions.com.comsol.util.exceptions.FlException: Exception: com.comsol.util.exceptions.UnexpectedServerException: java.lang.IllegalStateException: java.io.IOException: The system cannot find the path specified (rethrown as com.comsol.util.exceptions.FlException) Messages: java.lang.IllegalStateException: java.io.IOException: The system cannot find the path specified

hi, i have a question, is there if i only have 1 domain in my model?, im working with componets by FDM ( to torsion ) therefor i have a structure with internal pores, actually i have problem with these pores, the solution is select the boundaries to do a fine mesh as your video?

Very interesting, many thanks for the valuable file

Can u make videos on acoustic simulation with tips?🤔

Great job! Thank you for your video. Like and Subcribe.

I need a help regarding PVT Furnace Model for Silicon Carbide Crystal Growth.

I want some help regarding static structure problem. While solving the problem I am getting relative residue is greater than relative tolerance. How to resolve this issue.

how can we find the relative permeability and effective saturation variation with respect to time in two phase flow through a porous medium

Thank you for sharing this video. I meet some problems about the imput material property of water. The expression you inputed is density_water*ratio_w. But according to their meanings, Does the expression denotes the density of ice? and you said that the density of water is not fixed, but the density of ice is a constant value. so i am confused, could you please help me answer my questions ? Thank you sincerely.

I'm trying to 3D simulate a very simple perovskite solar cell in comsol but although analysis converges, no parameters in Energy Level (semi) is becomes available to plot. It shows the following pop up whenever I try to plot it. But in 1D and 2D simulation, this problem does not occur. How do I solve it?

Great job please do vedio about plasma modeling

Thank you!!

Sir what's the purpose of line average in comsal multiphysics

Sir it's great video thanks Could you tell ma for creating videos how to check mesh independent in nusselt and Sherwood number of mseh independency and how to creat table for any 2 parameters value caluations in heat transfer in fluid. Please help me for creating videos about that nusselt and Sherwood number

Hi, I need your help in learning few COMSOL concepts. How can I contact you?

Can we get organ of the body

I wish you spoke about how to create mesh for 3D model with doping profile too. But your video was great. Thanks another.

Thank you so much for the video. It helped me a lot!

Please do as soon as possible on level set field coupled with heat transfer incorporating volume fraction for bubble nucleation and growth when substrate is boiled.

Hi, I have problems with fillets on laminar flow, the wall condition impose a layer boundary mesh that is giving me troubles between two fillets (3D model). I tried to corner properties to use the splitting condition ( as some tutorial for CDF meshing says) but the results are not different, do you know some tips to solve this kind of problems??

this was an EXCELLENT tutorial an tutorial - thank you so much - i wish comsol's tutorial would have the same quality. was the mph file somewhere to download?

If this podcast is made with some animation or visualization it will much more incredible. By the way thanks for this

How to use AI to simulates my models for exemple COMSOL

Impressive video! I have a small question regarding your model. You define a function named run in Python. I’m wondering if it's possible to use the Java file saved from COMSOL to generate the run function, or alternatively, if it’s possible to use Python to directly run the Java file from COMSOL?

Hi BK, Could you please create a video on complete design of a capacitive accelerometer in COMSOL?

can you suggest literature related to all data and model given in the video?

1. how can i calculate the strain in plate ? 2. what about the plate material ?

i cant find caed model of this

I need to evaluate punctual variables in the same double table in python

I used mph python for my work but it doesn't offer the ability to extract the punctual evaluation for multi variables if I change it to API it shows double array which I can not show it directly in python so how could I extract the double tables in python?

Hi, i need some help in comsole How can I reach you?

are these similar to the "liquid crystals" found in LCDs?

Can you guide me from the first step to running the result? 1.Materials, 2. Moving Mesh, 3. Physis

Hi BK, how are you going? Could you explain me why do you delete the wetted wall in the multiphysics session? I have a doubt, if I'm analyzing macroscopic fluid flow of water and air, Do I need to use wetted walls?

Hello,can you please help me in my problem with comsol.